• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1072-1076
• /
• 2017

In this paper, a numerical study has been performed to analyze flow characteristics of rocket propulsion. Through the ground spin test, combustion chamber pressure was measured. Based on the experimental results, numerical analysis was conducted under various nozzle pressure ratio conditions such as standard, operating and base pressure conditions. And it was compared with quasi-1D solution and experimental result. In addition, the difference in thrust characteristics according to the spin/non-spin of the flow conditions was confirmed at the same nozzle pressure ratio.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.8
• /
• pp.1-9
• /
• 2002

Axisymmetric separated flows in a converging-diverging conical nozzle are investigated through numerical simulations for various pressure ratios. We employ AUSM scheme for spatial derivatives and Pulliam's 2nd order subiteration time stepping scheme for implicit time integration. Numerical results indicate that the separated flow structures are very complex when compared to the simple quasi-one dimensional flow. Depending on the pressure ratio, the flow within the nozzle is either separated or non-separated. Various separated flow patterns with distinctive features are illustrated and discussed in detail.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.235-242
• /
• 2014

To investigate pressure distributions on the shaft surface of the air bearing, the commercial CFD software was employed to study three different nozzle geometries to improve the nozzle performance: general drill-shaped, matched cube-shaped and trimmed exit nozzles. Under the influence of stagnation point, the maximum pressure was observed at the center of shaft surface for all cases. Owing to the blocking effect of a fine gap between the shaft surface and the nozzle exit, the drill-shaped nozzle has the rapid local pressure increase near the nozzle exit corner, generating the ring vortex in the radial direction within pressure ratio of 6.92, and its pressure becomes negative in a certain range of downstream. In comparison, the contoured nozzle showed a local pressure increase in the measured range of pressure ratios, but a negative pressure appeared within the pressure ratio of about 10. The trimmed nozzle was seemed to extend the high pressure zone near the stagnation point in the radial direction substantially, and no negative pressure was appeared in the whole range. Based on these observations, it is found that trimming nozzle exit becomes more effective for improving the performance than modifying the nozzle inside contour.

• Journal of ILASS-Korea
• /
• v.10 no.1
• /
• pp.24-34
• /
• 2005

Injection technology is one of the important technologies in a diesel engine. Many studies have done on the injection system. In this study, the fuel chamber geometry, the orifice ratio and the needle lift of the injection valve for a marine diesel engine are varied, and simulated. The result shows that the nozzle hole size has influence on the rail pressure and injection duration sensitively. The decrease of the static pressure at the nozzle hole entrance and the increase of the dynamic pressure on the outlet surface are occurred with the increase of the nozzle hole diameter. The highest dynamic pressure of the outlet was occurred at the needle lift of 0.4mm and the nozzle hole diameter of 0.328mm in this test nozzle.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.2
• /
• pp.78-86
• /
• 2006

This paper presents the performance test result of the 30-ton class turbopump turbine. Test has been conducted using high pressure cold air, The turbine overall performance has been measured for various pressure ratio and rotational speed settings. The nozzle-rotor clearance effect on turbine performance also has been tested for the four kinds of the nozzle-rotor clearance values. We found that turbine efficiency rated 51.1% at its design velocity ratio and pressure ratio of 13.5. We also found that turbine efficiency can be increased by 3.5% for approximately 1mm decrement of the nozzle-rotor clearance from its nominal value.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.357-361
• /
• 2010

When high-pressure gas is exhausted through nozzle exit to the atmosphere, expanded supersonic jet is formed with the Mach disk at a specific condition. In two-dimensional supersonic jets, the hysteresis phenomenon of the reflected shock waves is found to occur under quasi-steady flow conditions. Transitional pressure ratio between the regular reflection and Mach reflection in the jet is affected by this phenomenon. In the present study, experiments are carried out on internal flow in a supersonic nozzle to clarify the hysteresis phenomena for the shock waves and to discuss its interdependence on the rate of the change of pressure ratio with time. Flow visualization is carried out separately on the straight and divergent channels downstream of the nozzle throat section. The influence that the hysteresis phenomena have on the location of shock wave in a supersonic nozzle is also investigated experimentally.

• 한국가시화정보학회:학술대회논문집
• /
• 2006.12a
• /
• pp.145-148
• /
• 2006

In order to design a micro-thruster which controls the altitude of a space vehicle for a very long lifetime, the flow field should be analyzed considering the nozzle geometry and the difference between stagnation and environmental pressures and so on. This paper describes the axisymmetric non-reacted computational results which were carried out to understand the basic flow phenomena according to the high nozzle pressure ratio. The area ratio is about 56 and the diameter of a nozzle exit is about 0.46 inch. The Mach cell and waves are predicted well.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2862-2867
• /
• 2007

The steady non-reacted compressible flow field in a symmetric micro-thruster, which is used for the accurate attitude control of a satellite, is analyzed varying the nozzle pressure ratio (NPR) to investigate the plume characteristics. The nozzle throat diameter is 0.06 inch and the area ratio is 56. The recirculation region is found just behind the normal shock at the several NPRs due to the locally adverse pressure gradient along the nozzle centerline when the environmental pressure is atmospheric. This phenomenon, the cause of flow loss, is similar to the flow behind a blunt body. As NPR increases the location of Mach disk, characteristics of the normal shock, moves downstream and its strength increases. The Mach number distribution appears in a wave-type patter after the normal shock because oblique shocks are reflected on the shock boundaries especially when NPRs are very high.

• Journal of the Korean Society of Visualization
• /
• v.8 no.2
• /
• pp.31-39
• /
• 2010

Hysteresis is an effect by which the order of previous events influences the order of subsequent events. Hysteresis phenomenon of supersonic internal flows with shock waves has not yet been clarified satisfactorily. In the present study, experiments are carried out on internal flow in a supersonic nozzle to clarify the hysteresis phenomena for the shock waves. Flow visualization is carried out separately on the straight and divergent channels downstream of the nozzle throat section. Results obtained were compared with numerically simulated data. The results confirmed hysteresis phenomenon for shock wave in the Laval nozzle at a certain specific condition. The relationship between hysteresis phenomenon and the range of the rate of change of pressure ratio with time was shown experimentally. The existence of hysteretic behavior in the formation, both the location and strength, of shock wave in the straight part of the supersonic nozzle with a range of pressure ratio has also been confirmed numerically.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.6
• /
• pp.479-487
• /
• 2015

In a reflected shock tunnel, stagnation conditions of a nozzle are determined by the flow behind a reflected shock. When calculating the flow behind the reflected shock, unlike a shock tube, the flow leakage through the nozzle is to be considered. The analytical studies were done to find out the characteristics of the stagnation conditions of the nozzle with various nozzle throat size. Experiments and numerical simulations were also carried out for further understanding of the flow leakage effects. It was found that the nozzle stagnation pressure was diminished by the increase of the size of the nozzle throat. It was also found that the steady pressure in the stagnation were maintained well at the area ratio of the driven tube to the nozzle throat is 4.5.