• Journal of Mechanical Science and Technology
• /
• 제18권9호
• /
• pp.1661-1667
• /
• 2004

An experimental study is performed on atomization characteristics and stable operating conditions for the injection of high viscous waste vegetable oil using an effervescent atomizer with 2 aerator tubes. Consideration is given to the effects of ALR and liquid viscosity on the velocity and mean diameter of the injected droplet. It is found that (i) as ALR increases, the axial velocity of the droplet is increased, while half-velocity width and SMD are decreased regardless of the change in liquid viscosities, (ii) the rate of fine drop distribution occupied in the total spray field is increased with an increase in ALR, and (iii) the effect of viscosity on the atomization characteristics is minor. Consequently, it is expected that the effervescent atomizer will exhibit an excellent atomization performance at the high ALR condition, regardless of liquid viscosities.

• 한국수소및신에너지학회논문집
• /
• 제19권3호
• /
• pp.226-231
• /
• 2008

Cu/Fe/$Al_2O_3$ granules with various sizes have been prepared by a combination of sol-gel and oil drop method for the use in sulfur trioxide decomposition, a subcycle in thermochemical sulfur-iodine cycle to split water in the hydrogen and oxygen. The size of composite granules have been mainly changed by the flow-rate of the gel mixture before dropping in the synthesis. The structural properties of the samples were comparable with granule size. In the reaction, the catalytic activity was enhanced by decreasing size in the entire reaction temperature ranges.

• 한국수소및신에너지학회논문집
• /
• 제19권6호
• /
• pp.545-551
• /
• 2008

Fe/$Al_2O_3$ composite granules were prepared by combining sol-gel/oil drop method. The shape of granules were mainly determined by composition and concentration of aluminum precursor. The composite granule with the lowest aluminum concentration was synthesized with 0.75M boehmite solution. The prepared granules were tested as a catalyst in the plug-flow reactor for Fischer-Tropsch synthesis. Before the reaction, catalysts were activated by hydrogen reduction and synthesis gas treatment. The activation conditions and aluminum concentration have affected catalytic performance significantly.

• 한국가정과교육학회지
• /
• 제7권1호
• /
• pp.1-10
• /
• 1995

This study was intended to provide an improved method for testing textiles in high school. Four kinds of test subjects were selected and applied to the classes. Problems of the methods in the textbooks were corrected as follows: 1)Burning test: The number of specimen is reduced to 3 kinds of fibers(cotton, wool, and polyester) and recommends are given to make result by comparing with the burning characteris-tics of paper and hair. 2) Absorbency test: Test Method is changed to drop test. The result is recorded by measuring time required for the water drops absorbed to the specimen. 3) Wrinkle recovery test: A glass is provided instead of metal weight. The method of measuring angle which is made by the specimen is shown in figure. 4) Effects of Detergent: 0.2% of detergent solution is provided before class. The amount of oil and carbon black is specified. Students have generally agreed that the improved methods were better than those in the text-books after they made the above 4 recommendable experiments(p<.001)

• Ocean Systems Engineering
• /
• 제10권3호
• /
• pp.267-287
• /
• 2020

The dropped objects are identified as one of the top ten causes of fatalities and serious injuries in the oil and gas industry. It is of importance to understand dynamics of dropped objects under water to accurately predict the motion of dropped objects and protect the underwater structures and facilities from being damaged. In this paper, we study non-dimensionalization of two-dimensional (2D) theory for dropped cylindrical objects. Non-dimensionalization helps to reduce the number of free parameters, identify the relative size of effects of force and moments, and gain a deeper insight of the essential nature of dynamics of dropped cylindrical objects under water. The resulting simulations of dimensionless trajectory confirms that drop angle, trailing edge and drag coefficient have the significant effects on dynamics of trajectories and landing location of dropped cylindrical objects under water.

• 한국기계연구소 소보
• /
• 통권18호
• /
• pp.29-35
• /
• 1988

When low sliding velocities in the boundary lubrication range are operating, irregular movements frequently occur which are a result of the stick-slip phenomenon. Such slide motions are undesirable in precision machine tools, particularly with feed back systems used in numerical and adaptive control machine tools. Accordingly, this paper reports analytical and experimental studies in the stick-slip characteristic of machine tool feeding system. The main conclusions of this study are as follows; The tendency towards stick-slip effects may be reduced by; 1). Reducing the drop in friction coefficient in the Stribeck curve(on the rising part of the friction characteristic at higher sliding speeds, the system is stable all the time) 2). Reducing the transition velocity by the use of a higher viscosity lubricating oil. 3). Increasing the stiffness(Damping)and reducing normal load(Sliding mass) Therefore, the Critical velocity is decided from the above conclusions and in designing of machine tool, feed rates(sliding velocity)must be design the more than critical velocity.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권5호
• /
• pp.589-595
• /
• 2002

Fluid mixing is ubiquitous and essential in many natural and industrial systems. Understanding the mixing processes that occur in these diverse systems is essential for predicting many aspects of practical importance. The objective of this study was to develop a new mixing element and to perform the experimental investigation of flow and mixing in a static mixer that is equipped the new element and the others. Glycerin and gear oil were used as mixing fluids. Pressure drops across the static mixer elements of different designs and different numbers were measured using a hydraulic manometer The axial and cross-sectional views of tracer mixing were photographed using a digital camera. The pressure drops of SSM mixer were about 20% less than that of Sulzer mixer whereas the mixing performance of SSM mixer was not so good as that of Sulzer mixer

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권1호
• /
• pp.79-87
• /
• 1999

The most part of the faculty drop a trouble and damage of machine equipment even if whatever cause they break out take place at local and trifling place and the factor dominating their trouble is due to wear debris occurred in the lubricated machine moving surface. This study has been car-ried out to identify morphology of wear debris on the lubricated machine moving system by means of computer image analysis. Namely the wear debris contained in lubricating oil extracted from movable machine equipment will be filtered through membrane filter(void diameter 0.45${\mu}m$) and will be analyzed with its data information such as 50% volume diameter aspect roundness and reflectivity. Morphological characteristic of wear debris is easily distinguished by four shape parameters it is necessary to divide small class of every 100 wear debris in total wear particles in order to distinguish morphological characteristic of wear debris more easily by computer image analysis. We are sure that operation condition diagnosis of the lubricated machine moving surfaces is possible by computer image analysis.

• 유공압시스템학회논문집
• /
• 제5권1호
• /
• pp.20-26
• /
• 2008

Various types of hydraulic shock absorbers are widely used in many fields because of its numerous advantages. However, in order to design adequate damping characteristics, accurate flow data near the orifices are required essentially. In this paper, a commercial computational fluid dynamics(CFD) code, FLUENT is adopted to investigate the flow characteristics near orifices of a shock absorber. Static pressure and velocity vector distributions, fluid path lines are presented for compression/tension strokes and various piston speeds. In order to validate the result of analysis, the numerically obtained damping forces are compared with those of analytical estimations obtained by modified Bernoulli equation. The results reported herein will provide better understanding of the detailed flow fields within shock absorber, and the CFD analysis method proposed in this paper can be used in the design of other types of hydraulic shock absorber.

• 한국자동차공학회논문집
• /
• 제4권3호
• /
• pp.176-186
• /
• 1996

The phenomena of drag reduction using small quantities of a liner macromolecules has attracted the attention of many experimental investigations. On the other hand drag reduction in two phase flow can be applied to the transport of crude oil, phase change system such as chemical reactor, pool and boiling flow, and to flow with cavitation which occurs pump impellers. But the research on dragreduction in two phase flow is not sufficient. The purpose of the present work is to evaluate the drag reduction by measuring pressure drop, void fraction, mean liquid velocity and turbulent intensity whether polymer additives a horizontal single and two phase system or not. Flow pattern of air-water two phase flow was classified by electrical conductivity probe signal. Velocities and turbulent intensities of signal were measured simultaneously with a Hot-film anemometer.