• Journal of Advanced Marine Engineering and Technology
• /
• 제21권2호
• /
• pp.126-135
• /
• 1997

Drag reduction in polymer solutions is the phenomenon where by extremely dilute solutions of high molecular weight polymers exhibit frictional resistance to flow much lower than the pure solvent. This effect, largely unexplained as yet, has attracted the attention of polymer scientists and fluid flow specialists. Although applications are beginning to appear, the principle interest to data has been in attempting to relate the effect to the fluid mechanics of turbulent flow. Drag reduction in two phase flow can be applied to the transport of crude oil, phase change system such as chemical reactor, and pool and boiling flow. But the research on drag reduction in two phase flow is not intensively investigated. Therefore, experimental investigations have been carried out to analyze the drag reduction produced by polymer addition in the single phase and two phase flow system. The objectives of the proposed investigation are primarily in identifying and developing high performance polymer additives for fluid transportations with the benefits of turbulent drag. Also we want to is to evaluate the drag reduction in horizontal flow by measuring pressure drop and mean velocity. Experimental results show higher drag reduction using co - polymer(A611P) then using polyacrylamide (PAAM) and faster degradation using PAAM than using A611P under the same superficial velocity.

• 대한기계학회논문집B
• /
• 제28권3호
• /
• pp.289-295
• /
• 2004

The heat transfer coefficient and pressure drop during gas cooling process of carbon dioxide in a horizontal tube were investigated. The experiments were conducted without oil in the refrigerant loop. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flowmeter, an evaporator, and a gas cooler(test section). The main components of the water loop consist of a variable-speed pump, an isothermal tank, and a flowmeter. The gas cooler is a counterflow heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus. The test section consists of smooth, horizontal stainless steel tube of the outer diameter of 9.53mm and of the inner diameter of 7.75mm. The length of the test section is 6m. The refrigerant mass fluxes were 200∼300kg/(m2$.$s) and the inlet pressure of the gas cooler varied from 7.5㎫ to 8.5㎫. The main results were summarized as follows : Pressure drop of CO2 increases with increasing gas cooler pressure. The friction factors of CO2 in a horizontal tube show a relatively good agreement with the correlation by Blasius. The heat transfer coefficient of CO2 in transcritical region increases with decreasing gas cooler pressure and decreasing mass flux of CO2. Most of correlations proposed in a transcritical region showed significant deviations with experimental data except for those predicted by Gnielinski.

• Reproductive and Developmental Biology
• /
• 제29권3호
• /
• pp.145-147
• /
• 2005

Autocrine or paracrine mediators released by the early embryo are implicated in the support of embryonic development. Their mechanisms and optimal embryo density in the medium, however, are uncertain. This study was conducted to establish the optimal embryo density and culture medium volume in mouse parthenogenetic embryo culture. In experiment 1, culture of parthenogenetirally activated oocytes at a concentration of $2{\~}4$ embryos/${\mu}L$ significantly improved development to the blastoryst stage ($72{\%}{\leq}$) compared with culture at the lower ($0.2{\~}1$e mbryos/${\mu}L,\;0\~37.5\%$) and the higher ($5{\~}6$ embryos/${\mu}L,\;30\~53\%$) concentration for 120 h when the oocytes were cultured in a 5 ${\mu}L$ drop under mineral oil In experiment 2, the embryos cultured at a concentration of $2{\~}4$ embryos/${\mu}L$ in a 10 ${\mu}L$ drop ($81.1{\%}$) showed significantly higher blastocyst rates than those in a 5 ${\mu}L$ drop ($68.5{\%}$). This study optimizes in vitro culture condition by modifying embryo density and the volume of culture medium It may give appropriate level of autocrine and/or paracrine factors to enhance viability and subsequent normal development of mouse parthenogenetic embryos in vitro.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제12권3호
• /
• pp.158-167
• /
• 2004

Condensation heat transfer experiments were conducted with a oblong shell and plate heat exchanger without oil in a refrigerant loop using R-134a. An experimental refrigerant loop has been developed to measure the condensation heat transfer coefficient $h_r$ and frictional pressure drop ${\Delta}p_f$ of R-134a in a vertical oblong shell and plate heat exchanger. Four vertical counter flow channels were formed in the oblong shell and plate heat exchanger by four plates having a corrugated sinusoid shape of a $45^{\circ}$ chevron angle. The effects of the refrigerant mass flux, average heat flux, refrigerant saturation temperature and vapor quality were explored in detail. Similar to the case of a plate heat exchanger, even at a very low Reynolds number, the flow in the oblong shell and plate heat exchanger remains turbulent. The results indicate that the condensation heat transfer coefficients and pressure drops increase with the vapor quality. A rise in the refrigerant mass flux causes an increase in the $h_r\;and\;{\Delta}p_f$. Also, a rise in the average heat flux causes an increase in the $h_r$. But the effect of the average heat flux does not show significant effect on the ${\Delta}p_f$. On the other hand, at a higher saturation temperature, both the $h_r\;and\;{\Delta}p_f$. found to be lower. Based on the present data, the empirical correlations are provided in terms of the Nusselt number and friction factor.

• 한국의학물리학회지:의학물리
• /
• 제9권2호
• /
• pp.89-94
• /
• 1998

자기공명영상을 정위적 방사선 수술에 이용하기 위한 우선 과제로 비교적 균일한 phantom에서 자기공명영상으로 구한 정위적 표적점이 실제 방사선수술시의 방사선 빔의 isocenter와 일치하는지 확인하고자 하였다. 무 속에 임의의 표적점이 표시된 선량측정용 필름을 끼우고 head ring 을 고정시킨 다음 자기공명영상올 얻어 방사선 수술용 planning computer 로 표적점의 정위적 좌표를 구한 다음 실제 치료와 같이 무 phantom 을 테이블에 고정한 후 구해진 표적점의 좌표를 isocenter로 하여 방사선을 조사하고 필름을 현상하여 필름에 표시한 표적점과 실제 방사선이 조사된 부위의 선량분포의 중심을 비교하였는데 오차가 0.5 mm 이내였다. 따라서 무와 같은 비교적 균일한 phantom 에서는 표적점과 실제 방사선이 조사된 부위의 선량분포의 중심이 잘 일치함을 알 수 있었다. 또 다른 방법으로 자기공명영상의 왜곡의 정도를 직접 확인하기 위해서 아크릴에 1 cm 간격으로 구멍을 뚫고 오일방울을 넣어준 후 아크릴 phantom을 무 속에 수평과 수직방향으로 삽입한 뒤 자기공명영상을 얻은 후 각각의 좌표를 구하여 자기공명영상의 수평과 수직방향에서 왜곡의 정도를 측정하였다. 결과는 균일한 물질 내에서는 7 cm 거리에서 0.4 mm 이내의 오차를 보여서 비교적 잘 일치하였다. 그런데 이 측정과정에서 device 자체와 digitizing 과정의 오차가 있는 것으로 판단되므로 더 정교한 device 의 제작이 필요한 것으로 생각된다.

• Korean Chemical Engineering Research
• /
• 제50권6호
• /
• pp.969-979
• /
• 2012

본 연구에서는 보조계면활성제 첨가가 nonylphenol ethoxylate (NP) 계면활성제, 물, 탄화수소 오일의 3성분으로 이루어진 시스템의 평형 및 동적 거동에 미치는 영향을 살펴보았다. 실험에서 사용한 펜탄올, 옥탄올, 데칸올 등의 보조계면활성제는 모두 소수성 첨가제로 작용하였으며, 소수성 증가 효과는 알코올의 사슬 길이 증가 및 첨가량 증가에 따라 증가하였다. 계면활성제 시스템이 친수적인 조건에서는 비극성 오일의 종류에 상관없이 시간에 따라 오일의 크기가 감소하였으며, 마이셀 용액에 의한 탄화수소 오일의 가용화는 diffusion-controlled 메커니즘이 아닌, interface-controlled 메커니즘을 따름을 확인할 수 있었다. 반면에 소수성 조건에서는 과포화로 인하여 일어나는 자발적 유화 현상과 물과 계면활성제의 오일상으로의 확산으로 인한 오일의 크기 증가가 관찰되었다. 비극성 탄화수소 오일과 계면활성제 수용액 사이의 시간에 따른 계면장력 측정 결과는 동적 거동 실험결과와 일치하는 경향을 나타내었다. 한편 middle-phase 마이크로에멀젼을 포함한 3상이 형성되는 조건에서는 매우 낮은 계면장력으로 인하여 오일이 수용액 상에 빠른 속도로 가용화되었고 작은 방울 형태로 유화되었다.

• 국제지역연구
• /
• 제20권1호
• /
• pp.23-51
• /
• 2016

한-GCC FTA 체결은 안정적인 에너지 자원의 확보에서 뿐만 아니라 향후 대규모 소비시장으로서 GCC의 성장 잠재성과 한국과의 보완적인 산업 구조를 고려해 볼 때 그 중요성이 크다. 최근 한-GCC FTA의 필요성이 제기되고 있는 시점에서 한-GCC FTA의 경제적 기대 효과에 대하여 분석하고 FTA의 조속한 체결의 필요성을 제시하고자 하였다. 한-GCC FTA의 경제적 효과를 알아보기 위하여, 본 연구에서는 원유관세 인하를 통한 경제적 효과를 분석하기 위하여 벡터자기회귀모형(VAR: Vector Autoregression Model)을 이용하였다. 추정 결과, GDP는 총 0.212%, GNI는 0.389%, 소비는 0.238% 증가한다. 반면 투자, 수출, 수입은 각각 0.462%, 0.413%, 0.342% 감소하는 것으로 나타났다. 물가수준의 경우 생산자물가상승률은 6.356%p, 소비자물가상승률은 2.996%p 감소하는 것으로 나타났다. 즉, GCC와의 FTA를 통한 원유수입관세의 철폐 및 이로 인한 원유수입가격의 하락은 물가의 하락을 가져오는 동시에 GDP, GNI, 소비 등의 거시경제지표의 증가를 통해 우리나라 경제성장에 긍정적인 영향을 미침을 알 수 있다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.436-439
• /
• 2008

This paper is to research the heat transfer performance of the sintered pipe. Recently, oil prices is to be 127 $ per barrel, we expect higher costs this summer. We promote alternative fuels, after oil and gasoline prices reached record highs. The governments have made efforts to avoid future crisis by continuing the move toward renewable energy and energy saving. In this paper, we have fabricated a sintered pipe, the heat transfer performance of sintered pipe is achieved experimentally. The pipe is copper tube of outer diameter of 15.88 mm, the length of the pipe is 800 mm. Based on the experimental results, it is shown the overall heat transfer coefficient of sintered pipe is increased as compared with that of a straight pipe, is equal as compared with that of a spiral pipe. The overall heat transfer coefficient was $0.075{\sim}0.09\;kW/^{\circ}C$

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.531-536
• /
• 2004

In-arm type hydropeumatic suspension unit(ISU) is an equipment of armed tracked vehicle to absorb impact load and vibration from the irregular ground. During the operation of ISU, main piston moves forward and backward and oil flowing through damper transmits the external impact load to floating piston. Heat is generated in ISU by the oil pressure drop through the damper orifice and the friction between cylinder wall and two pistons. On the other hand, internal heat dissipatis outside via heat convection. Occurrence of high temperature can deteriorate durability of major components and basic function of ISU. And, it can cause fatal problem in the ISU life time and the sealing performance of piston rings. As well, the spring constant change of nitrogen gas that is caused by the temperature rise exerts the negative effect to the vehicle stability. Therefore, in this paper, we analyze the heat transfer analysis of the entire ISU unit, by finite element method, with the outside flow velocities 8m/s and 10m/s.

• 드라이브 ㆍ 컨트롤
• /
• 제18권3호
• /
• pp.1-7
• /
• 2021

In a hydraulic control system, since a hydraulic cylinder drives a relatively large mass of an object, an external load force acts as a disturbance on the control performance of the system. Additionally, as the hydraulic system is used for a long period, there are disturbances that occur gradually, such as a drop in supply pressure because of abrasion of the pump, oil leakage from a valve, and oil leakage from a cylinder. In this study, a state feedback controller based on a linearization technique is applied. To prevent the performance degradation of the controller from the load disturbance, an Extended Luenberger observer (ELO) is used for the Extended system. The case of using the proportional controller, which is a representative linear controller, and the result of using the controller designed in this study are compared and reviewed through simulation. Also, we propose an experimental gain-setting method for a state feedback controller that can be used at industrial sites, and examine how the stability and control performance of the system changes because of the disturbance inputs through the experimental results.