• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1991.04a
• /
• pp.154-160
• /
• 1991

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.151.2-151.2
• /
• 2000

• Journal of information and communication convergence engineering
• /
• v.4 no.4
• /
• pp.162-165
• /
• 2006

This paper presents a bandwidth efficient self-cancellation scheme for interchannel interference (ICI) in OFDM transmission systems. Conventional self-cancellation schemes provide an excellent cancellation capability of ICI for relatively low frequency offsets. However, this capability is achieved at the expense of bandwidth efficiency and thus a higher modulation level is often used to compensate for desired throughput. By applying a partial differential coding (PDC) to the transmit data prior to the ICI self-cancellation, bandwidth efficiency is greatly improved by a factor of 2, while maintaining a string of data (+1, -1) alternately for the ICI. self-cancellation in OFDM systems. Computer simulations show that the performance of the proposed scheme is comparable to the conventional self-cancellation scheme with slight performance degradation for relatively lower frequency offsets.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.427-428
• /
• 2002

Clearance movements of engine piston are regarded very important because they cause impact vibrations as well as many tribological problems. Some of the major parameters that influence these kinds of performances are piston profiles, piston offsets and clearance magnitudes. In our study. computational investigation is performed about the piston movements in the clearance between piston and cylinder liner by changing the skirt profiles and piston offsets. Our results show that curved profile and more offset to thrust side have better performance with low side impact during the engine cycle.

• Korean Journal of Computational Design and Engineering
• /
• v.15 no.4
• /
• pp.253-260
• /
• 2010

This paper presents algorithms for computing offsets of freeform curves. The approach first divides the original curve into several segments at the inflexion points. Based on the obtained new control polygon and its offsets, quadratic trigonometric splines are constructed to approximate the offset curves. Finally, the shape parameter value of trigonometric spline is determined to satisfy the required tolerance. The degree of the output curve is two, independent of the original curve's degree. Because of the great controllability, the proposed method can generate a completely overestimating offset curve by adjusting the value of the shape parameter, which guarantees no overcutting in NC machining. Furthermore, it also produces the lowest number of control points compared with other works.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.162-169
• /
• 2000

A Direct Drive Valve(DDV) hydraulic actuation system which is commonly used as an aircraft's control surface driving actuator has multi-loop control structure to ensure its safety operation. However, because of not perfect matching of one self channel characteristics with the others, the servo valve driving current of each channel can be widely different. Therefore, the long-time use of DDV actuator without any correction of these channel current offsets will cause the problem of performance or life expectancy degradation due to unwanted heats in the linear motor. A current equalization loop structure which can minimizes current offsets between channels is introduced and designed. The performance of the current equalization loop is investigated and verified through the analytic and experimental ways.

• Journal of Korean Society of Transportation
• /
• v.6 no.2
• /
• pp.49-56
• /
• 1988

Alternate use of lane at a signalized intersection is a quite different control of the operation of an intersection. This control introduces a new stop line and signal before the original stop line. All of the lanes between the two stop lines are used for left turn traffic or through traffic at a time. The purpose of the control is increasing the capacity of a n intersection without widening the approach width. this paper contains a study on the condition of a application, the proper distances between the two stop lines, the reasonable offsets(rear) to guarantee clearing the vehicles of previous phase, the comparison of approach capacity between the existing control and this control. The study results reveals that the offsets(rear) are rather stable showing the range(maximum value minus minimum value) of it's value does not exceed 3.6 seconds according to the field data. The approach capacity will be increased by 27%, 43%, 59%, 84% when the distances between the stop lines are 30.0m respectively. The control might have theoretical limitation to operate in practice. So an experimental application of the control at some suitable intersections prior to expanding it.

• Journal of the Korean Professional Engineers Association
• /
• v.27 no.3
• /
• pp.121-131
• /
• 1994

It is very difficult to partially describe the hull shape made up of 3-dimensional free form surface. With computerizing skill in ship design, the geometric modeling technique has been developed. In hull shape modeling, the blending technique has not yet been adapted to the hull shape surface has a variable curvature. By adapting the blend surface, small surface on drawing plane is to be softly blended with given hull surface and a projecting part. This study has adapted to the ship design one of the blending methods by which offsets data of the blend surface can be obtained by the input of blend radius on two base surfaces.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2001.10a
• /
• pp.325-328
• /
• 2001

This paper introduces a new technique to extract eigenvalues of the gain and phase offsets and to compensate them automatically in transducerless sampling RTU. It discusses in detail the cause of the offsets, describes the principles of gain and phase compensation, establishes the algorithm to extract eigenvalues. The process of using the compensated measurements is also illustrated in the paper. This technique enhances the operational speed, simplifies the operational complexity, and improves the capability of transducerless sampling in RTU.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2007.09a
• /
• pp.440-449
• /
• 2007

Recently, researches for side resistances of drilled shafts considering socket roughness have been conducted actively. In order for these researches, roughness measurement devices using laser sensor were developed by two research groups. The devices were only applied in boreholes with dry conditions. In this research, a roughness measurement devices using the laser sensor (BKS-LRPS) was developed, which could apply in wet conditions and also measure vertical offsets of drilled shafts. In addition, the application of the laser sensor to the geotechnical engineering proposed in this paper.