• 마이크로전자및패키징학회지
• /
• 제8권1호
• /
• pp.45-51
• /
• 2001

UBM층과의 젖음 특성 및 표면 산화정도가 미세 피치를 갖는 저 융점 솔더 범프의 볼 형성에 미치는 영향을 연구하였다. Au/Cu/Cr 과 Au/Ni/Ti UBM 위에 공정 조성에 가까운 In-Ag와 공정 조성의 Bi-Sn 솔더를 솔더 층의 증착 순서를 달리하여 증발 증착한 후 lift-off 공정과 열처리 공정을 사용하여 솔더 범프를 형성하였다. In-Ag솔더의 경우 In이 UBM 층과 접한 범프가, 또한 Bi-Sn 솔더의 경우 Sn을 먼저 UBM층위에 먼저 증착시켜 리플로 한 범프가 솔더 볼 형성 경향이 다른 범프에 비해 높았다. 구형의 솔더 범프 형성 정도는 UBM 층과의 젖음 특성에 따라 크게 달라졌다.

• 마이크로전자및패키징학회지
• /
• 제7권2호
• /
• pp.63-68
• /
• 2000

This paper introduces the partial melting process for solder application and characterization of its possibility using off-eutectic Pb-Sn alloy. In order to show that the liquid phase in the semi-liquid state maintains the wettability as the single-phase liquid, the wetting balance test are conducted with varying temperatures and compositions. The results are then compared with the surface tension of liquid, both measured and calculated, to examine the correlation. The results from this investigation indicate that the partial melting can yield satisfactory solder joints as long as the liquid phase acquires sufficient chemical activity. At a condition where the partial melting is effective, a direct correlation between the wettability and the surface tension is found to exist. All alloys are found to show a reasonable wettability in semi-liquid state.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 Proceedings of 5th International Joint Symposium on Microeletronics and Packaging
• /
• pp.81-86
• /
• 2000

To evaluate the possibility of the partial melting soldering. wettability of partial melted solders was measured using wetting balance. Off eutectic Sn-Pb allows are wettable in their partial melting zone. Especially, Pb rich alloys showed excellent wettability while wettability of Sn rich alloys were adequate or poor. It is found that wettability increases over $200^{\circ}C$ regardless of composition liquid fraction and phases of the original alloy Sn-7Ag alloy showed good wettability in their partial melting zone, while Sn-65Bi alloy was non-wettable under their melting points.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.791-797
• /
• 2002

This paper introduces the partial melting process for solder application and characterization of its feasibility using Sn-Ag, and Sn-Cu solder alloys. ill order to show that the liquid phase in the semi-liquid state maintains the similar wettability as single-phase liquid, the wetting balance tests are conducted with varying temperatures and compositions. Also, as a new soldering technology, the microstructural and mechanical test were investigated. The results from this research indicate that the partial melting can yield satisfactory sider joints as long as the liquid phase acquires sufficient chemical activity. At a condition where the partial melting is effective, a direct correlation between the wettability and the surface tension is found to exist.