• Title/Summary/Keyword: optical constant

Search Result 674, Processing Time 0.026 seconds

Experimental Study to Examine Wear Characteristics and Determine the Wear Coefficient of Ductile Cast Iron (DCI) Roll (Ductile Cast Iron (DCI) 롤의 마모 특성 고찰 및 마모계수 도출을 위한 실험적 연구)

  • Byon, Sang-Min
    • Tribology and Lubricants
    • /
    • v.33 no.3
    • /
    • pp.98-105
    • /
    • 2017
  • A pin-on-disk test is performed to measure the wear volume of a ductile cast iron (DCI) roll when it wears down using a high carbon steel and two alloy steels at different sliding velocities between the roll and the material (steel). Normal pressure is set as constant and test temperatures are 400, 500 and $600^{\circ}C$. In addition, thermal softening behavior of the DCI roll is examined using a high-temperature micro-hardness tester and the surface hardness variation of the DCI roll is expressed in terms of temperature and heating time. Based on experimental data, a wear coefficient used in Archard's wear model for each material is obtained. The wear volume is clearly observed when the test temperature is $400^{\circ}C$ and sliding velocity varies. However, it is not measured at temperatures of $500^{\circ}C$ and $600^{\circ}C$ even with variations in sliding velocity. From the optical photographs of the pin and disk, the abrasive wear is observed at $400^{\circ}C$ clearly, but no at $500^{\circ}C$ and $600^{\circ}C$. At higher temperatures, the pin surface is not smooth and has many tiny caves distributed on it. It is found that wear volume is dependent on the carbon contents rather than alloy contents. Results also reveal that the variations of wear coefficients are almost linearly proportional to the carbon contents of the material.

A study on point defect for thermal annealed CuGaSe2 single crystal thin film (열처리된 CuGaSe2 단결정 박막의 점결함연구)

  • 이상열;홍광준
    • Proceedings of the Materials Research Society of Korea Conference
    • /
    • 2003.11a
    • /
    • pp.154-154
    • /
    • 2003
  • A stoichiometric mixture of evaporating materials for CuGaSe2 single crystal thin films was prepared from horizontal electric furnace. Using extrapolation method of X-ray diffraction patterns for the polycrystal CuGaSe2, it was found tetragonal structure whose lattice constant at and co were 5.615 ${\AA}$ and 11.025 ${\AA}$, respectively. To obtain the single crystal thin films, CuGaSe2 mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the hot wall epitaxy (MWE) system. The source and substrate temperatures were Slot and 450$^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (UXD). The carrier density and mobility of CuGaSe2 single crystal thin films measured with Hall effect by van der Pauw method are 5.0l${\times}$10$\^$17/ cm$\^$-3/ and 245 $\textrm{cm}^2$/V$.$s at 293K, respectively. The temperature dependence of the energy band gap of the CuGaSe2 obtained from the absorption spectra was well described by the Varshni's relation, Eg(T) = 1.7998 eV - (8.7489${\times}$10$\^$-4/ eV/K)T$^2$/(T + 335 K. After the as-grown CuGaSe2 single crystal thin films was annealed in Cu-, Se-, and Ca-atmospheres, the origin of point defects of CuGaSe2 single crystal thin films has been investigated by the photoluminescence(PL) at 10 K The native defects of V$\_$CU/, V$\_$Se/, Cu$\_$int/, and Se$\_$int/ obtained by PL measurements were classified as a donors or accepters type. And we concluded that the heat-treatment in the Cu-atmosphere converted CuGaSe2 single crystal thin films to an optical n-type. Also, we confirmed that Ga in CuGaSe2/GaAs did not form the native defects because Ga in CuGaSe2 single crystal thin films existed in the form of stable bonds.

  • PDF

Measurements of the Lidar Ratio for Asian Dust and Pollution Aerosols with a Combined Raman and Back-scatter Lidar (라만-탄성 라이다를 이용한 황사 및 오염 에어러솔의 라이다 비 측정 연구)

  • Yoon, S.C.;Lee, Y.J.;Kim, S.W.;Kim, M.H.;Sugimoto, N.
    • Atmosphere
    • /
    • v.20 no.4
    • /
    • pp.483-494
    • /
    • 2010
  • The vertical profiles of the extinction coefficient, the backscatter coefficient, and the lidar ratio (i.e., extinction-to-backscattering ratio) for Asian dust and pollution aerosols are determined from Raman (inelastic) and elastic backscatter signals. The values of lidar ratios during two polluted days is found between 52 and 82 sr (July 22, 2009) and 40~60 sr (July 31, 2009) at 52 nm, with relatively low value of particle depolarization ratio (<5%) and high value of sun photometer-derived Angstrom exponent (> 1.2). However, lidar ratios between 25 and 40 sr are found during two Asian dust periods (October 20, 2009 and March 15, 2010), with 10~20% of particle depolarization ratio and the relatively low value of sun photometer-derived Angstrom exponent (< 0.39). The lidar ratio, particle depolarization ratio and color ratio are useful optical parameter to distinguish non-spherical coarse dust and spherical fine pollution aerosols. The comparison of aerosol extinction profiles determined from inelastic-backscatter signals by the Raman method and from elastic-backscatter signals by using the Fernald method with constant value of lidar ratio (50 sr) have shown that reliable aerosol extinction coefficients cannot be determined from elastic-backscatter signals alone, because the lidar ratio varies with aerosol types. A combined Raman and elastic backscatter lidar system can provide reliable information about the aerosol extinction profile and the aerosol lidar ratio.

Development of a Low Frequency Accelerometer using the Fiber Bragg Grating Sensor (Fiber Bragg Grating 센서를 이용한 저진동 가속도계 개발)

  • Pack, In-Seok;Kang, Han-Bin;Lee, Kye-Kwang;Lee, Seok-Soon
    • Journal of the Korean Society for Precision Engineering
    • /
    • v.29 no.10
    • /
    • pp.1101-1109
    • /
    • 2012
  • Accelerometers play a key role in the structural assessment. However, the current electric type accelerometers have certain limitations to apply some structures such as heavy cabling labor, installed sea structure and sensitivity to electromagnetic fields. An optical Fiber Bragg Grating (FBG) accelerometer has many advantages over conventional electrical sensors since their immunity to electromagnetic interference and their capability to transmit signals over long distance without any additional amplifiers, and there is no corrosion from sea water. In this paper, we have developed a new FBG-based accelerometer. The accelerometer consists of two cantilevered type beams and a mass and two rollers. A bragg grating element is not directly glued to a cantilever to avoid possible non-uniform strain in the element. Instead, the bragg grating element will be attached to rotation part that rolled inducing vertical movement of the mass and support cantilever beams so that the bragg grating element is uniformly tensioned to achieve a constant strain distribution. After manufacturing, we will prove the performance and the natural frequency of the accelerometer through the experiment with a vibration shaker. The FBG-based accelerometer is developed for measuring the vibration not exceeding 50 Hz for the marine and civil structures.

Morphological study of $SF_6$ clathrate hydrate crystal ($SF_6$ 하이드레이트 결정 성장의 특성)

  • Lee, Yoon-Seok;Lee, Hyun-Ju;Lee, Eun-Kyung;Kim, Soo-Min;Lee, Ju-Dong;Kim, Yang-Do
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 2009.06a
    • /
    • pp.711-711
    • /
    • 2009
  • Global warming has been widely recognized as a serious problem threatening the future of human beings. It is caused by the buildup in the atmosphere of greenhouse gases, such as carbon dioxide, methane, hydrofluorocarbons (HFCs), and sulfur hexafluoride (SF6). Particularly, SF6 has extremely high global warming potential compare to those of other global warming gases. One option for mitigating this greenhouse gas is the development of an effective process for capturing and separating these gases from anthropogenic sources. In general, gas hydrates can be formed under high pressure and low temperature. However, SF6 gas is known to form hydrate under relatively milder conditions. Therefore, technological and economical effects could be expected for the separation of SF6 gas from waste gas mixtures. In this study, we carried out morphological study for the SF6 hydrate crystals to understand its formation and growth mechanisms. The observations were made in high-pressure optical cell charged with liquid water and SF6 gas at constant pressure and temperature. Initially SF6 hydrate formed at the surface between gas and liquid regions, and then subsequent dendrite crystals grew at the wall above the gas/water interface. The visual observations of crystal nucleation, migration, growth and interference were reported. The detailed growth characteristics of SF6 hydrate crystals were discussed in this study.

  • PDF

Effects of Temperature and Humidity on NDIR CO2 Gas Sensor (비분산 적외선 이산화탄소 가스센서 특성의 온·습도 영향)

  • Kim, JinHo;Yi, SeungHwan
    • Journal of Sensor Science and Technology
    • /
    • v.26 no.3
    • /
    • pp.179-185
    • /
    • 2017
  • This article describes the characteristics of nondispersive infrared carbon dioxide gas sensor according to the temperatures and humidifies. In this researches, a thermopile sensor that included application-specific integrated circuit (ASIC) was used and the White-cell structure was implemented as an optical waveguide. The developed sensor modules were installed in gas chamber and then the temperature of gas chamber has been increased from 283 K to 313 K with 10K temperature step. In order to analyze the effects of humidity levels, the relative humidity levels were changed from 30 to 80%R.H. with small humidifier. Then, the characteristics of sensor modules were acquired with the increment of carbon dioxide concentrations from 0 to 2,000 ppm. When the initial voltages of sensors were compared before and after humidifying the chamber at constant temperature, the decrements of the output voltages of sensors are like these: 9mV (reference infrared sensor), 41 mV (carbon dioxide sensor), 2 mV (temperature sensor). With the increment of ambient temperature, the averaged output voltage of carbon dioxide sensor was increased 19 mV, however, when the humidity level was increased, it was decreased 14mV. Based upon the experimental results, the humidity effect could be alleviated by the increment of temperature, so the effects of humidity and temperature could be only compensated by the ambient temperature itself. The estimated carbon dioxide concentrations showed 10% large errors below 200 ppm, however, the errors of the estimations of carbon dioxide concentrations were less than ${\pm}5%$ from 400 to 2,000 ppm.

Characterization of Mungbean (Phaseolus aureus L.) Starch (각종 전분으로 만든 교질상 식품의 특성에 관한 연구 - 녹두 전분의 이화학적 특성 -)

  • Kim, Wan-Soo;Lee, Hei-Soo;Kim, Sung-Kon
    • Applied Biological Chemistry
    • /
    • v.23 no.3
    • /
    • pp.166-172
    • /
    • 1980
  • Starch granules of mungbean observed by microscope and scanning microscope were oval or round, $8{\sim}13{\mu}$ wide, and $18{\sim}30{\mu}m$ long. X-ray diffraction of the starch granules resulted weak crystallinity at $2{\theta}\;16.9^{\circ}$ The blue value of the starch was 0.36, amylose content 22.7%, alkali number 8.52, ferricyanide number 1.06, and water binding capacity of 81.6%. Swelling of the starch was negligible until $50^{\circ}C$, thereafter it increased rapidly. Optical transmittance of 0.3% starch suspension was increased rapidly from $65^{\circ}C$ and the gelatinization at $65{\sim}90^{\circ}C$ was of single stage. Amylogram patterns of the 6.7 and 8% starch solution were similar with no peak viscosity. The time constant for retrogradation of 40% starch gel stored at $21^{\circ}C$ was 1.99 days.

  • PDF

Electro-optic Properties and Thermal Stabilities of Polyimide-DRI Side Chain Polymer for Photonic Devices (폴리이미드-DR1 옆사슬계 전기광학 고분자의 전기광학 특성 및 열적 안정성)

  • Lee, Myeong-Hyeon;Lee, Hyeong-Jong;O, Min-Cheol;An, Ju-Heon;Han, Seon-Gyu
    • Korean Journal of Materials Research
    • /
    • v.9 no.4
    • /
    • pp.355-361
    • /
    • 1999
  • We have synthesized the soluble polymide based side chain system with covalently attached NLO chromophore Disperse Red 1. The developed polymer is optically transparent in the range of optical communication wave-lengths. Its glass transition temperature$(T_g)$ and thermal decomposition temperature$(T_d)$ are $225^{\circ}C, 310^{\circ}C$ respectively. The poled film with the poling field of $100 V/\mu\textrm{m}$ shows that the dielectric constant is 3.37 at the 10-kHz frequency, the refractive indices of TM and TE modes are both 1.631 at $\lambda = 1300 nm$, and the Electro-optic coefficients are 4.6~9.2 pm/V at $\lambda = 1300 nm$. There are no decays of the EO coefficient in the poled polymer at $180^{\circ}C$ in one hour, and $90^{\circ}C$ in 500 hours.

  • PDF

A new analysis on the bleaching mechanism and the catalysis of exposure in holographic diffraction grating fabricated with silver salt (은염 홀로그래픽 회절격자의 제작에서 표백과 노광량의 촉매작용에 관한 새로운 해석)

  • Yun, Byeong-Ho;Kim, Nam
    • Korean Journal of Optics and Photonics
    • /
    • v.7 no.4
    • /
    • pp.314-321
    • /
    • 1996
  • In this paper, the chemical process of each step in fabricating the holographic phase diffraction grating with silver salt sensitive materials has been studied in detail. A new analysis of the bleaching methods have been made through the study. The result shows that among the types of bleaching methods, the reversal bleach can not be reacted chemically. And the experiments about the chemical reactions, the characteristics of the reaction products and the refractive modulation types by the bleaching methods have been done to prove the theory. It is investigated that the exposure acts as the catalyst of developing reaction and affects the developing reaction time conspicuously. At the optimum developing reaction times, which could be taken from the experiments, the holographic diffraction gratings with high diffraction efficiency over 70% could be obtained in the range of the exposure quantity 50~350 [$\mu$J/ $\textrm{cm}^2$]. From the experiments about the correlation of the chemical processing conditions of the composition of developers, the exposure, and the developing reaction time, it has proved that the enhancement of the diffraction efficiency is impossible in the limited exposure energy and conventional constant chemical reaction time.

  • PDF

Growth and characterization of CdTe single crystals by vertical Bridgman method (수직 Bridgman법에 의한 CdTe 단결정의 성장과 특성)

  • 정용길;신호덕;엄영호;박효열;진광수
    • Journal of the Korean Crystal Growth and Crystal Technology
    • /
    • v.6 no.2
    • /
    • pp.220-228
    • /
    • 1996
  • CdTe single crystals were grown by vertical Bridgman method using double furnace with two siliconit heating elements. When the peak temperature of the upper furnace was fixed at $1150^{\circ}C$ and that of the lower furnace was $800^{\circ}C$, the temperature gradient was about $22.5^{\circ}C$/cm. The lattice constant $a_0$ was $6.482\AA$ from the X-ray diffraction and the band gap energy obtained from the optical absorption experiment at room temperature was 1.478 eV. PL spectrum showed that the bound exciton emission peak was resolved into ($A^0,X$) (1.5902, 1.5887 eV), ($h\;D^0$) (1.5918 eV) and ($D^0,X$ (1.5928, 1.5932 eV), and we have also calculated binding energy and ionization energy of the neutral donor and acceptor.

  • PDF