• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.8
• /
• pp.478-488
• /
• 2017

Stormwater filtration is widely used for the urban runoff treatment. However, intensive maintenance and lack of information about the performance have resulted in an increased need of proper evaluation. In this study, the performance of an upflow stormwater runoff filtration system, consisting of a supporting unit and a filtration unit filled with a ceramic media, was investigated. The maximum head loss increase was about 3 cm under the suspended solid (SS) load of $30kg/m^2$ and the SS removal was more than 96%, when the filtration velocity was 20-40 m/h. The head loss and the porosity of the media can successfully be described by a power model. It was confirmed that the a significant amount of SS can effectively be removed at supporting unit, minimizing SS load to the filter media bed. Several backwashing strategies have been tested to establish the optimum condition. It was found that the stagnant water discharge is important to minimize the SS release immediately after backwashing. Also, the filter bed loaded with $400-450kg/m^2$ SS can almost completely be washed to reduce the head loss to the that of empty bed. The results in this study indicate that the upflow ceramic media filter is an excellent alternative to stormwater treatment, with high SS removal and long lifespan.

• Journal of Microbiology and Biotechnology
• /
• v.16 no.11
• /
• pp.1690-1698
• /
• 2006

In order to investigate the effect of dissolved oxygen (DO) level on AVM $B_{1a}$ production by a high yielding mutant of Streptomyces avermitilis, five sets of bioreactor cultures were performed under variously controlled DO levels. Using an online computer control system, the agitation speed and aeration rate were automatically controlled in an adaptive manner, responding timely to the oxygen requirement of the producer microorganism. In the two cultures of DO limitation, the onset of AVM $B_{1a}$ biosynthesis was observed to casually coincide with the fermentation time when oxygen-limited conditions were overcome by the producing microorganism. In contrast, this phenomenon did not occur in the parallel fermentations with DO levels controlled at around 30% and 40% throughout the entire fermentation period, showing an almost growth-associated mode of AVM $B_{1a}$ production: AVM $B_{1a}$ biosynthesis under the environments of high DO levels started much earlier than the corresponding oxygen-limited cultures, leading to a significant enhancement of AVM $B_{1a}$ production during the exponential stage. Consequently, approximately 6-fold and 9-fold increases in the final AVM $B_{1a}$ production were obtained in 30% and 40% DO-controlled fermentations, respectively, especially when compared with the culture of severe DO limitation (the culture with 0% DO level during the exponential phase). The production yield ($Y_{p/x}$), volumetric production rate (Qp), and specific production rate (${\bar{q}}_p$) of the 40% DO-controlled culture were observed to be 14%, 15%, and 15% higher, respectively, than those of the parallel cultures that were performed under an excessive agitation speed (350 rpm) and aeration rate (1 vvm) to maintain sufficiently high DO levels throughout the entire fermentation period. These results suggest that high shear damage of the high-yielding strain due to an excessive agitation speed is the primary reason for the reduction of the AVM $B_{1a}$ biosynthetic capability of the producer. As for the cell growth, exponential growth patterns during the initial 3 days were observed in the fermentations of sufficient DO levels, whereas almost linear patterns of cell growth were observed in the other two cultures of DO limitation during the identical period, resulting in apparently lower amounts of DCW. These results led us to conclude that maintenance of optimum DO levels, but not too high to cause potential shear damage on the producer, was crucial not only for the cell growth, but also for the enhanced production of AVM $B_{1a}$ by the filamentous mycelial cells of Streptomyces avermitilis.

• The Korean Journal of Pesticide Science
• /
• v.4 no.4
• /
• pp.56-60
• /
• 2000

A study was performed to determine the maintenance conditions of the earthworm, Lumbricus rubellus, for the acute toxicity test. To fine out climatic and soil conditions, the earthworms were maintained in artificial soil consisting of sand, clay mineral and peat at different levels of conditions for 14 days. Lumbricus rubellus led to an increase of biomass at temperature $22{\pm}2^{\circ}C$, soil pH $7.0{\pm}1$ and moisture 40%. And four fungicides were tested for acute toxicities to Lumbricus rubellus, according to the optimum condition. The test earthworms were exposed to each pesticide with various concentration gradients. After 14 days, the number of surviving earthworms and their weight alteration during the test period was determined. The 14-day $LC_{50}$ values for the Lumbricus rubellus, of carbendazim, benomyl, thiophanate-methyl and thiabendazole were determined to be 59, 53, 64 and 36 mg/ kg soil dry weight, respectively.

• Korean Journal of Environment and Ecology
• /
• v.18 no.4
• /
• pp.359-368
• /
• 2004

The purpose of this study is to examine distribution and damages of the trails of inquiry of urban natural parks. Those parks were located at south-north green corridor at Incheon being mountainous type of urban natural parks that were core area of urban ecosystem preservation to of urban natural parks that citizens recently made use of them as nature experience type of leisure and recreation place from time to time, and to supply basic material deciding on the ways to improve the trails of nature preservation type. The survey sites included Geyang Park, Baekma Park, Yaksa Park, Munhak Park and Cheongryang Park. The number of main trails was 42 at Geyang Park, 43 at Baekma Park, 9 at Yaksa Park, 28 at Munhak Park, and 22 at Cheongryang Park, and it was excessively more than optimum needed: The number of branch trails of the parks seemed to increase. The bared trail width in average of the roads was 3.5m, while maximum depth in average was 21.3cm. The trails were thought to be deteriorated rapidly without systematic maintenance. The 5th and 6th grade of the impact rating class that required restoration because of serious deterioration occupied 19.6∼78.0%. Based on the findings, the study suggested ways to improve and manage the trails of inquiry of urban natural parks that were placed at south-north green corridor at Incheon.

• Asian-Australasian Journal of Animal Sciences
• /
• v.23 no.2
• /
• pp.240-245
• /
• 2010

The effects of controlled energy restriction and duration of pre-incubation egg holding on fertility, hatchability and hatch losses were evaluated in aged broiler breeders (64 wk). The energy (ME) required for maintenance, activity, growth and anticipated egg production was calculated and offered to a control group (283-471 kcal/kg) from 21-64 weeks of age. In three other groups, ME was quantitatively reduced either by 20% (SER; severe energy restriction) or 10% (MER; moderate energy restriction) and increased by10% (EEF; excess energy feeding) over the control group (CER; controlled energy restriction). Each diet was offered to 130 pullets in individual cages, and the quantity of ME increased with age. At the end of 64 weeks, fertile eggs were collected from each dietary group for 11 consecutive days and grouped under 4 holding periods based on the length of storage (2, 5, 8 or 11 d). The influence of energy regimes, egg holding intervals and their interaction was evaluated on fertility, hatch losses and hatchability. Broiler breeders maintained on SER regime (231-419 kcal/d) produced maximum number of eggs (993) followed by MER (819), CER (624) and EEF (438) during the 11-day period. The percent fertility and hatchability was significantly (p$\leq$0.05) higher in SER and MER groups compared to CER and EEF. However, energy regimes did not influence the loss in egg weight during pre-incubation storage, shell weight, shell thickness or hatch losses as dead germs and dead in shell. The improvement in hatchability in SER and MER groups appeared to be closely related to higher fertility and lower embryonic mortality. Holding of eggs for 11 days showed a linear loss in egg weight with the length of storage, but did not influence the fertility and hatch losses. The percent hatchability on eggs set was maximum when storage period was restricted to 5 days. The interaction between energy regimes and egg holding periods exhibited better hatchability results with SER regime when eggs were held for 5 days. Response to MER was not different from SER. It was obvious that energy restriction during production period had a positive influence on egg number, fertility and hatchability in aged breeders. At 64 weeks of age, holding of fertile eggs for 5 days prior to incubation was adequate for optimum hatchability in breeders.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.845-848
• /
• 2013

Due to intense climate changes and extreme weather conditions a noticeable decrease has been observed in the growth of certain plants. The indoor plant factories would have certain benefits including increase in crop yield, reduction in distribution cost, and maintains the healthy freshness level of the agricultural product. Recently, an artificial light source with optimum wavelength is spot lighted to fulfill the need of light for the indoor plant factories. The energy efficient light emitting diodes (LED) provide the essential light energy for the proper growth of indoor cultivated plants. This work focuses to utilize ubiquitous sensors network(USN) in providing suitable environment for the proper growth of agricultural product inside the indoor plant factory. The proposed system makes use of sensors and actuators, communicating each other through WPAN, ZigBee network. The proposed system obscured the traditional indoor plant factories with easy installation and wireless connectivity of the sensors and actuators along with eliminating the web of wires reducing the initial installation and maintenance cost.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.1
• /
• pp.60-68
• /
• 2012

In this study, the manufacturing process of micro capsulized PCM (phase changing material) for thermal storage performance of latent heat was investigated to save energy during the use of buildings: i.e. use of melamine-type resin as the micro-capsule material and paraffin wax as the inner material that are together used in concrete walls. For the manufacturing process of the micro-capsulized PCM, the amount of SDS addition as surfactant was the key variable and the resulting thermal storage performance depended on the SDS amount. With increasing amount of SDS, the micro capsulation became much easier while the capsule surface became harder. The micro capsules became uniform at an optimum SDS addition. The addition of SDS also affected the thermal capacity: with increasing SDS amount, the heat storage and release tendency at melting point was more clearly manifested. The current investigation is part of a study under progress to explore the use of PCM in concrete walls to save building maintenance cost and energy.

• Clinics in Shoulder and Elbow
• /
• v.13 no.2
• /
• pp.286-292
• /
• 2010

Purpose: Stability of joints and maintenance of range of motion are needed for optimum function. The most common complaint about the elbow joint is joint stiffness. Recent articles have reported good outcomes in the treatment of stiff elbow joints. However, deciding which procedure to use is always difficult. Materials and Methods: Morrey et al. reported that the functional range of motion of the elbow joint is $30-130^{\circ}$ of flexion-extension and $50^{\circ}C$ of supination and pronation. About 90% of daily activities are done using this range of motion. Stiff elbow joints can be classified according to the traumatic events that caused the problem or the location of the main pathology. Intraarticular pathology includes severe articular mismatch, intraarticular adhesions, loss of articular cartilage, mechanical blockade by osteophytes, loose bodies, and hypertrophied synovium. Extraarticular pathology includes severe capsular adhesion due to the trauma or to dislocation, contracture of the collateral ligaments or muscles, bony bridge. Results and Conclusions: The main pathology underlying the loss of extension is the fibrous contracture of the anterior capsule. In this pathology, an anterior capsulectomy would be helpful. The main pathology underlying the loss of flexion is the contracture of the posterior band of medial collateral ligament.

• International Journal of Highway Engineering
• /
• v.8 no.3 s.29
• /
• pp.49-61
• /
• 2006

This study suggests long-life asphalt pavement method which can save maintenance cost by increasing the design and performance period of pavements. The high modulus asphalt binder developed and then various physical tests are performed. Laboratory performance tests and accelerated pavement test are conducted for the high modulus and conventional mixtures. The test results show that dynamic modulus values of high modulus mixtures are higher than those of the conventional mixtures, The high modulus mixtures yield better fatigue, rutting and moisture damage performance than conventional mixtures. Structural analysis is performed and a database is built up for long life asphalt pavement design. Pavement response model is developed through a multiple regression analysis program, SPSS using the database. A design software for the long life pavements is developed based on the pavement response model and laboratory and field performance tests results. In addition, optimum pavement sections and materials are suggested. The suggested AC thickness of long life asphalt pavement is 29cm. A Life cycle cost analysis(LCCA) is conducted to check the economical efficiency of the long life pavement section. The LCCA result shows that initial construction costs of long life and conventional pavements are almost equal, but long life pavement is more profitable in terms of the LCCA.

• Journal of Wetlands Research
• /
• v.19 no.3
• /
• pp.271-278
• /
• 2017

Low impact development (LID) technology has been recently applied for the treatment of nonpoint source pollutants. Rain garden is one of the widely used LIDs since it utilizes various mechanisms such as biological and physico-chemical treatment to reduce pollutants. However, problem such as clogging has been one of the issues encountered by the rain garden that do not undergo constant maintenance. Therefore, this research was conducted to develop and determine the component arrangement of a rain garden system for a more efficient volume and pollutant reduction. Two hybrid rain garden systems having different characteristics were developed and evaluated to determine the optimum design and arrangement of the system. The results showed that the components arranged in a series manner showed a volume reduction of 93% and a pollutant reduction efficiency of approximately 99%, 93% and 95% was observed for particulates, nutrients and heavy metals, respectively. While when the system is connected in a combined series-parallel, the volume and average pollutant reduction efficiency for the TSS, nutrients and heavy metals are 65%, 94%, 80% and 85%, respectively. Moreover, the component arrangement in the order of sedimentation tank, infiltration tank and plant bed exhibited a high pollutant reduction efficiency compared when the infiltration tank and plant bed were interchanged. The findings of this research will help in the further development and optimization of rain garden systems.