• Journal of IKEEE
• /
• v.9 no.1 s.16
• /
• pp.57-64
• /
• 2005

This paper presents a built-in current sensor(BICS) that detects defects in CMOS integrated circuits using the current testing technique. This circuit employs a cross-coupled connected PMOS transistors, it is used as a current comparator. The proposed circuit has a negligible impact on the performance of the circuit under test (CUT) and high speed detection time. In addition, in the operation of the normal mode, the BlCS does not have dissipation of extra power, and it can be applied to the deep submicron process. The validity and effectiveness are verified through the HSPICE simulation on circuits with defects. The area overhead of a BlCS versus the entire chip is about 9.2%. The chip was fabricated with Hynix $0.35{\mu}m$ 2-poly 4-metal N-well CMOS standard technology.

• Journal of Hydrogen and New Energy
• /
• v.14 no.3
• /
• pp.229-235
• /
• 2003

A 50W class MCFC stack was operated in order to test a new design of the circular shaped separator. in the new design, the anode gas was supplied into the stack and was exhausted out of the stack after the anode reaction. The exhausted gas was reacted with the cathode gas supplied with excess oxygen in the vessel in which the stack was placed. Then the reacted gas flowed into the cathode side of the stack and was exhausted through the outlet located in the center of the stack. The average voltage of the single cells in the stack was 0.835V under the current density of $150mA/cm^2$, initially, and the degradation rate of the stack voltage was 1.7%/1,000h. High stack voltage with good stability of the present stack was due to the small temperature gradient in the stack. The small temperature gradient as well as the easiness of temperature control was the result of the new configuration of the separator which utilized the heat of the combustion reaction between anode outlet gas and the cathode inlet gas for heating the stack.

• Journal of Hydrogen and New Energy
• /
• v.23 no.3
• /
• pp.250-255
• /
• 2012

In this paper, the development and performance analysis of a fuel cell-powered unmanned aerial vehicle is described. A fuel cell system featuring 1 kW proton exchange membrane fuel cell combined with a highly pressurized fuel supply system is proposed. For the higher fuel consumption efficiency and simplification of overall system, dead-end type operation is chosen and each individual system such as purge system, fuel supply system, cooling system is developed. Considering that fluctuation of exterior load makes it hard to stabilize fuel cell performance, the power management system is designed using a fuel cell and lithium-ion battery hybrid system. After integration of individual system, the performance of unmanned aerial vehicle is analyzed using data from flight and laboratory test. In the result, overall system was properly operated but for more duration of flight, research on weight lighting and improvement of fuel efficiency is needed to be progressed.

• Journal of Hydrogen and New Energy
• /
• v.22 no.5
• /
• pp.569-578
• /
• 2011

The $SiO_2$ membranes for polymer electrolyte membrane fuel cell (PEMFC) are preapared by electrospinning method. It leads to high porosity and surface area of membrane to accommodate the proton conducting materials. The composite membrane was prepared by impregnating of Nafion ionomer into the pores of electrospun $SiO_2$ membranes. The $SiO_2$:heteropolyacid (HPA) nano-particles as a inorganic proton conductor were prepared by microemulsion process and the particles are added to the Nafion ionomer. The characterization of the membranes was confirmed by field emission scanning electron microscope (FE-SEM), thermogravimetry analysis (TGA), and single cell performance test for PEMFC. The Nafion impregnated electrospun $SiO_2$ membrane showed good thermal stability, satisfactory mechanical properties and high proton conductivity. The addition of the $SiO_2$:HPA nano-particle improved proton conductivity of the composite membrane, which allow further extension for operation temperature in low humidity environments. The composite membrane exhibited a promising properties for the application in high temperature PEMFC.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.4
• /
• pp.1-7
• /
• 2000

In this paper, we study a cause of malfunction of switch to control drive motor in DFMS(Digital Flux Mapping System) which can measure incore neutron flux of the nuclear plant, and develope a method to solve this problem. DFMS has the type of generating contact signal by mechanical switch lever, which is operated whenever thimble detector inserted or withdrawed through thimble Guide Tube. However the characteristics of the lever tend to be changed by mechanical degrade or bad environment and the lever finally generates errotic contact signal. Therefore we installed electric coil ass'yin the outside of Guide Tube instead of mechanical switch assy's. In addition we applied resonance effect to control circuit and installed condenser in the input of power supply to protect noise and interference. After completion of this improvement, we tested this improved device repetitively under the various conditions. In conclusion, we identified the generation of the desired contact signal and the prevention of detector failure through plant surveillance test during normal plant operation.

• Journal of the Korean Institute of Rural Architecture
• /
• v.13 no.3
• /
• pp.73-80
• /
• 2011

This study aims to develop furniture industry in eastern district of Gangwondo and a city of Gangneung and Donghae. Case study on furniture complex in Asahikawa, Japan and survey of furniture companies in Gangneung and Donghae city were implemented for understanding of present state, followed by analysis of problems. It can be summarized as follows. First, the basic operation method of Japanese furniture industry is to keep a balance between industry and academy. Universities or centers are in charge of education and fostering talents, such as allowing to promote and to sell products in design center gallery while corporations support it by lending expensive devices and conducting strength test analysis. Second, according to the survey of furniture companies in Gangneung, many difficulties in products development such as a shortage of designer, method, creative design were discovered. With respect to education and human force fostering, education for design and e-commerce were not sufficient, also marketing section has a problem with limited space for display and selling. Corporate support section is facing problems in receiving raw materials, aging of facilities, manufacturing and management methods. Consequently, it is considered that academic and industrial sections should implement their own roles by forming a bilateral network which connects local universities, high schools, relevant organization in the city and providence and furniture manufacturing companies to companies' product development, human force fostering and marketing in an attempt to activate the furniture industry in this area.

• Journal of Korean Port Research
• /
• v.13 no.2
• /
• pp.245-254
• /
• 1999

This paper aims to derive the strategies for the container terminal in Pusan. So it has focused on analyzing the current conditions of Pusan container terminal while evaluating the difficulties arising from the existing facilities/equipment and the operating system in the Pusan Korea Container Terminal through the workers at the container terminal and at off-dock CY. The object of this study is to assist the existing terminals to operate the facilities/equipment reasonably and to contribute shaping the ports policy which will be the basis of constructing new ports that will remain competitive while maintaining superiority over the ports in northeast area. According to the analysis 68% of the supplier answered that their terminal services which are the most important factor in running a terminal were superior to the other while only 28% of the user answered that they thought the current services were superior. For the areas of supplementing the terminal the people working at the terminal answered in the order of business operation equipment the number of berth service and management ability while the user answered in the order of service computer system transportation system and equipment. According to the regression analysis it became clear that there should be more effort toward improving or supplementing the facility scale facility usage charge transportation facilities which will assist in developing competitiveness of the terminal. It was also noted that management ability and business ability were mentioned as the important factors in operating a terminal.

• Journal of the Korean Institute of Gas
• /
• v.16 no.2
• /
• pp.38-44
• /
• 2012

In recent years, the need for more fuel-efficient and lower-emission vehicles has driven the technical development of alternative fuels such as LPi (Liquid phase LPG injection) which uses pump for the high pressure supply of liquid LPG fuel and is able to meet the limits of better emission levels while it has an advantage of higher power. Although it has the advantage of power and lower emission levels, the characteristics of LPG, such as high vapor pressure, lower viscosity and surface tension than gasoline fuels makes it difficult design system. Therefore most fuel pumps and injectors are imported. In the present study, in order to domestically develop LPG injector which guarantees flow rates and optimal operation, the experimental investigation on leakage and flow rate characteristics of developed prototype injector was carried out at the bench test rig for developed injector.

• Journal of the Korean Institute of Gas
• /
• v.17 no.3
• /
• pp.14-19
• /
• 2013

This paper presents an experimental study on the safety of a valve for a special gas cylinder. The test valves that were randomly dismantled from the special gas cylinder were experimented on the gas leakage and operation safeties. The crack, wear and deformation of the valve body, screw thread, safety disk, vent hole, stem and handle components that may affect to the gas leakage safety of a used valve were not found in this experimental study. A painted handle of a valve was partly stripped from the coated surface, and the surface of PT screw of a used valve body was rusted. But, these paint and rust problems do not affected to the gas leakage safety of used valves. And there was no gas leakage in the dismantled valve, and the permanent deformation and partial scars of a valve stem and O-rings were observed on the rubbing surfaces. Thus, the valve seat and O-rings are recommended to be replaced for a gas leakage safety of a dismantled valve. And it is necessary to repair and inspect handle fastening forces for a safe opening and closing operations of a valve.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.896-897
• /
• 2013

In recent years, logistics tracking Device using GSM & WCDMA to improve logistics efficiency are being extensively researched. The purpose of this paper is to examine the performance development antenna usable cargo container security transport. Antenna developed by study were optimized to match logistics environment apply to GSM & WCDMA dual frequency for monitering system. The measure of antenna have confirmation VSWR is 3:1 measured in return loss -10dB. Reliability of this antenna has been verified about GSM & WCDMA through test-operation between the south korea and Russia.