• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.3
• /
• pp.585-593
• /
• 2020

Until now, 29 fire accidents have occurred; 22 of them were caused by the interconnection of renewable energy sources that occurred during the rest period after the lithium-ion battery had been fully charged regardless of the seasons. The fire accidents of ESS were attributed to thermal runaway due to the overcharging of a few cells with the phenomenon of self-energy balancing, which is unintentional current flow from cells with a high SOC to the low cells if the SOC condition of each cell connected in parallel is different. Therefore, this paper proposes a novel configuration and operation algorithm of the BMS to prevent the self-energy balancing of ESS and presents a hybrid SOC estimation algorithm. From the test results of the self-energy balancing phenomenon between aging and normal cells based on the proposed algorithm and BMS, it was confirmed the possibility of self-energy balancing, which is unintentional current flow from cells with a high SOC to cells with a low SOC. In addition, the proposed configuration of the BMS is useful and practical to improve the safety of lithium-ion batteries because the BMS can reliably disconnect a parallel connection of the cells if the self-energy balancing current becomes excessively high.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.3
• /
• pp.129-136
• /
• 2020

A Cut Out Switch (COS) is used for line protection and pole transformer protection in power systems. The COS used to protect the pole transformer is installed on the power side of the pole transformer to protect the electric equipment from fault currents. The COS is composed largely of a body and a fuse holder, and when the fault current is energized, the element of the fuse link in the fuse holder is melted to block the fault current. The arc generated when the COS fuse link is blown causes fire and noise, causing discomfort to residents in the surrounding area, and the arc flame can cause secondary damage to the peripheral device. In this study, a current-limiting COS fuse with improved overcurrent blocking performance rather than explosion type was developed to solve the arc and noise problems during COS operation. The overcurrent breaking performance of the current-limiting COS improves the reliability by developing a striker and COS fuse bracket. In addition, this study aimed to verify the performance of the developed current-limiting COS fuse through a test at an authorized institution.

• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.1
• /
• pp.7-12
• /
• 2009

In this paper, we propose a directional feature extraction method for off-line handwritten numerals by using the morphological operations. Direction features are obtained from four directional line images, each of which contains horizontal, vertical, right-diagonal and left-diagonal lines in entire numeral lines. Conventional method for extracting directional features uses Kirsch masks which generate edge-shaped double line images for each direction, whereas our method uses directional erosion operations and generate single line images for each direction. To apply these directional erosion operations to the numeral image, preprocessing steps such as thinning and dilation are required, but resultant directional lines are more similar to numeral lines themselves. Our four [$4{\times}4$] directional features of a numeral are obtained from four directional line images through a zoning method. For obtaining the higher recognition rates of the handwrittern numerals, we use the multiple feature which is comprised of our proposed feature and the conventional features of a kirsch directional feature and a concavity feature. For recognition test with given features, we use a multi-layer perceptron neural network classifier which is trained with the back propagation algorithm. Through the experiments with the CENPARMI numeral database of Concordia University, we have achieved a recognition rate of 98.35%.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.3
• /
• pp.125-132
• /
• 2018

KVN(Korean VLBI Network) introduced the Mark6 system of the MIT haystack observatory as a recorder for data recording up to 32 Gbps for VLBI(Very Long Baseline Interferometry) observation. The Mark6 recorder can record data at up to 32Gbps when two systems and 64 HDDs are installed. However, because of the unique recording method that is characteristic of Mark6, we are introducing a large amount of data into a virtual file system, or using a general RAID method, which causes data loss when reading and transferring files at the highest recording speed or file system have. The Flexbuff system, a software recorder developed by JIVE(Joint Institute for VLBI ERIC), can be configured to operate as a data recorder through RAID configuration and network upgrades. In particular, when installed in the Mark6 system, it can record VLBI data at a maximum speed of 32 Gbps with less loss of data compared to the existing Mark6 by utilizing Mark6 resources well. In this paper, we propose that the existing Mark6 system can be operated as Mark6-Flexbuff by installing jive5ab software, and it is verified through experiment that it can be effectively used for VLBI observation operation through data recording test.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.5 no.3
• /
• pp.21-29
• /
• 1985

An effective technique of sludge separation is required for concentrated activated sludge process. The dissolved-air flotation (DAF) has been shown to be efficient process for sludge separation. The factors affecting DAF process for activated sludge separation are type and concentration of sludge, air/solid ratio, ratio of pressurized water flow, pressure, sludge detention time, temperature, sludge and hydraulic loading rate, recycle flow rate of sludge and type and quantity of chemical aid. In order to study the optimal operation condition for sludge separation, the influence factors such as type and concentration of sludge, ratio of pressurized water flow and pressure are investigated by the batch and continuous reactor experiments of DAF and sedimentation test. By the experimental investigation, the results are as follows; 1. For the bulking and concentrated sludge, DAF is more effective than sedimentation for the sludge separation. 2. In DAF, the critical ratio of pressurized water flow exist. The critical value varies with the pressure in the tank. That is, according to the pressure changes from 3 to $5kg/cm^2$, the critical value varies from 0.25 to 0.67 accordingly. 3. Pressure affects the ratio of pressurized water flow, but it does not show any influence upon the DAF efficiency directly. 4. Continuous experimental results was not better than those of batch.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.4
• /
• pp.204-209
• /
• 2015

The effluent limit of nickel from electroplating wastewater has been strengthened from 5 mg/L to 3 mg/L from 2014. However, currently applied treatment process for nickel plating wastewater is unable to meet the effluent limit, most of the treatment concept conducted by treatment plant is dilution with other metal bearing wastewater. This can cause very significant impact to the environment of nickel contamination. With this connection, the feasibility test has been conducted with the use of electrolysis by using sacrificial electrodes. Experiments were conducted in synthetic and electroless nickel plating wastewater. Optimal condition of current density, pH were derived from the synthetic wastewater. It was found that the removal efficiency of nickel exceeded 94% at the operation condition of at pH 9 and the current density of $1{\sim}2mA/cm^2$. At this conditions, the iron sludge was generated very low amount. However, it was unsuccessful to meet the effluent limit by applying these treatment conditions to the real electroplating wastewater. This can be explained due to the matrix effect of other metals and anions contained real electroplating wastewater. From the result of further study, the optimal conditions for the real wastewater treatment were found out to be at pH 9, current density $6{\sim}7mA/cm^2$, for 5 minutes of operating time. At these conditions, 88% removal of nickel was achieved, which results the residual nickel concentration was below 3 mg/L.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.10
• /
• pp.1006-1012
• /
• 2008

The effect of small and medium scale shipyard operations on environmental pollutions related with civil appeal of nearby residential areas was estimated. PM-10(particles with an aerodynamic diameter less than or equal to 10 $\mu$m) concentrations were higher, as the sampling sites were nearer from shipyards. PM-10 concentrations of sampling sites closer to shipbuilding companies were higher during the normal operation periods than on vacation at which only small works were done. The larger amount of dry deposition was observed as the sampling sites were closer to shipyards. The odor intensity was highly influenced by ambient temperature. Almost all odor intensities measured by air dilution sensory test went over the emission standard in summer. Odor properties measured by instrumental analysis were observed to exceed the emission standard enforced to the shipyards. Odor compounds such as ammonia, sulfur compounds and trimethylamine went over the standard. Concentrations of styrene and aldehydes were lower than the olfactory threshold. All equivalent sound levels measured at daytime except the value of SP-3 pont were in excess of the environmental standard. Almost all sound levels at nighttime in all measuring sites were higher than the environmental standard. The results of this study shows counterplans need to be established for reducing the civil appeal related pollutions in the research areas.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.9
• /
• pp.654-659
• /
• 2013

This study was conducted to identify an optimal ratio of carbon to nitrogen (C/N ratio) for denitrification of nitrate using molasses as an external carbon source. A series of batch and column tests was conducted using an indigenous bacterium Pseudomonas sp. KY1 isolated from a nitrate-contaminated soil. For the initial nitrate-nitrogen concentration of 100 mg-N/L, batch test results indicated that C/N ratio of 3/1 was the optimal ratio with a relatively high pseudo-first-order reaction constant of $0.0263hr^{-1}$. At C/N ratio of 3/1, more than 80% of nitrate-nitrogen concentration of 100 mg-N/L was removed in 100 hrs. Results of column tests with a flow velocity of 0.3 mL/min also indicated that the C/N ratio of 3/1 was optimal for denitrification with minimizing remaining molasses concentrations. After 172 hrs of column operation (35 pore volumes) with an influent nitrate-nitrogen concentration of 100 mg-N/L, the effluent met the drinking water standard (i.e., 10 mg $NO_3$-N/L).

• Clinics in Shoulder and Elbow
• /
• v.4 no.2
• /
• pp.173-180
• /
• 2001

Aim: To evaluate validity and responsiveness of four shoulder scoring systems. Material and Method: Twenty-five cases of shoulder instability(22 traumatic, 3 non-traumatic) and twenty-three cases of rotator cuff tear(12 small or medium, 10 large or massive) treated surgically were evaluated with the Shoulder Function Score of the University of Pennsylvania(Penn FS), Constant Score, UCLA Shoulder Rating Scale and Simple Shouler Test(SST), preoperatively and at final follow-up. The average follow-up was 16.0 months in instability group and 17.5 months in rotator cuff tear group. Using the SPSS program, Pearson linear correlation coefficiency(PLCC) between the scores were calculated. And to assess the construct validity, PLCC between patients' satisfaction and the scores were also calculated. Responsiveness was measured by the standardized response mean(SRM). Result: In instability group, correlation between the scoring systems was low preoperatively except between Constant and SST, but high after operation. Patients' satisfaction with the scores showed low PLCC preoperativley, but high PLCC postoperatively. SRM was high in PENN and UCLA, but when the satisfaction segment of the score was eliminated from UCLA, the SRM was the lowest. In rotator cuff tear group, there was high correlation between the scores not only preoperatively but postoperatively. And the patients' satisfaction matched well with the scores. SRM was particularly high in UCLA and SST. Even when satisfaction segment was eliminated from UCLA, the SRM was still the highest. Conclusion : Evaluation by the 4 scoring systems investigated in the study showed less consistency in instability than rotator cuff tear in terms of correlation and validity. Responsiveness was generally higher in rotator cuff tear group than in instability group except for Pennsylvania Shoulder Function Score. Therefore it is construed that use of any among the four scoring systems doesn't make difference in evaluation of rotator cuff lesions. However in instability group, care is needed because different result may be obtained according to the selection of a scoring system.

• Journal of Trauma and Injury
• /
• v.25 no.4
• /
• pp.159-165
• /
• 2012

Purpose: For trauma patients, an early-transport and an organized process which are not delayed in hospital stage are necessary. Our hospital developed a procedure, the trauma Critical Pathway (CP), through which a traumatic patient has the priority over other patients, which makes the diagnostic and the therapeutic processes faster than they are for other patients. Methods: The records of patients to whom Trauma CP were applied from January 1, 2011 through April 15. 2012. were reviewed. We checked several time intervals from ER visiting to decision of admission-department, to performing first CT, to applying angio-embolization, to starting emergency operation and to discharging from ER. In addition, outcomes such as duration of ICU stay, hospital stay and mortality were checked and analyzed. Results: The trauma CP was applied to a total of 143 patients, of whom, 48 patients were excluded due to pre-hospital death, ER death, transferring to other hospital and not severe injury. Thus 95 patients (male 64, 67.3%) were enrolled in this study. Fifty-nine patients(62.1%) were injured by the traffic accident. The mortality rate was 10.5% and the mean Revised Trauma Score (RTS) of the patients was $6.4{\pm}2.0$. After visiting ER, decision making for admission was completed, on average, in 3 hours 10 seconds. The mean time intervals for the first CT, angio-embolization, surgery and discharge were 1 hour 20 minutes, 5 hours 16 minutes, 7 hours 26 minutes and 6 hours 13 minutes, respectively. Conclusion: The trauma CP did not show the improvement of time interval outcome, as well as mortality rate. However, this test did show that the trauma CP might be able to reduce delays in procedures for managing trauma patients at the university-based hospitals. To find out the benefit of CP protocol, a large scaled data is required.