• 한국항공우주학회지
• /
• 제37권8호
• /
• pp.805-811
• /
• 2009

가스발생기 사이클의 추력 30톤급 엔진에 적용 가능한 터보펌프의 구성품인 산화제펌프에 대하여 실제 작동 유체인 액체산소를 이용한 시험이 이루어졌다. 본 시험에서 터빈은 상온 수소 가스로 구동되었다. 산화제펌프는 설계점 및 탈설계점에서 안정적으로 작동되었고 성능 요구조건을 만족시켰다. 액체산소를 매질로 하는 경우의 산화제펌프 양정계수는 물을 매질로 하는 경우에 비하여 약 2~3% 더 낮은 값을 보였다. 산화제펌프 구동에 필요한 동력과 터빈에서 생성되는 동력이 서로 잘 일치하였다.

• 한국산학기술학회논문지
• /
• 제14권5호
• /
• pp.2069-2074
• /
• 2013

내연기관 차량에 전자기식 클러치 워터펌프의 적용은 연비 향상 및 배기가스 저감을 꾀할 수 있다. 이러한 클러치 워터펌프는 엔진 냉각시스템의 유량 단속에 의하여 최적 운전 조건을 가능케 한다. 본 연구에서는 클러치 워터펌프를 이용한 냉각시스템을 제어함으로써 디젤 차량의 연비 및 배기가스 특성을 살펴보았다. 전자기식 클러치 워터펌프에 의한 저온 시동시 냉각수 흐름을 차단하여 아이들 조건에서 예열 시간을 기존 워터펌프 대비 49% 정도 단축시켰고, 주행 중에는 냉각수가 최적 고온상태를 유지하도록 제어하였다. 그리하여 NEDC 모드에서 연소 효율이 개선되어 최대 5% 정도의 연비 향상 효과를 나타내었다. 또한 NOx를 제외한 HC, CO 및 $CO_2$ 배기가스의 농도가 전반적으로 감소하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권2호
• /
• pp.256-263
• /
• 2002

The Boil-Off-Gases(BOG) in the LNG production terminal are continuously generated during the unloading, storage and supply processes by the heat penetration. In order to use these gases as useful fuel, the reliquefaction process should be installed to put the reliquefied BOG in the main LNG supply line before the secondary pump in terminal. The current reliquefaction method of BOG in LNG terminal is the direct contact one between LNG and BOG in the absorption column. But the system has severe disadvantage, which is the 10 times of LNG circulation needed for unit mass of BOG reliquefaction. It causes, therefore, high power consumption of LNG circulation pump and excessive city-gas supply, even if short demand of NG is needed in the summer time. In this paper, the new reliquefaction system of BOG by using LNG cold energy with indirect contact in precooler was suggested and analysed. The result showed new indirect contact method of BOG reliquefaction system between LNG cold energy and BOG is much more effective than the current direct contact one because of only about 1.3 times of LNG circulation needed and higher energy saving by pump power reduction.

• 한국산학기술학회논문지
• /
• 제19권9호
• /
• pp.146-155
• /
• 2018

본 연구는 허혈성심장질환으로 관상동맥우회술을 받은 환자에서 심폐바이패스 여부에 따른 임상성과를 확인하고자 시행하였다. 연구대상은 2008년 7월부터 2012년 6월까지 4년 동안 허혈성심장질환으로 관상동맥우회술을 받은 환자 전수이며, 총 10,981명이었다. 분석 자료는 건강보험심사평가원 청구명세서를 이용하여 후향적으로 수집하였다. 연구결과, 무심폐기 관상동맥우회술(Off Pump CABG, OPCAB) 환자 그룹이 고식적 관상동맥우회술(On Pump CABG, ONCAB) 환자 그룹에서보다 평균 수술소요시간(280분 vs 357분, p<.0001) 및 기관 내 삽관 후 발관까지 평균 소요시간이 짧았고(약 24시간 vs 40시간, p<.0001), 수술 후 출혈 및 혈종 등으로 인한 재수술률이 낮았다(2.7% vs 8.3%, p<.0001). 위험요인 통제 하에 심폐기 사용 여부에 따른 30일내 사망률과 재원일수를 분석한 결과, 고식적 관상동맥우회술(ONCAB) 대비 무심폐기 관상동맥우회술(OPCAB)의 사망 위험비는 0.339(0.266-0.434)이고, 재원일수는 -0.29229로 감소하였다(p<.0001). 이상의 결과 심폐기를 사용하지 않은 경우에서 30일내 사망률과 재수술률이 낮았고, 평균 수술소요시간, 기관 내 삽관 후 발관까지 소요시간, 재원일수가 짧았음을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.382-384
• /
• 1996

This paper introduces the controller development of booster multi-pump system with constantly estimated control algorithm. Through analyzing by the experiment of optimal pressure with a certain flow rate. The larger pressure processing apparatus in microprocessor makes optimal water-supplying. This method is implemented with the only pure control algorithm without any other mechanical or circuitry apparatus. Also, Pump's life is lengthened by exchanging simple on, off and rotational inverter control. Optimal condition for pump is adjusted by the inverter control, and compact control panel helps the booster system install in real field.

• 설비공학논문집
• /
• 제13권3호
• /
• pp.200-208
• /
• 2001

In indoor temperature control of a heat pump, a reduction in energy consumption is very important. However, most control schemes for heat pumps have focused only on control performance such s settling time and steady-state error. In this paper, the model predictive control (MPC) which includes the energy-related variable in this cost function is proposed. By computing the control signal minimizing this cost function, the trade-off between energy reduction and temperature control performance can be obtained. Since the MPC required the process model, the dynamic mode of a heat pump is also obtained by the system identification technique. Performance of the proposed MPC considering energy efficiency is compared with the two other control schemes. It si shown that the proposed scheme can consume less energy thant hte others in achieving similar control performance.

• 한국유체기계학회 논문집
• /
• 제5권1호
• /
• pp.33-41
• /
• 2002

Low NPSH and high pressure pumps we widely used for turbopump systems, which have an inducer and operate at high rotating speeds. In this paper, a meanline method has been established for the preliminary design and performance prediction of pumps having an inducer for cavitating or non-cavitating conditions at design or off-design points. The method was applied for the performance prediction of a fuel pump. Predicted performances by the method are shown to be in good agreement with experimental results for cavitating and non-cavitating conditions. The established meanline method can be used for the performance prediction and preliminary design of high speed pumps which have a inducer, impeller and volute.

• 대한기계학회논문집A
• /
• 제33권11호
• /
• pp.1239-1243
• /
• 2009

To evaluate the structural integrity of the nuclear seismic category penetration cooling water pump under the seismic service conditions the seismic analysis was performed in accordance with IEEE-STD-344 code. The finite element computer program, ANSYS, Version 10.0, is used to perform both a mode frequency analysis and an equivalent static seismic analysis of the pump assembly. The mode frequency analysis results show the fundamental natural frequency is greater than 33 Hz and does not exist in seismic range, thus justifying the use of the static analysis. The stresses resulted from various loadings and their combinations are within the allowable limits specified in the above mentioned IEEE code. The results of the seismic evaluation fully satisfied the structural acceptance criteria of the IEEE code. Accordingly the structural integrity on the pump assembly was proved.

• International Journal of Fluid Machinery and Systems
• /
• 제4권1호
• /
• pp.172-178
• /
• 2011

This paper presents an optimization procedure for high-efficiency design of a mixed-flow pump. Optimization techniques based on a weighted-average surrogate model are used to optimize a vane diffuser of a mixed-flow pump. Validation of the numerical results is performed through experimental data for head, power and efficiency. Three-level full factorial design is used to generate nine design points within the design space. Three-dimensional Reynoldsaveraged Navier-Stokes equations with the shear stress transport turbulence model are discretized by using finite volume approximation and solved on hexahedral grids to evaluate the efficiency as the objective function. In order to reduce pressure loss in the vane diffuser, two variables defining the straight vane length ratio and the diffusion area ratio are selected as design variables in the present optimization. As the results of the design optimization, the efficiency at the design flow coefficient is improved by 7.05% and the off-design efficiencies are also improved in comparison with the reference design.

• 한국생산제조학회지
• /
• 제9권5호
• /
• pp.87-95
• /
• 2000

The numerical analysis and the experiments are carried out to develop the design program for the flow control valve attached to the vane pump for power steering. The factors affecting the flow rate characteristics are analyzed by the experiments and the numerical analysis. The results are summarized as follows; (1) the main factors affecting to the first and second control flow rate are the diameter of big and small rod of the spool. (2) the cut off is mainly affected by the main spring constant, the initial displacement of main spring and the small diameter of the spool. (3) the dropping slope characteristics are decided by the chamfer of spool and the dynamic characteristics of the spool.