• Proceedings of the Optical Society of Korea Conference
• /
• 2004.02a
• /
• pp.288-289
• /
• 2004

The performance of the InGaAs/InP avalanche photodidodes operated in Geiger-mode was investigated for 1550nm wavelengths at room temperature. We find the optimal operating points where the high quantum detection efficiency and low dark current are achieved. For the optical pulse detection, the gated-mode is used to reduce the dark current.

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.07a
• /
• pp.61-63
• /
• 2008

Parallel femtosecond laser processing using a computer-generated hologram (CGH) displayed on a liquid crystal spatial light modulator (LCSLM) is demonstrated. The use of the LCSLM enables to perform an arbitrary and variable patterning. This holographic femtosecond laser processing has advantages of high throughput and high light-use efficiency. A critical issue is to precisely control the intensities of the diffraction peaks of the CGH. We demonstrate some methods for the control of the diffraction peaks. We also demonstrate the laser processing with two-dimensional and three-dimensional parallelism.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.43-45
• /
• 1989

Single mode pulsed incidence dye laser which has TEMoo spatial beam pattern, near gaussian temporal shape and narrow band width(less than 500MHz) has been constructed The improved performance comes as a results of cavity length(~5cm) and definition of optical path by means of longitudinal pumping. Using 1.0X10-4M RH-6G dye, conversion efficiency was approximately 2.2% and tuning range was 548-564nm.

• Journal of the Optical Society of Korea
• /
• v.11 no.4
• /
• pp.192-195
• /
• 2007

A high-conversion efficiency, nanosecond pulsed optical parametric generation and amplification with repetition rate of 20 kHz based on a periodically poled MgO-doped stoichiometric lithium tantalate was presented. Pumped by a Q-switched $Nd:YVO_4$ laser at 1064 nm with a pumping power of 4.8W, the generated output power was 1.6W for the signal and idler waves, achieving a slope efficiency of 50%. Using a seed source at signal wave the amplified signal output-pulse energy reached $65{\mu}J$. The obtained maximum gain was 72.4 dB.

• Journal of the Optical Society of Korea
• /
• v.18 no.6
• /
• pp.732-738
• /
• 2014

Combined optical simulation of the ray-tracing technique and the finite difference time domain method was used to investigate the effect of the emitter orientation and the photonic crystal layer on the outcoupling efficiency (OCE) of bottom-emission type organic light emitting diodes (OLEDs). The OLED with a horizontal emitter exhibited an opposite interference effect to that of one with a vertical emitter, which suggested that the OCE would be very sensitive to the emitter orientation at a fixed emitter-cathode distance. The OLED with a horizontal emitter exhibited much larger OCE than that with a vertical emitter did, which was due to the substantial difference in the radiation pattern along with the different coupling with the surface plasmon excitation. The OCE with a horizontal emitter was increased by approximately 1.3 times by inserting a photonic crystal layer between the indium tin oxide layer and the glass substrate. The present study suggested that appropriate control of the emitter orientation and its combination to other outcoupling structures could be used to enhance the OCE of OLEDs substantially.

• Atmosphere
• /
• v.22 no.2
• /
• pp.175-186
• /
• 2012

In this study, we investigate the effects of elliptical shape of Asian dust particles on the estimation of aerosol optical depth by implementing T-matrix method into WRF/Chem Dust Model. The phase function calculated by assuming elliptical particle shape near $110{\sim}160^{\circ}$ of scattering angle showed about 20 times larger than that calculated by assuming spherical particle shape. Significant difference of extinction efficiency was found with an increase of size parameter and aspect ratio. From the simulations of two Asian dust events occurred on 1 April 2007 and 16 March 2010, we found that the difference of extinction efficiency between elliptical and spherical particle shape was about 5~8%. The aerosol optical depth calculated by assuming elliptical particle shape with 1.6, 1.4 and 1.2 of aspect ratio was about $4.0{\pm}0.5%$, $2.0{\pm}0.2%$, and $1.0{\pm}0.1%$ larger than those estimated by assuming spherical particle shape.

• Current Photovoltaic Research
• /
• v.6 no.1
• /
• pp.1-11
• /
• 2018

Current major photovoltaic (PV) market share (> 60%) is being occupied by the multicrystalline (mc)-silicon solar cells despite of low efficiency compared to single crystalline silicon solar cells. The diamond wire sawing technology reduces the production cost of crystalline silicon solar cells, it increases the optical loss for the existing mc-silicon solar cells and hence its efficiency is low in the current mass production line. To overcome the optical loss in the mc-crystalline silicon, caused by the diamond wire sawing, next generation texturing process is being investigated by various research groups for the PV industry. In this review, the limitation of surface structure and optical loss due to the reflectivity of conventional mc-silicon solar cells are explained by the typical texturing mechanism. Various texturing technologies that could minimize the optical loss of mc-silicon solar cells are explained. Finally, next generation texturing technology to survive in the fierce cost competition of photovoltaic market is discussed.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.6
• /
• pp.88-97
• /
• 1994

We describe the design, fabrication, and performance of the optical fiber-photodiode 1$\times$12 arry module using mesa-type InS10.53T GaS10.47TAS/INP 1$\times$12 PIN photodiode array. We fabricated the PIN PD array for high-speed optical fiber parallel data link optimizing quantum efficiency, operating speed sensitivity from the PIN-FET structure, and electrical AC crosstalk. For each element of the array, the diameter of the photodetective area is 80 $\mu$m, the diameter of the p-metal pad is 90 $\mu$m, and the photodiode seperation is 250 $\mu$m to use Si v-groove. Ground conductor line is placed around diodes and p-metal pads are formed in zigzag to reduce Ac capacitance coupling between array elements. The dark current (IS1dT) is I nA and the capacitance(CS1pDT) is 0.9 pF at -5 V. No signifcant variations of IS1dT and CPD from element to element in the array were observed. We calulated the coupling efficiency for 10/125 SMF and 50/125 GI MMF, and measured the responsivity of the PD array at the wavelength is 1.55 $\mu$ m. Responsivities are 0.93 A/W for SMF and 0.96 A/W for MMF. The optical fiber-PD array module is useful in numerous high speed digital and analog photonic system applications.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.3
• /
• pp.21-29
• /
• 2016

In this paper, optical tracking and analysis was carried out to find the optical properties with respect to various geometric design parameters of collimator lens which is very efficient when collect the light. As a result, a whole, ellipse incident part can obtain a high light efficiency and a narrow beam angle, and angled cylinder incident part is confirmed to obtain high efficiency and a narrow beam angle at a certain height or more. When Transmission part have a specific surface which can reflect the light in forward direction, a good optical properties was confirmed.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.5
• /
• pp.121-125
• /
• 1994

We examine the conventional method of measuring the internal optical loss using the dependence of the reciprocal external quantum efficiency on the cavity length in laser diodes. It is shown that the implicit assumption of constant internal differential quantum efficiency ${\eta}_{id}$, which has been customarily misinterpreted as internal quantum efficiency ${\eta}_{i}$, is not valid for devices with short cavity length. Therefore, for reliable measurments long cavity data should be used.