• Ocean Systems Engineering
• /
• v.6 no.4
• /
• pp.377-400
• /
• 2016

Dropped objects are among the top ten causes of fatalities and serious injuries in the oil and gas industry (DORIS, 2016). Objects may accidentally fall down from platforms or vessels during lifting or any other offshore operation. Proper planning of lifting operations requires the knowledge of the risk-free zone on the sea bed to protect underwater structures and equipment. To this end a three-dimensional (3D) theory of dynamic motion of dropped cylindrical object is expanded to also consider ocean currents. The expanded theory is integrated into the authors' Dropped Objects Simulator (DROBS). DROBS is utilized to simulate the trajectories of dropped cylinders falling through uniform currents originating from different directions (incoming angle at $0^{\circ}$, $90^{\circ}$, $180^{\circ}$, and $270^{\circ}$). It is found that trajectories and landing points of dropped cylinders are greatly influenced by the direction of current. The initial conditions after the cylinders have fallen into the water are treated as random variables. It is assumed that the corresponding parameters orientation angle, translational velocity, and rotational velocity follow normal distributions. The paper presents results of DROBS simulations for the case of a dropped cylinder with initial drop angle at $60^{\circ}$ through air-water columns without current. Then the Monte Carlo simulations are used for predicting the landing point distributions of dropped cylinders with varying drop angles under current. The resulting landing point distribution plots may be used to identify risk free zones for offshore lifting operations.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.12
• /
• pp.1535-1548
• /
• 2004

Condensation heat transfer experiments were conducted with the oblong shell and plate heat exchanger without oil in a refrigerant loop using R-l34a, R-407C and R-410A. An experimental refrigerant loop has been developed to measure the condensation heat transfer coefficient h$_{r}$ and frictional pressure drop $\Delta$p$_{f}$ of the various refrigerants in a vertical oblong shell and plate heat exchanger. The effects of the refrigerant mass flux(40∼80kg/$m^2$s), average heat flux(4∼8kW/$m^2$), refrigerant saturation temperature(30∼4$0^{\circ}C$) and vapor quality of refrigerants on the measured data were explored in detail. Similar to the case of a plate heat exchanger, even at a very low Reynolds number, the flow in the oblong shell and plate heat exchanger remains turbulent. A comparison of the performance of the various refrigerants revealed that R-410A had the highest heat transfer performance followed by R-l34a, and R-407C had the lowest performance of the refrigerants tested. The pressure drops were also reported in this paper. The pressure drops for R-410A were approximately 45% lower than those of R-l34a. R-407C had 30% lower pressure drops than R-l34a. Experimental results were compared with several correlations which predicted condensation heat transfer coefficients and frictional pressure drops. Comparison with the experimental data showed that the previously proposed correlations gave unsatisfactory results. Based on the present data, empirical correlations of the condensation heat transfer coefficient and the friction factor were proposed.tor were proposed.sed.

• Korea-Australia Rheology Journal
• /
• v.19 no.3
• /
• pp.157-164
• /
• 2007

Microencapsulation of cells within microfluidic devices enables explicit control of the membrane thickness or cell density, resulting in improved viability of the transplanted cells within an aggressive immune system. In this study, living cells (3T3 and L929 fibroblast cells) are encapsulated within a semi-permeable membrane (calcium crosslinked alginate gel) in two different device designs, a flow focusing and a core-annular flow focusing geometry. These two device designs produce a bead and a long microfibre, respectively. For the alginate bead, an alginate aqueous solution incorporating cells flows through a flow focusing channel and an alginate droplet is formed from the balance of interfacial forces and viscous drag forces resulting from the continuous (oil) phase flowing past the alginate solution. It immediately reacts with an adjacent $CaCl_2$ drop that is extruded into the main flow channel by another flow focusing channel downstream of the site of alginate drop creation. Depending on the flow conditions, monodisperse microbeads of sizes ranging from $50-200\;{\mu}m$ can be produced. In the case of the microfibre, the alginate solution with cells is extruded into a continuous phase of $CaCl_2$ solution. The diameter of alginate fibres produced via this technique can be tightly controlled by changing both flow rates. Cell viability in both forms of alginate encapsulant was confirmed by a LIVE/DEAD cell assay for periods of up to 24 hours post encapsulation.

• Applied Chemistry for Engineering
• /
• v.22 no.4
• /
• pp.376-383
• /
• 2011

The CMCs of LA and LA3 nonionic surfactants obtained from the reaction between glycidol and lauryl alcohol were found to be $0.97{\times}10^{-3}mol/L$ and $1.02{\times}10^{-3}mol/L$ respectively and the surface tensions for 1 wt% surfactant were 26.99 and 27.48 mN/m respectively. Dynamic surface tension measurements using a maximum bubble pressure tensiometer showed that the adsorption rate of surfactant molecules at the interface between the air and the surfactant solution was found to be relatively fast in both surfactant systems, presumably due to the high mobility of surfactant molecules. The contact angles of LA and LA3 nonionic surfactants were 27.8 and $20.9^{\circ}$ respectively and the dynamic interfacial tension measurement by a spinning drop tensiometer showed that interfacial tensions at equilibrium condition in both systems were almost the same. Also both surfactant systems reached equilibrium in 2~3 min. Both surfactant solutions showed high stability when evaluated by conductometric method and the LA nonionic surfactant system provided the higher foam stability than the LA3 nonionic surfactant system. The phase behavior experiments showed a lower phase or oil in water (O/W) microemulsion in equilibrium with an excess oil phase at all temperatures studied. No three-phase region was observed including a middle-phase microemulsion or a lamellar liquid crystalline phase.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.26 no.1
• /
• pp.29-38
• /
• 2008

Print-through is one of the most important attributes of print quality and has long been a subject to study. However, some aspects of print through are still in need to be enlighten. In this paper, different kinds of evaluating methods for print through are compared using densitometry, brightness, and image analysis. Printing conditions including ink feed, drying condition, and emulsification rate are systematically changed to effect print-through both on uncoated and coated commercial papers. Also several inks from different makers are introduced and compared in terms of print-through propensity. From the results, densitometry is not a good indicator for print through on the papers in this study. Ink feed has a strong effect on print through, especially for uncoated paper and should be considered in a point of optimum ink feed level in real world. Contribution of faster ink(oil) absorption seems to be more competitive than that of ink(oil) evaporation resulting in severer print-through for hot drying process. It is shown that ink-water emulsification rate increases print through at mild level but easy to decrease it with lower density due to the increase of water contents in emulsion. It is believed that the effect of absorption overwhelms that of density drop at mild emulsification level. This study does not include the effect of ink attributes in detail but shows that distinctive differences in print through may be resulted from various ink-makers and is finalized with some suggestions.

• Korean journal of applied entomology
• /
• v.8
• /
• pp.25-28
• /
• 1969

In order to find out the effect of contactor to form appressorial structure of Glomerella glycines, this experiment was carried out by using several contactors such as cover glass. cellophane, vinyl and oil paper respectively. In the case of cover glass placed on a drop of conidial suspension of the fungus which is incubated on water agar for 12 hours, 67.7 percent of appressoria were resulted, whereas no appressorial structure was found in the control. Vinyl was known best physical contactor and cellophane, cover glass and oil paper were fairly good in that order. Effects of temperature, time and relative humidity on the formation of appressoria of G. glycines were similar to each of optimum growth range of temperature and relative humidity $25^{\circ}-30^{\circ}C$ and 70-100 Percent, respectively. In addition, maximum appressorial formation was resulted in the conidial suspension incubated on soybean leaves for 36 hours. No appressorium was found at above $35^{\circ}C$, below R.H. 70 percent and 5 hours incubation.

• Advances in materials Research
• /
• v.4 no.4
• /
• pp.215-226
• /
• 2015

Experiment on roughness and micro pit defects of SUS 430 ferrite stainless steel was investigated in laboratory. The relation between roughness and glossiness with reduction in height, roll surface roughness, emulsion parameters was analyzed. The surface morphology of micro pit defects was observed by SEM, and the effects of micro pit defects on rolling reduction, roll surface roughness, emulsion parameters, lubrication oil in deformation zone and work roll diameter were discussed. With the increasing of reduction ratio strip surface roughness Ra(s), Rp(s) and Rv(s) were decreasing along rolling and width direction, the drop value in rolling direction was faster than that in width direction. The roughness and glossiness were obtained under emulsion concentration 3% and 6%, temperature $55^{\circ}C$ and $63^{\circ}C$, roll surface roughness $Ra(r)=0.5{\mu}m$, $Ra(r)=0.7{\mu}m$ and $Ra(r)=1.0{\mu}m$. The glossiness was declined rapidly when the micro defects ratio was above 23%. With the pass number increasing, the micro pit defects were reduced, uneven peak was decreased and gently along rolling direction. The micro pit defects were increased with the roll surface roughness increase. The defects ratio was declined with larger gradient at pass number 1 to 3, but gentle slope at pass number 4 to 5. When work roll diameter was small, bite angle was increasing, lubrication oil in micro pit of deformation zone was decreased, micro defects were decreased, and glossiness value on the surface of strip was increased.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.1121-1129
• /
• 1988

An economic and efficient system for measuring drop sizes was developed. Pattern recognition technique was used with conventional oil-bath sampling and photographic method. The system was designed to measure and count relatively large number of drops in a very short time, and also to filter out abnormal images such as drops in contact or overlap as well as odd-shaped foreign materials. In this measuring system, most important error originates from the process of converting the original image to the binary image. If the photograph contains a large number of spray drops, the relative size of the pixel to the drops is not infinitesimally small; thus the proper choice of threshold level to convert the original image to the binary image becomes very important. In present case, most of the images lay in one of the two separate bands of brightness level and the arithmetic mean of the most popular brightness levels from each band was chosen as the threshold level. Present image processing system reduces the subjective error by the observers in counting and measuring drops and turns out to be substantially effective. The processing time can be further reduced by improving the hardware system concerned with the digital image coding.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.528-534
• /
• 2020

The early development and use of plate heat exchangers (PHE) were in response to stringent statutory requirements from dairy products in the late 19th century, but PHEs were not exploited commercially until the 1920s. Since then, although the basic concept of PHEs has changed little, its design and construction have progressed significantly to accommodate higher temperatures and pressures, as well as large heat exchanging capacities. The development of current chevron-type corrugated heat plates has been ongoing since the oil shock in the 1970s to improve energy efficiency. The development trend of PHEs is consistent with the development of larger heat plates with better thermal efficiency, lower pressure drop, and good flow distribution. In this study, the thermal performance of small heat plates (PHE-S) and large heat plates (PHE-L) with the same plate depth and corrugation pitch were analyzed experimentally for each channel (H, M, and L type) to suggest development directions of heat plates. The test results showed that for the convectional heat transfer coefficient, the PHE-S was on average, 16.5% higher in the H type, 25% higher in the M type, and 40% higher in the L type than PHE-L. In the case of the pressure drop, the PHE-S was 19% higher in the H type, 46% higher in the M type, and 61% higher in the L type than PHE-L. These results were attributed to the differences in fluid distribution areas between the PHE-S and PHE-L, among other potential causes.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.8 no.1
• /
• pp.1-15
• /
• 2004

Due to recent scientific innovations in mulberry cultivation, leaf yield has been increased manifold. However, with successive leaf harvest, a quantum drop in leaf yield and quality has been noted. This inturn has affected the silkworm rearing and farmers suffered by the frequent crop failures. This is mainly due to nutrient deficiencies in mulberry leaf. Moreover, no complete information is available about hunger signs of nutritional disorders, analytical diagnosis and critical levels of nutrients required. The present paper, thus, may serve as an important nutrient guide for identification of hunger signs, leaf nutrients status under deficiency and critical levels of the elements namely N, P, K, Ca, Mg, S, B, Cu, Fe, Mn and Zn requirements for higher leaf yield and quality. The leaf nutrient status provided may help chemist for correcting the soil status. Besides, an integration of mulberry intercropping with legumes and applications of neem and castor oil cakes, VA-mycorrhizal inoculation, biofertilizer and vermicompost are suggested as integrated nutrient management for sustainable sericulture industry. Based on the information described in this paper, a model needs to be framed for maintaining continuous supply of nutrients to obtain desired quantity and quality of mulberry leaf for successful silkworm cocoon crop and increasing overall silk productivity.