• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.464-468
• /
• 2008

In most of the passenger side airbag door in hard type IP today is designed with invisible tear-seam line. In order to design the tear-seam invisible, the tear-seam must be designed with required RWT (residual wall thickness) that is just thick enough to be broken by the PAB pressure on deployment and not by other surrounding impact forces. Hence, keeping the right optimum opening force is very important, and finding the right RWT became the key in designing the tear-seam. The study conducted in this paper describes the search for the optimum RWT around the tear-seam by using finite element method and the optimum RWT is suggested for milling type tear-seam having V-shape cross-section.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.3
• /
• pp.351-356
• /
• 2004

Selected MPEG-b-PDLLA block copolymers have been synthesized by ring-opening polymerization with systematic variation of the chain lengths of the resident hydrophilic and hydrophobic blocks. The size and shape of the micelles that spontaneously form in solution are then controlled by the characteristics of the block copolymer template. All the materials prepared in this study showed the tunable pore size of 20-80 ${\AA}$ with the increase of hydrophobic chain lengths and up to 660 $m^2$/g of specific surface area. The formation mechanism of these nanoporous structures obtained by controlling the micelle size has been confirmed using both liquid and solid state $^{13}C\;and\;^{29}Si$ NMR techniques. This work verifies the formation mechanism of nanoporous structures in which the pore size and wall thickness are closely dependent on the size of hydrophobic cores and hydrophilic shells of the block copolymer templates.

• Structural Engineering and Mechanics
• /
• v.26 no.3
• /
• pp.231-250
• /
• 2007

The influence of masonry infills with eccentric openings on the seismic performance of reinforced concrete (r/c) frames that were designed in accordance with current code provisions are investigated. Eight 1/3-scale, single-story, single-bay frame specimens were tested under cyclic horizontal loading up to a drift level of 4%. In all examined cases the shear strength of columns was higher than the cracking shear strength of solid infill. The parameters investigated include the shape and the location of the opening. Assessment of the behavior of the frames is also attempted, based on the observed failure modes, strength, stiffness, ductility, energy dissipation capacity and degradation from cycling loading. Based on these results there can be deduced that masonry infills with eccentrically located openings has been proven to be beneficial to the seismic capacity of the bare r/c frames in terms of strength, stiffness, ductility and energy dissipation. The location of the opening must be as near to the edge of the infill as possible in order to provide an improvement in the performance of the infilled frame.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.9
• /
• pp.96-102
• /
• 2009

In this study, performs analysis of the life of parallel opening type pneumatic chucks that are usually applied in the factory automation line. Pneumatic chucks have complicated failure cause because they are organized as a complex of various elements. Therefore, we analyzed the main failure mode of pneumatic chuck, and then performed life test and performance test according to the international standards. On the basis of these processes, shape parameter of pneumatic chuk is proposed that is the main factor for the calculation of zero failure test time for the reliability of pneumatic chuck and their data analysis of life distribution.

• Journal of Biosystems Engineering
• /
• v.20 no.4
• /
• pp.351-359
• /
• 1995

In pressure cooling system, produce were packed in vented box and cooled rapidly by producing a difference in air pressure on opposite faces of stacks of vented box. So, energy requirements and performance of pressure cooling system depended upon the air flow rate and the static pressure drop through packed produce in vented box. The static pressure drop across packed produce in vented box normally depended upon air flow rate, vent area of box and conditions of produce bed (depth, porosity, stacking patterns, size and shape of products) in box. The objectives of this study were to investigate the effect of vent area and air flow rate on airflow resistance of empty box and packed produce in vented box, and to investigate the relationship between the air flow resistance of packed products in vented box and sum of air flow resistance of empty box only and products in bulk only. Mandarins and tomatoes were used in the experiment. The airflow rate were in the range of 0.02~1.0$m^3$/s.$m^2$, the opening ratio of vent hole were in the range of 2.5~20% of the side area. The results were summerized as follows. 1. The pressure drops across vented box increased in proportion to superficial air velocity and decreased in proportion to opening ratio of vent hole. A regression equation to calculate airflow resistance of vented box was derived as a function of superficial air velocity and opening ratio of vent hole. 2. The pressure drops across packed produce in vented box increased in proportion to superficial air velocity and decreased in proportion to opening ratio of vent hole. 3. Because of the air velocity increase in the vicinity of vent hole in box, the airflow resistances of packed products in vented box were always higher than sum of air flow resistance of empty box only and products in bulk only. 4. Based on the airflow resistance of empty box and products in bulk, a regression equation to calculate airflow resistance of packed products in vented box was derived.

• Journal of the Ergonomics Society of Korea
• /
• v.20 no.2
• /
• pp.83-97
• /
• 2001

Korea has become an aged society according to the UN specifications. The number of the aged population will increase drastically, and the number of single aged people will also increase. Products used in our daily life are manufactured within the normal capabilities of people. Thus, aged people have encountering problems in using them. Numerous products are used in our daily lives. The purpose of this study is to find the acceptable torque for aged people to open the caps of processed food containers. Depending on the size and shape of the opening hand, hand operation has been classified into three categories. A total of one hundred and nine people participated in this study. Fifty nine people in the 20-30 year old range and fifty people in their 60-70's. Results of the study are as follows: 1) For all categories the acceptable cap torque data for the aged people are established. To satisfy 95% of the aged people, it was found that $74N{\cdot}cm$ for type A caps, and $141N{\cdot}cm$ for B type caps. and $214N{\cdot}cm$ for type C were the acceptable torque levels. 2) The appropriate level of torque for opening the cap was found to be 70% of the maximum torque for the aged people.(71.4% for type A. 71.4% for type B. 72.2% for type C). 3) Capabilities of the 70's drops sharply in function related to opening cap (maximum torque, gripping force, and wrist movement range). 4) Among aged subjects, 65.0% for type A, 42.0% for type B, and 68.8% for type C, had difficulties in opening the container caps.

• Steel and Composite Structures
• /
• v.22 no.6
• /
• pp.1417-1443
• /
• 2016

Cellular and castellated steel beams are used to obtain higher stiffness and bending capacity using the same weight of steel. In addition, the beam openings may be used as a pass for different mechanical fixtures such as ducts and pipes. The aim of this study is to investigate the effect of different parameters on both elastic and inelastic critical buckling stresses of steel web plates with openings. These parameters are plate aspect ratio; opening shape (circular or rectangular); end distance to the first opening; opening spacing; opening size; plate slenderness ratio; steel grade; and initial web imperfection. The web/flange interaction has been simplified by web edge restraints representing simply supported boundary conditions. A numerical parametric study has been performed through linear and nonlinear finite element (FE) models, where the FE results have been verified against both experimental and numerical results in the literature. The web plates are subject to in-plane linearly varying compression with different loading patterns, ranging from uniform compression to pure bending. A buckling stress modification factor (${\beta}$-factor) has been introduced as a ratio of buckling stress of web plate with openings to buckling stress of the corresponding solid web plate. The variation of ${\beta}$-factor against the aforementioned parameters has been reported. Furthermore, the critical plate slenderness ratio separating elastic buckling and yielding has been identified and discussed for two steel grades of DIN-17100, namely: ST-37/2 and ST-52/3. The FE results revealed that the minimum ${\beta}$-factor is 0.9 for web plates under uniform compression and 0.7 for those under both compression and tension.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.94-103
• /
• 2018

The purpose of designing composite lattice structure which applied to launching vehicle and tactical missile body is to minimize the thickness and weight for applied load. It is usually made of carbon fiber; fabricating with filament winding process over silicon mold, and provided with a window opening for inspection purpose if necessary. In this paper compression test is conducted without window opening in lattice structure and preliminary FEA is carried out to confirm its accuracy. And then FEA is performed for the case of window opening to evaluate the soundness and the safety factor of the structure. We have calculated for two kinds of window shape; rectangular one and hexagonal one. And we have calculated safety factors of the lattice structure with window opening in every case based on failure strength of rib and knot with varying the thickness and location of the window for hexagonal shape. Through our investigation, we have found out the followings; (1) the hexagonal shaped window is shown higher safety factor than rectangular one, (2) a window in a certain location is shown higher safety factor than others, (3) although the soundness of window structure is improved as increasing its thickness, a window of a certain thickness is shown higher safety factor than others because of stress concentration.

• The Research Journal of the Costume Culture
• /
• v.23 no.3
• /
• pp.439-453
• /
• 2015

This research is regarding Park Ki-Jong's Western-style court costume and emphasizes the shape and style peculiarities of Western-style court costumes in the Korean Empire from the 1876 Port Opening to the 1910 annexation of Korean to Japan. Park Ki-Jong's frock coat was made during the period of the established law from 1900 to 1910. 1) The brand was ASADA TAILOR from Kyung-Sung. 2) The shape was long at the front and back, and it featured a picked lapel and double breast with six buttons to fasten and two buttons for decoration on the upper part. 3) The frock coat's materials were black wool fabric and black ridged silk. The lining's material was black plain silk and the sleeve's lining was white with blue striped silk. 4) The front separated the upper and bottom parts. The bottom was composed of a one-piece A-line skirt that continued from the front to back. The top of the back was separated by the princess line and the center-back seam was also separated with a vent. However, the center-back of the waistline was not separated, and it continued to one piece. The sleeve shape was a two-piece sleeve style with a phony vent and two wrapping buttons.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.617-623
• /
• 1990

Cracks present in pressure vessels have been reported to be mostly semi-elliptic surface cracks. The fatigue crack growth rates(FCGR) of surface cracks in the pressure vessel materials, API5A-K55 and SPV 500, used in this study were showed to be different depending on the direction of propagation of the surface crack. An equation for the prediction of the shape change of the surface crack was obtained by combining the Paris' relations for each direction of surface crack extension and agreed well with the experimental data. And also FGGR in both materials were evaluated and prediction of the shape change of surface crack were made using averaged stress intensity factor.