• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.551-558
• /
• 2001

The horizontal drain method is one of methods improving reclamation ground. This method reduces consolidation time by using drained installed horizontally, and negative pressure is applied on end of these drains by vacuum pump. But, effective negative pressure still wasn't evaluated in applying this method to reclamation ground. To estimate optimum negative pressure, soil box test that make a model the in-situ by installing horizontal drains in the center is performed pressing different vacuum pressure In the laboratory, and the variations in settlement and volume of drained water through the drains during consolidation process were measured. Also, water content with distance from drain and with depth is measured after the test.

• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.5
• /
• pp.411-418
• /
• 2020

A reformer is a device for producing hydrogen used in fuel cells. Among them, methanol steam reformer uses methanol as fuel, which is present as a liquid at room temperature. It has the advantage of low operating temperature, high energy density, and high hydrogen production. The purpose of this study is to improve the internal flow of the pressure vessel when a bundle of methanol steam reformer in the pressure vessel goes out to a single outlet. An analysis of equilibrium reaction to methanol steam reforming reaction was conducted using Aspen HYSYS^® (Aspen Technology Inc., Bedford, USA), and based on the results, computational analysis was conducted using ANSYS Fluent^® (ANSYS, Inc., Canonsburg, USA). For comparison of the results, the height of the pressure vessel, outlet diameter, and fillet was set as variables, and the optimum geometry was selected by comparing the effects of gravity and the amount of negative pressure.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1999.11a
• /
• pp.40-45
• /
• 1999

The effect of the addition of helium, neon, argon and xenon on the production of negative hydrogen ions has been studied in a magnetically confined dc filament discharge. The addition of helium and neon produced effects similar to an equivalent increase in hydrogen pressure. However, the addition of argon and low fractions of xenon produced significant increases in the negative ion density for hydrogen at pressures around 1 mTorr. The addition of argon and xenon, by increasing electron density and decreasing electron temperature, achieved conditions closer to optimum for negative ion production. The largest enhancement of negative hydrogen ion density occurred with the addition of argon; it is suggested that this is due to a resonant energy exchange between excited argon atoms and hydrogen molecules.

• Journal of the Ergonomics Society of Korea
• /
• v.31 no.3
• /
• pp.455-461
• /
• 2012

The aim of this study was to investigate the appropriate elasticity of the textile material used for making women's girdle. Background: The elastic textiles have been used for making girdle. The hard type girdle gave high pressure on the body to make slim look. However, excessively high garment pressure caused negative effect to human bodies. This study studied the material giving proper garment pressure in girdle. Method: In this study five experimental girdles were made fabrics with various elasticities. The change of garment pressures and body girths were measured after subjects wearing the experimental girdles. The garment pressure was measured at 10 points. Body girths measured at abdomen, hip, and thigh. Results: The garment pressure of the commercial girdle was high at side of waistband, side femur and back gluteal fold. The experimental girdles made with high elasticity material definitely lowered garment pressure at those points. After wearing experimental girdle their abdomen and hip girths measurements were decreased. But, thigh girth was not reduced. Conclusion: The girdle made with excellent elasticity materials reduced garment pressure significantly and it made body slim as much as the commercial girdle except the thighs. Application: This study provides guideline for the developing girdle that applying optimum range of garment pressure with body slim effect.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.18 no.4
• /
• pp.4251-4258
• /
• 1976

In the construction of earth dam, embankment and highway by filling, a compaction contributes to increasing the density of soil by applying pressure. The effect of compaction depends on various factors such as soil type, moisture content, gradation, consistency, and compaction energy. In this study, the correlations amone maximum dry density, moisture content, dry density, and moisture content are analyzed. Some results obtained in this study are summarizep as follows. 1. The maximum dry density sinoreases with increased of optimum moisture content and the correlations of them can be represented by; ${\gamma}$dmx=a-b(W0) 2. Maximum dry density and liquid limit show negative linear correlation and can be represented by; ${\gamma}$dmx=a-b(LL). 3. Optimum moisture content and liquid limit, plastic limit show positive linear correlation and can be represented by the following equation, W0=a+b(LL) W0=a+b(PL). 4. Liquid limit and plastic limit show positive linear correlation, and can be represented by the following equation, LL=a+b(PL).

• Korean Journal of Materials Research
• /
• v.22 no.6
• /
• pp.309-315
• /
• 2012

Metal foam has many excellent properties, such as light weight, incombustibility, good thermal insulation, sound absorption, energy absorption, and environmental friendliness. It has two types of macrostructure, a closed-cell foam with sealed pores and an open-cell foam with open pores. The open-cell foam has a complex macrostructure consisting of an interconnected network. It can be exploited as a degradable biomaterial and a heat exchanger material. In this paper, open cell Mg alloy foams have been produced by infiltrating molten Mg alloy into porous pre-forms, where granules facilitate porous material. The granules have suitable strength and excellent thermal stability. They are also inexpensive and easily move out from open-cell foamed Mg-Al alloy materials. When the melt casting process used an inert gas, the molten magnesium igniting is resolved easily. The effects of the preheating temperature of the filler particle mould, negative pressure, and granule size on the fluidity of the open cell Mg alloy foam were investigated. With the increased infiltration pressure, preheat temperature and granule sizes during casting process, the molten AZ31 alloy was high fluidity. The optimum casting temperature, preheating temperature of the filler particle mould, and negative pressure were $750^{\circ}C$, $400-500^{\circ}C$, and 5000-6000 Pa, respectively, At these conditions the AZ31 alloy had good fluidity and castability with the longest infiltration length, fewer defects, and a uniform pore structure.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.1
• /
• pp.1-10
• /
• 2003

In this paper, the laboratory test results with middle-sired ,soil box test in modeling the in-situ installing of horizontal drains are discussed the estimation of the optimum negative pressure. The test was carried out in the different vacuum pressure conditions together with the measurement for the settlement and volume change of drained water by the installed drains during the consolidation process. After the test, the water content was measured to both directions of lateral distance from the drain and depth of the soil, to find out the distribution of ground improvement and strength enhancement. From the analysis on the distribution of water content, the gradual application of vacuum pressure to higher level by pre-determined stages starting from low vacuum pressure is found to be effective and desirable. In the comparison of the degrees of consolidation with elapsed time, the calculated value by the prediction method based on the Barren's conventional theory showed a good agreement with the measured value. With this, It is positively considered that the applicability of the prediction method based on Barren's theory to the practical design of horizontal drains can be justified such as in the calculation of drain spacing and consolidation period.

• Journal of Dairy Science and Biotechnology
• /
• v.41 no.1
• /
• pp.1-8
• /
• 2023

Response surface methodology (RSM) is a statistical approach widely used in food processing to optimize the formulation, processing conditions, and quality of food products. The homogenization process is achieved by subjecting milk to high pressure, which breaks down fat globules and disperses fat more evenly throughout milk. This study focuses on an application of RSM including the logit transformation to predict the efficiency of milk homogenization, which can be maximized by minimizing the relative difference in fat percentage between the top part and the remainder of milk. To avoid a negative predicted value of the minimum of this proportion, the logit transformation is used to turn the proportion into the logit, whose possible values are real numbers. Then, the logit values are modeled and optimized. Subsequently, the logistic transformation is used to turn the predicted logit into the predicted proportion. From our model, the optimum condition for the maximized efficiency of milk homogenization was predicted as the combination of a homogenizer pressure of 30 MPa, a storage temperature of 10℃, and a storage period of 10 days. Additionally, with a combination of a homogenizer pressure of 30 MPa, a storage temperature of 10℃, and a storage period of 50 days, the level of milk homogenization was predicted to be acceptable, even with the problem of extrapolation taken into account.

• Journal of Korea Water Resources Association
• /
• v.33 no.3
• /
• pp.289-298
• /
• 2000

In order to minimize the impact of water hammer In a pipeline, a determination of optimum position of hydraulic structures with best operation of pressure relief valve was explored at the Seobyun pumping station. Method of characteristics is used to simulate a surge impact originating from abrupt stop of pumping operation in a pipeline. Genetic algorithm shows a powerful capability in searching a global solution, especially for a nonlinear problem The application results suggests that the maximum positive pressure can be relaxed by decreasing the opening time of pressure relief valve, meanwhile the maximum negative pressure can be relaxed by increasing the opening time of pressure relief valve. This study shows that the integration of a genetic algorithm with a transient analysis technique such as method of characteristic can improve the design of hydraulic structure in a pipe network.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.175-182
• /
• 1997

The purpose of this study is to investigate the effects of intake manifold shapes to improve the engine performance in a 3-cylinder LPG engine with a closed loop fuel supply system. To know the flow resistance of intake manifolds with shape, the intake negative pressure of each runner in intake manifolds were measured by using the digital pressure meter at each driving condition. And, the engine torque and power have been measured with an engine dynamometer while adjusting the optimal fuel consumption ratio with a solenoid driver. As 속 results form this experiment, the torque characteris- tics were more improved with the plenum chamber(B type intake manifold) than with the banana type(A type intake manifold). The torque characteristics were improved at mid-engine speed(rpm) range as the inner diameter of the intake manifold became smaller. And also the optimum volume among the examined plenum chamber volume was 0.74 times(590cc) the displacement of the test engine.