• 한국정보전자통신기술학회논문지
• /
• 제13권5호
• /
• pp.359-369
• /
• 2020

본 논문에서는 CMOS X-Ray 검출기의 메인 클럭을 발생시키는 위상 고정 루프(phase locked loop, PLL)을 위한 전류 불일치를 줄이면서도 넓은 동작 범위를 가지는 전하 펌프(charge pump, CP) 회로를 제안하였다. CP 회로의 동작 범위와 전류 불일치는 CP 회로를 구성하는 전류원 회로의 동작 범위와 출력 저항에 의해서 결정된다. 제안된 CP 회로는 넓은 동작 범위를 확보하기 위한 wide operating 전류 복사 바이어스 회로와 전류 불일치를 줄이기 위한 출력 저항이 큰 캐스코드 구조의 전류원으로 구현하였다. 제안된 wide operating range 캐스코드 CP 회로는 350nm CMOS 공정을 이용하여 칩으로 제작되었으며 소스 측정 장치(source measurement unit)을 활용하여 전류 일치 특성을 측정하였다. 이때 전원 전압은 3.3V이고 CP 회로의 전류 ICP=100㎂이었다. 제안된 CP 회로의 동작 범위 △VO_Swing=2.7V이고 이때 최대 전류 불일치는 5.15%이고 최대 전류 편차는 2.64%로 측정되었다. 제안된 CP 회로는 낮은 전류 불일치 특성을 가지면서 광대역 주파수 범위에 대응할 수 있으므로 다양한 클럭 속도가 필요한 시스템에 적용할 수 있다.

• 조명전기설비학회논문지
• /
• 제29권4호
• /
• pp.108-115
• /
• 2015

This paper proposed a optimal current control method to improve efficiency of BLDC motors. The aim of the proposed method is to use the maximum torque operating method by increasing the effective voltage at the maximum torque point unlike existing SPM operating method. The proposed method is based on existing IPM maximum torque operating method grafting onto a square wave operating of SPM motors. As the method of increasing the effective output voltage from inverter using the maximum torque point, the proposed method is to improve efficiency of BLDC motors using the same amount of the existing current effectively. For this method, the maximum torque point is carried out by FEA and analysis of magnetic flux vector. In this paper, the prototype of general-purpose BLDC drive is manufactured and the performance characteristic and validity are verified.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2015년도 전력전자학술대회 논문집
• /
• pp.195-196
• /
• 2015

This paper investigates the design of coupled inductor for minimum inductor current ripple in rapid traction battery charger systems. Based on the general circuit model of coupled inductor together with the operating principles of dc-dc converter, the relationship between the ripple size of inductor current and the coupling factor is derived under the different duty ratio. The optimal coupling factor which corresponds to a minimum inductor ripple current becomes -0.5, i.e. a complete inverse coupling without leakage inductance, as the steady-state duty ratio operating point approaches 1/3 or 2/3. In an opposite manner, the optimal coupling factor value of zero, i.e. zero mutual inductance, is required when the steady-state duty ratio operating point approaches either zero or one. Coupled inductors having optimal coupling factor can minimize the ripple current of inductor and battery current resulting in a reliable and efficient operation of battery chargers.

• 한국초전도ㆍ저온공학회논문지
• /
• 제12권3호
• /
• pp.39-43
• /
• 2010

In Korea, 22.9kV hybrid SFCL (Superconducting Fault Current Limiter) has been developed and carried out long-term field tests in Gochagn power test center of KEPCO through DAPAS program. The SFCL will be installed at a distribution line of Icheon substation in Korea. For the successful application, we have to design the specifications considering real power system operation. This paper proposes a concept of the operating current based rms value for the protection coordination with protective delays and studies a proper range of the current in Korean distribution power system.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2016년도 전력전자학술대회 논문집
• /
• pp.231-232
• /
• 2016

This paper investigates the design of multi-winding coupled inductor for minimum inductor current ripple. Based on the general circuit model of coupled inductor together with the operating principles of dc-dc converter, the relationship between the ripple size of inductor current and the coupling factor is derived under the different duty ratio. The optimal coupling factor of n-phase multi-winding coupled inductor which corresponds to a minimum inductor ripple current becomes -(1/n-1), i.e. a complete inverse coupling without leakage inductance, as the duty ratio of steady-state operating point approaches 1/n, 2/n, ${\cdots}$ or (n-1)/n. In an opposite manner, the optimal coupling factor value of zero, i.e. zero mutual inductance, is required when the duty ratio of steady-state operating point approaches either zero or one. Therefore, coupled inductors having optimal coupling factor can minimize the ripple current of inductor and inductor size.

• Journal of Welding and Joining
• /
• 제15권5호
• /
• pp.84-91
• /
• 1997

The metal transfer phenomenon of the pulsed-GMAW is simulated by formulating the electromagnetic force incorporated with the Volume of Fluid algorithm. The free surface profiles, pressure and velocity distributions within the drop are computed numerically. Axial velocity and acceleration generated during peak current period are found to have a significant effect on drop detachment. Therefore, the accelerated inertia force becomes one of important factors affecting metal transfer in the pulsed-GMAW. When the pulse current parameters are selected properly, the molten drop is detached just after current pulse, and the operating range of the pulsing frequency increases with higher peak current and duty cycle. Calculated operating ranges show reasonably good agreements with the available experimental data.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권6호
• /
• pp.810-817
• /
• 2014

An on-chip current sensor with fast response time for the peak-current-mode buck regulator is proposed. The initial operating points of the peak current sensor are determined in advance by the valley current level, which is sensed by a valley current sensor. As a result, the proposed current sensor achieves a fast response time of less than 20 ns, and a sensing accuracy of over 90%. Applying the proposed current sensor, the peak-current-mode buck regulator for the mobile application is realized with an operating frequency of 2 MHz, an output voltage of 0.8 V, a maximum load current of 500 mA, and a peak efficiency of over 83%.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2004년도 추계 총회 및 학술발표회
• /
• pp.263-266
• /
• 2004

An experimental study was carried out on the recovery of ammonium lactate from simulated fermentation brothby desalting electrodialysis (DSED). All experiments, using AM-1 and CM-1 membranes, were operated in a constant current and a subsequent constant-voltage mode, and the switching point was determined based on the previous results. The effects of operating conditions such as operating current, initial feed concentration, and initial feed pH were investigated. Increased operating current resulted in a decreased operating time but an increased energy consumption per unit amount of ammonium lactate recovered. As the initial feed concentration was increased, the operating time increased while energy consumption decreased. The operating time and energy consumption slightly decreased as the initial feed pH was increased up to 6.0. However, no significant influences on the recovery of ammonium lactate were observed over 6.0. The rejections of acetate, glucose, and proteins were $10\%,\;93\%,\;and\;98\%$, respectively. Sulfate was not rejected at all.

• 대한전기학회논문지
• /
• 제36권8호
• /
• pp.539-546
• /
• 1987

In case of operating at Variable speed the induction motor by a frequency transformer, it will cause ripples in motor torque and considerably bad effects on the machines because the output side of the frequency transformer involves a great number of harmonics. This paper Presents the methods of decreasing torque ripples in induction motor and of improving current waveform, by means of forming the waveforms of output current into multi-step waveforms similiar to sinusoid, and also by means of eliminating the harmonic components maximally, in case of operating a 18-phase multi-inverter combining 3-step current source inverter.

• 품질경영학회지
• /
• 제39권4호
• /
• pp.500-506
• /
• 2011

Evolutionary operation (EVOP) proposed by Box(1957) is a method for continuous monitoring and improvement of a full-scale manufacturing process with the objective of moving the current operating conditions toward the better ones. EVOP in experiments with mixtures consists of screening vital few components and making small changes in the current operating condition by making small increments in the proportion of the screened component. In this paper, how to determine operating conditions in EVOP in experiments with mixtures around the current operating condition is proposed. The proposed methods are illustrated with the simulated data based on the well known flare experimental data described by McLean and Anderson(1966).