• The Journal of the Acoustical Society of Korea
• /
• 제16권2E호
• /
• pp.47-54
• /
• 1997

This paper presents two results on intersymbol interferences in baseband digital communication over an additive white Gaussian noise channel-the interferences due to mismatched square-root raised-cosine filters, in which the filters have different roll-off factors, and / or due to sampling-time jitter. The result for the mismatched filters is that even the jitter-free sampling causes intersymbol interference and it is negligibly small for a wide range of signal-to-noise ratio up to 10dB, for the roll-off factor ranging from 0.2 to 0.5, the mismatch loss being within 0.1dB from the optimum at around 10-6 .For jitter interference an approximation formula for the bit error probability is derived in case of the matched filters, which shows how the roll-off factors and the amount of jitter affect the system performance. The formula is reasonably accurate.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2006년도 Proceedings of ISRS 2006 PORSEC Volume I
• /
• pp.263-266
• /
• 2006

Now, on the developing COMS(Communication, Ocean and Meteorological Satellite) has solar panel on the South panel only. Therefore, the wheel off-loading has to be performed periodically to reduce a induced momentum energy by a asymmetric solar panel. One of two East/West station keeping maneuver to correct simultaneously longitude and eccentricity, orbit corrections may be performed during one of the two wheel off-loading manoeuvres per day to get enough observation time for meteorological and ocean sensor. In this paper, we applied a linearized orbit maneuver equation to acquire maneuver time and delta-V. Nonlinear simulation for the station keeping is performed and compared with general station keeping strategy for fuel reduction.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.692-697
• /
• 1997

This paper presents a method of grinding and polishing automation of precision die after CNC machining. The method employs a robot system equipped with a pneumatic spindle and a special abrasive film pad. The robote program is automatically generated off-line from a PC and downloaded to robot controller. Position and orientation data for the program is supplied from cutter contact (CC) data of NC machining process. This eliminates separate robot teaching process. This paper aims at practical automation of die finishing process which is very time consuming and suffering from shortage of workpeople. Time loss for changeover from one product to next is eliminated by off-line programming exploiting appropriate NC machining data. Dextrous 6-axis robot with rigid wrist and simple tooling enables the process applicable to larger, rather complex 3 dimensional free surfaces

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.61-66
• /
• 2010

Pay off reel is the device to release in the form of coil. Every time the device becomes a hassle to exchange, each diameter of two forms has been applied to the coil reel. There is the change of reel diameter of the sleeve portion to be the part of segment geometry. This unit is conducting on 3-dimensional modeling design. The basic strength and deformation of the device could be checked in advance by the basis of 3-d modeling data to perform simulations. The production of each part can be completed and assembled. Conducted for the final product which is tested and measured, all items are satisfied within the limits of targets. Due to the development of this device, the efficiency on operations can be increased and the production time becomes shortened.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.84-87
• /
• 1996

This paper presents a energy function to reflect the control effect of speed governor which has a cut-off property which means position and rate limit The proposed energy function satisfies the semi-negativeness of its time derivative and well reflects the parameters of speed governor to the energy function. The transient stability analysis by the direct method for the single machine infinite bus system has been conducted with the use of the proposed energy function, which shows that the results by the direct method well agree with that by the conventional time simulation method. This thesis shows a possibility of more accurate stability analysis by taking into account the cut-off property of speed governor's output.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.22-23
• /
• 2006

Proton irradiation technology was used for improvement of switching characteristics of the PT-IGBT. Proton irradiation was carried out at 5.56 MeV energy with $1{\times}10^{12}/cm^2$ doze from the back side of the wafer. Characterization of the device was performed by I-V, breakdown voltage, threshold voltage, and turn-off delay time measurement. For irradiated device by 5.56 MeV energy, the breakdown voltage and the threshold voltage were 730 V and 6.5~6.6 V, respectively. The turn-off time has been reduced to 170 ns, which was original $6\;{\mu}s$ for the un-irradiated device.

• 한국정밀공학회지
• /
• 제16권3호통권96호
• /
• pp.9-17
• /
• 1999

This paper presents a method of grinding and polishing automation of precision die after CNC machining. The method employs a robot system equipped with a pneumatic spindle and a special abrasive film pad. The robot program is automatically generated off-line program form a PC and downloaded to robot controller. Position and orientation data for the program is supplied form cutter contact (CC) data of NC machining process. This eliminates separate robot teaching process. This paper aims at practical automation of die finishing process which is very time consuming and suffering from shortage of workpeople. Time loss due to changeover from one product to another is eliminated by PC off-line programming exploiting appropriate NC machining data. Dextrous 6-axis robot with rigid wrist and simple tooling enables the process applicable to larger, rather complex 3 dimensional free surfaces.

• Tribology and Lubricants
• /
• 제17권6호
• /
• pp.441-446
• /
• 2001

In this paper the effect of bump compliance, load, and the number of pad on the lift-off speed is studied. When the load is greater and bump compliance lower, the shaft is lifted off at higher rotating speed. And when the load is applied near the center of pad, lift-off speed is lower. When the number of pad increases, the lift-off speed is higher. The lift-off characteristics can be used to lengthen the lift time of the coating and design the rotating machinery supported by bump bearings.

• 한국벤처창업학회:학술대회논문집
• /
• 한국벤처창업학회 2022년도 춘계학술대회
• /
• pp.157-161
• /
• 2022

Building on the DC interaction model between a parent company and its spin-offs, we examine that a dyadic relationship can be differentiated within the functions of space, motivation, and time. We investigate that these three factors encompassing the parent-spin-off DC relationship can be applicable to both linear(i.e., geographic proximity and low spin-off CEO's salary is positive) and nonlinear(i.e., too much frequency of new spin-off creation is as harmful as too little) effects on determining the performance of spin-off firms. The direction of causality is underpinned by social capital, human capital, and compensation-activation theory rather than by the normal consequences of previous empirical research. Further, our results suggest the overlap between DC and entrepreneurship; namely, spin-off firms create, learn, and exploit opportunities through a reconfiguration of parent DC so that DC establishes itself as a key concept in the entrepreneurship domain.

• 생명과학회지
• /
• 제18권11호
• /
• pp.1493-1498
• /
• 2008

본 연구는 심폐바이패스를 이용한 성인 심장수술 시 수술 후 환자의 회복 결과에 영향을 미치는 인자들을 규명하기 위해 시행하였다. 성인 심장수술 환자 32명을 대상으로 하여 연구하였다. 심장수술 시 밸혈구 수, GOT, troponin-I (cTNI), interleukin-6 (IL-6), endothelin-1 (ET-1), D-dimer, neuron-specific enolase (NSE) 등의 혈장농도는 유의하게 증가한데 비해 혈소판 수는 감소하였다. 수술 직후 GOT 및 D-dimer 농도와 24 시간 및 총출혈량, 기계호흡보조 시간, 중환자실 치료기간, 재원일수와 각각 양의 상관성이 있었다. 혈소판 수와 기계호흡보조 시간, 중환자실 치료기간, 재원일수와 각각 음의 상관관계가 있었다. Creatinine 농도와 기계호흡보조 시간, 중환자실 치료기간 사이에 양의 상관성이 있었다. NSE 농도와 24 시간 출혈량 사이에 양의 상관관계를 보였다. cTNI 농도와 재원일수 간에 양의 상관성이 있었다. 대동맥 교차차단 및 총심폐바이패스 실시 시간과 24 시간 및 총 출혈량, 재원일수 사이에 양의 상관관계를 나타내었다. 결론적으로 본 연구의 결과들은 심폐바이패스를 적용한 성인 심장수술 시 수술 후 환자의 결과와 회복에 영향을 미치는 가장 중요한 변수는 수술 종료 직후(CPB-off)의 GOT, BUN, creatinine, D-dimer 등의 농도와 혈소판 수임을 시사하고 있다.