• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1993.10a
• /
• pp.83-88
• /
• 1993

This paper persents the measurement method using a spinning cylinder system for stream-ing electrification of transformer oil. The spinning cylinder system has a simple mechan-ical construction, and requires less oil com-pared to the other methods. Alse, the effects of various admixtures on the static electri-fication and properties of tranformer oil can be easily investigated. Experiments showed that addition of the BTA reduced the streaming electrification and the polarity of static electrification wasconver-ted to negative at 50 ∼ 70[ppm] of BTA

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.46 no.4
• /
• pp.383-390
• /
• 2020

Blue light is a blue-based light existing at a wavelength between 380 and 450 nm, and it has been reported that it induces active oxygen and causes aging, and accordingly, interest in the blue light blocking effect is increasing. In this study, the effects of the polarity of oil, viscosity of the formulation, type of emulsifier, emulsified particles, and inorganic UV blocking agents on the blue light blocking effect in UV blocking products were investigated. As a result, it was confirmed that the blue light blocking rate increased as the polarity of the oil became similar to that of the organic UV blocker, and the higher the viscosity of the formulation, the higher the blue light blocking rate. The types of emulsifiers and emulsified particles had little effect on the blue light blocking effect, and the presence of inorganic UV blocking agents was found to be one of the factors that greatly influenced the blue light blocking rate. These results can effectively increase the efficiency of blocking blue light, and may be used in the development of blue light blocking products and formulation research in the future.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.1
• /
• pp.42-47
• /
• 2010

Polymer insulating materials such as cross linked polyethylene (XLPE) are employed in electric cables used for extra high voltage. These materials can degrade due to chemical, mechanical and electric stress, possibly caused by voids, the presence of extrinsic materials and protrusions. Therefore, this study measured discharge patterns, discharge phase angle, quantity and occurrence frequency as well as changes in XLPE under different temperatures and applied voltages. To quantitatively analyze the irregular partial discharge patterns measured, the discharge patterns were examined using a statistical program. A three layer sample was fabricated, wherein the upper and lower layers were composed of non-void XLPE, while the middle layer was composed of an air void and copper particles. After heating to room temperature and $50^{\circ}C$ and $80^{\circ}C$ in silicone oil, partial discharge characteristics were studied by increasing the voltage from the inception voltage to the breakdown voltage. Partial discharge statistical analysis showed that when the K-means clustering was carried out at 9 kV to determine the void discharge characteristics, the amount discharged at low temperatures was small but when the temperature was increased to $80^{\circ}C$, the discharge amount increased to be 5.7 times more than that at room temperature because electric charge injection became easier. An analysis of the kurtosis and the skewness confirmed that positive and negative polarity had counterclockwise and clockwise clustering distribution, respectively. When 5 kV was applied to copper particles, the K-means was conducted as the temperature changed from $50^{\circ}C$ to $80^{\circ}C$. The amount of charge at a positive polarity increased 20.3% and the amount of charge at a negative polarity increased 54.9%. The clustering distribution of a positive polarity and negative polarity showed a straight line in the kurtosis and skewness analyses.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.6
• /
• pp.288-291
• /
• 2010

Accidents can occur as a result of streaming electrification when transformer oil is used as an insulating oil in large ultra-high voltage transformers. Methods for adding a streaming electrification inhibitor to reduce the streaming electrification has been studied extensively. In this paper, in order to develop a method for reducing streaming electrification effectively, 4 different specimens were prepared by the addition of benzotriazole (BTA) to a virgin specimen with constant stirring. The specimens were examined to determine the appropriate amount of BTA addition that would suppress the streaming electrification most effectively. The results showed that the streaming electrification characteristics of the specimen in the streaming transformer oil were best when the amount of BTA addition was about 10 ppm. The streaming electrification current was reduced by adding 30 ppm BTA until the temperature reached $65^{\circ}C$. The polarity of the streaming electrification current was negative when the temperature exceeded $65^{\circ}C$. Therefore, the streaming electrification current, which can be a cause of transformer accidents, can be suppressed in large ultra high voltage transformer oil. This paper reports on the optimal amount of BTA addition and the best conditions for controlling the streaming velocity of transformer oil.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.6
• /
• pp.66-71
• /
• 2011

Various single solvents were tested to find the effective solvent for the extraction of algae oil from wet-form Chlorella minutissima. In the case of single solvents, their extractabilities for algae oil were increased with their polarity because the water in wet algae cell is to form a solvent shell around the lipids. Based on these results, the wet-form algae samples were treated with a polar alcohol solvent and then a nonpolar solvent was added in algae residue. In the algae oil extraction by ethanol/n-hexane, total lipid contents were 40-50% and composition of triglyceride in extracted oil was 46.50%. Considering solvent toxicity of conventional solvent mixture such as chloroform and methanol for algae oil extraction, the ethanol/n-hexane system was identified as the effective one for the oil extraction from wet-form Chlorella minutissima.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.170-172
• /
• 1990

In a large power transformer, an insulating oil is forced to circulate for cooling the heat generated by the losses within the windings and core. When oil flows and rubs against various materials, including insulating paper and steel, electrostatic charges are separated at the interface of the oil and the solid material. This paper considers the polarity and the streaming electrification of the various materials which are used in transformer. As a result of this study, it is confirmed that the leakage current on the solid material, such as paper, is charged negative. On the other hand, the solid material, such as steel, is positively charged.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1478-1480
• /
• 1997

We investigated the breakdown characteristic of mineral oil according to applied voltage and tip radius. In this experiment, electrode system was point-plane geometry. The tip radius of needle was 5, 10, 20 and $25{\mu}m$, respectively. Applied voltage was AC and DC. We measured breakdown voltage for each tip radius with increasing electrode gap, 2mm to 10mm. Under nonuniform electric field, breakdown strength was higher when needle was negative than when needle was positive. Because it is polarity effects due to space charge. And the more sharp tip radius, whether we applied AC or DC, the higher breakdown strength. As tip radius increase, breakdown strength decreases exponentially.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.25 no.1
• /
• pp.137-155
• /
• 1999

The o/w emulsions were prepared by lysolecithin as a biosurfactantsto to emulsify oils with squalane(SQ), liquid paraffin(LP), octylpalmitate(OP), octylstearate(OS), alkyl benzoate(AB), isostearyl benzoate(ISB). The droplets size and shape of o/w emulsions were investigated by laser light scattering, With dynamic light scattering hydrodynamic radius(Rh) of emulsion droplets was varied from 150m to 250m and critical concentration of oil In which the hydrodynamic radius(Rh) of emulsion droplets decreased and increased was found in the point of 0.5wt% oil concentration, and it was found increasing the polarity of oil deccreased the droplets, the droplets size of SQ(polar oil) were lower than SQ(nonpolar oil) With static light scattering radius of gyration(R$_{g}$) of emulusion droplets was to be calculated. From measurements of the ratio of R$_{g}$R$_{h}$ it was found that the shape of droplet of ISB, AB(polar oils) were sphere, for OP, OS(apolar oil) were oblate, for LP, SQ(nonpolar oil) were rod. The viscosity of emulsion in the form of rod was higher than that of emulsion in the form of sphere.e.e.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.254-257
• /
• 1997

In this paper, we investigated the effects of gap length and tip radius influenced in breakdown of mineral based insulation oil Electrode system was needle-plane geometry It is to model conductive extrusions in oil filled electrical power apparatus. The tip radius of needle electrode was 5, 10, 20 and 25${\mu}{\textrm}{m}$, respectively. We measured breakdown voltage for each of tip radius with increasing electrode gap, 2mm to 12mm. It was calculated electrical breakdown strength at tip using Mason\`s equation from breakdown voltage As gap lenght increased. breakdown strength increased linearly. But, as tip radius of needle increased, breakdown strength decreased exponentially. It can be explained by tole phenomenon that electron is easily injected, as tip radius increases, and effective work function decreases. When appling DC voltage. breakdown 7tr7ilgtll was higher wheal polarity of needle was negative than positive. It is because of the space charge effect ill accordance with the influence of liquid motion.

• Journal of the Korean Society of Safety
• /
• v.19 no.1
• /
• pp.56-59
• /
• 2004

In this paper, we investigated the influence of gap length and tip radius on breakdown of mineral based insulation oil. Applied voltages were DC and AC voltage. Electrode system was needle-plane structure. The tip radius of needle electrode was 5, 10, 20 and 25${\mu}m$, respectively. We measured breakdown voltage for each of tip radius with increasing electrode gap, 2mm to 12mm. Electric breakdown strength at tip was calculated using Mason's equation contained geometric figure. As gap length increased, breakdown strength increased linearly. But, as tip radius of needle increased, breakdown strength decreased exponentially. It can be explained by the phenomenon that electron is easily injected, as tip radius increases, and effective work function decreases. When appling DC voltage, breakdown strength was higher when polarity of needle was negative than positive. It is because of the space charge effect in accordance with the influence of liquid motion.