• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.441-447
• /
• 2002

KSR-III(Korea Sounding Rocket - III), which is being developed by Space Technology R&D Division of KARI(Korea Aerospace Research Institute) will be launched in late 2002. It is a three-stage, liquid propellant rocket which can reach 250 km altitude and will carry out observation of ozone layer and scientific experiments, such as microgravity experiment, and atmospheric measurement. KSR-III is believed to be an intermediate to the launch vehicle capable of carrying a satellite to its orbit. Space Test Department of KARI performed GVT(Ground Vibration Test) fer KSR-III EM at Rocket Test Building of KARI. GVT is very important for predicting the behavior of rocket in its operation, developing flight control program and performing aerodynamic analysis. This paper gives an introduction of rocket GVT configuration and information on test procedures, techniques and results of It. In this test. to simulate free-free condition, test object hung in the air laterally by 4 bungee cords specially devised. For the excitation of test object, pure random signal by two electromagnetic shakers was used and total 22 frequency response functions were achieved. Polyreference parameter estimation was performed to identify the modal parameters with MIMO(Multi-Input-Multi-Output) method. As the result of the test, low frequency mode shapes and modal parameters below 60Hz were identified

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.11
• /
• pp.2832-2839
• /
• 1997

In this paper, a testing architecture and procedure that an idle ATM virtual channel can be utilized for TCP channel is proposed. Four kinds or methodologies for protocol conformance testing have been standardized in ISO. Remote testing method used popularly have some disadvantages that developer must operate system manually in case of System Under Test (SUT) active testing and we cannot control and observe Implementation Under Test (IUT) often. It is proper to adopt distribute testing method than remote test in order to maximize test coverage and optimize fault coverage for conformance testing in ATM systems, and it is required that TCP channel is prepared for distribute testing method. The proposed architecture can adopt distributed testing method without extra physical channel for testing control. Also we can maximize the test coverage and implement the automation of testing without intervention of operator sustaining normal operation of ATM equipment.

• Journal of the Korea Safety Management & Science
• /
• v.17 no.3
• /
• pp.195-204
• /
• 2015

The live fire test has been playing a critical role in evaluating the goals-to-meet of the weapon systems which utilize the power of explosives. As such, the successful development of the test systems therein is quite important. The test systems development covers that of ranges and facilities including system-level key components such as mission control, instrumentation or observation, safety control, electric power, launch pad, and so on. In addition, proper operational guidelines are needed with well-trained test and operation personnel. The emerging weapon systems to be deployed in future battle field would thus have to be more precise and dynamic, smarter, thereby requiring more elaboration. Furthermore, the safety consideration is becoming more serious due to the ever-increasing power of explosives. In such a situation, development of live fire test systems seems to be challenging. The objective of the paper is on how to incorporate the safety and other requirements in the development. To achieve the goal, an architectural approach is adopted by utilizing both the system components relationship and safety requirement when advanced instrumentation technology needs to be developed and deteriorated components of the range are replaced. As an evaluation method, it is studied how the level of maturity of the test systems development can be assessed particularly with the safety requirement considered. Based on the concepts of both systems engineering and SoS (System-of-Systems) engineering process, an enhanced model for the system readiness level is proposed by incorporating safety. The maturity model proposed would be helpful in assessing the maturity of safety-critical systems development whereas the costing model would provide a guide on how the reasonable test resource allocation plan can be made, which is based on the live fire test scenario of future complex weapon systems such as SoS.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.11
• /
• pp.944-951
• /
• 2018

Artificial icing test and wind tunnel test can be performed to reduce the development period when a rotorcraft is required operation under icing situations. Artificial icing test of the KUH(Korean Utility Helicopter) was performed in advance to verify anti-icing and de-icing performance before natural icing test. Although high-precision sensor, the CCP(Cloud Combination Probe) is used to measure icing test condition parameters such as LWC(Liquid Water Content) and MVD(Median Volume Diameter), the measured values need to be verified in various methods due to the possibility of uncertainties which are the test atmosphere environment, sensor errors, and etc. The calculated LWC from the ice thickness cumulated on the fuselage of the KUH is compared to the measured value by CCP, and the results show the effective indirect method to check the test conditions.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.12
• /
• pp.2205-2213
• /
• 2000

To investigate removal efficiency of dissolved matter by NF and RO, a pilot plant was operated for six months using groundwater treated by UF membrane. After the pilot plant operation, we performed autopsy test to identify characteristics of foulant attached on the membrane surface applying the used NF and RO in the pilot plant test. In autopsy test, we measured permeate flux and recovery rate of flux by chemical cleaning in each membrane. We also analyzed chemical cleaning disposal to examine component of foulant. Permeate flux of NF and RO1 showed rapid decline after 100 days of operation. Especially, reduction of specific flux in RO1 was more serious than in NF. Specific flux of RO2 with a low recovery rate resulted in gradual flux decline. Removal efficiencies of dissolved inorganic matters as a conductivity were 76.3%, 88.2% and 95.3% respectively for NF, RO1 and RO2, and RO2 presented the highest removal efficiency. And those of dissolved organic matters as TOC were about 80% for both NF and RO. The specific flux of membranes declined gradually from the feed water inlet to outlet of the membrane module and it showed that membrane fouling increased along the feed flow direction. Namely, concentration of pollutants became higher and volume of feed water was less as the feed flow approached to the outlet. It seemed that major foul ants were Ca consolidated into inorganic material and Si consolidated into organic material on the membrane surface. Fe was a great contribution to irreversible fouling. The SEM results indicated that the organic matter was attached to the first layer, closer to the membrane, and then inorganic matter with tetragonal shape layered over them. We could not observe biofouling because microorganism, which was cause of biofouling, was almost pretreated in UF membrane.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.07a
• /
• pp.25-37
• /
• 2002

The most important industrial application of gamma radiation in characterizing green compacts is the determination of the density. Examples are given where this method is applied in manufacturing technical components in powder metallurgy. The requirements imposed by modern quality management systems and operation by the workforce in industrial production are described. The accuracy of measurement achieved with this method is demonstrated and a comparison is given with other test methods to measure the density. The advantages and limitations of gamma ray densitometry are outlined. The gamma ray densitometer measures the attenuation of gamma radiation penetrating the test parts (Fig. 1). As the capability of compacts to absorb this type of radiation depends on their density, the attenuation of gamma radiation can serve as a measure of the density. The volume of the part being tested is defined by the size of the aperture screeniing out the radiation. It is a channel with the cross section of the aperture whose length is the height of the test part. The intensity of the radiation identified by the detector is the quantity used to determine the material density. Gamma ray densitometry can equally be performed on green compacts as well as on sintered components. Neither special preparation of test parts nor skilled personnel is required to perform the measurement; neither liquids nor other harmful substances are involved. When parts are exhibiting local density variations, which is normally the case in powder compaction, sectional densities can be determined in different parts of the sample without cutting it into pieces. The test is non-destructive, i.e. the parts can still be used after the measurement and do not have to be scrapped. The measurement is controlled by a special PC based software. All results are available for further processing by in-house quality documentation and supervision of measurements. Tool setting for multi-level components can be much improved by using this test method. When a densitometer is installed on the press shop floor, it can be operated by the tool setter himself. Then he can return to the press and immediately implement the corrections. Transfer of sample parts to the lab for density testing can be eliminated and results for the correction of tool settings are more readily available. This helps to reduce the time required for tool setting and clearly improves the productivity of powder presses. The range of materials where this method can be successfully applied covers almost the entire periodic system of the elements. It reaches from the light elements such as graphite via light metals (AI, Mg, Li, Ti) and their alloys, ceramics ($AI_20_3$, SiC, Si_3N_4, $Zr0_2$, ...), magnetic materials (hard and soft ferrites, AlNiCo, Nd-Fe-B, ...), metals including iron and alloy steels, Cu, Ni and Co based alloys to refractory and heavy metals (W, Mo, ...) as well as hardmetals. The gamma radiation required for the measurement is generated by radioactive sources which are produced by nuclear technology. These nuclear materials are safely encapsulated in stainless steel capsules so that no radioactive material can escape from the protective shielding container. The gamma ray densitometer is subject to the strict regulations for the use of radioactive materials. The radiation shield is so effective that there is no elevation of the natural radiation level outside the instrument. Personal dosimetry by the operating personnel is not required. Even in case of malfunction, loss of power and incorrect operation, the escape of gamma radiation from the instrument is positively prevented.

• Journal of the Korean Chemical Society
• /
• v.51 no.6
• /
• pp.549-559
• /
• 2007

The purpose of this study was to investigate cognitive acceleration effect of the experimental group over three years compared with the control group through the ‘Thinking Science' program in the middle school students. The ‘Thinking Science' program was implemented to 168 students in 7th grade over a period of two years. After implementation of the ‘Thinking Science' program, the improvement of formal thinking ability of the students was almost twice examined with SRT VII as the post-test and the delayed test. It was shown that by the end of the implementation period the experimental group had achieved a significantly greater gain score in levels of cognitive development than had the control group. In the subsequent year during which there was no further implementation, the experimental group continued to develop at the same rate as the control group. However, it is clear that much more experimental students in mature concrete operational stage shifted to formal operational stage in delayed test. The results were also analyzed by gender, and cognitive levels of the students. In the post-test, the ratio of girls that shifted to formal operation stage in the experimental group increased as compared with the ratio of boys, while, in the delayed test cognitive level of boys was more effective than that of girls.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.8
• /
• pp.1415-1421
• /
• 2016

There are considerable concern on the methods for the efficient utilization of the test-resources as increasing of the number of the tests for functionality and performance verification of weapon systems. Furthermore, with an increase in the complexity of the resource assignment the decision support is required. Test resource allocation is basically the same problems as conventional NP-hard FJSP(Flexible Job Shop Problem), therefore empirical test resource allocation method that has been used in many decades is limited in the time performance. Although research has been conducted applying the genetic algorithm to the FJSP, it is limited in the test resource allocation domain in which more than one machine is necessary for a single operation. In this paper, a variable group genetic algorithm is proposed. The algorithm is expected to improve the test plan efficiency by automating and optimizing the existing manual based allocation. The simulation result shows that the algorithm could be applicable to the test plan.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.56 no.2
• /
• pp.172-182
• /
• 2020

In order to offer specific information needed to assist in operation of a ship with same type rudder through evaluating the maneuverability of training ship A-Ra with flapped rudder, sea trials based full scale for turning test, zig-zag test with rudder angle 10° and 20°, and spiral test at service condition were carried out on starboard and port sides around Jeju Island according to the standards of maneuverability of IMO. As a result, the angular velocity of port turn was higher than that of starboard turn. Therefore, the size of turning circle was longer on the starboard side. In addition, variation of the transfer due to various factors was more stable than those of the others. In the Z-test results, the mean of 1st and 2nd overshoot angles were 9.8°, 6.3° and 15.3°, 9.2° respectively when the port and starboard was 10°; the 1st overshoot angle were 18°, 13.7° when using 20°. Her maneuverability index T' and K' can be easily determined by using a computer with the data obtained from Z-test where K' and T' are dimensionless constants representing turning ability and responsiveness to the helm, respectively. In the Z-test under flap rudder angle 10°, the obtained K' value covered the range of 2.37-2.87 and T' was 1.74-3.45. Under the flap rudder angle 20°, K' and T' value showed 1.43-1.63, 1.0-1.73, respectively. In the spiral test, the loop width was unstable at +0.3° and -0.5°-0.9° around the midship of flap rudder. As a result, course stability was comparatively good. From the sea trial results, training ship ARA met the present criterion in the standards of maneuverability of IMO.

• Journal of the Korea Society of Computer and Information
• /
• v.13 no.2
• /
• pp.67-78
• /
• 2008

The purpose of this paper is to discuss the design and implementation of a WCBT(Web and Computer based Test). The WCBT combines the strengths of both a WBT(Web-based test) and a CBT(Computer-based test) on the basis of efficiency and stability. The current assessment system, considered an important management tool in the construction and operation of a total management system for the national technical qualification, has some unstable elements with regard to system load and stability. The proposed system's technological aspects have been tested through a basic simulation pilot program. The pilot program will be expanded to include the local Chamber of Commerce and Industry because the stability of the system was proved through its application to the real-time national technical examination of KCCI (Korea Chamber of Commerce and Industry). The WCBT system has shown great efficiency in terms of system load, and has solved frequent communication problems which have occurred through the use of foreign qualifying examinations. The server and client systems of the WCBT have been given good evaluations with regard to the convenience of their use and the management system for operators and supervisors.