• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• 제45권10호
• /
• pp.844-854
• /
• 2017

The Expansion-Deflection(E-D) nozzle is a nozzle that has a performance gain through the altitude compensation effect by changing the effective area within the nozzle according to the altitude. An E-D nozzle has been known to reduce the length of the nozzle and achieve the payload gain of the launch vehicle. Due to the potential advantages of an E-D nozzle, related research has been carried out in the United Kingdom, Germany, Australia and Europe etc. In the UK, the flow characteristics of the E-D nozzle and the performance comparison with the dual-bell nozzle which is altitude compensation nozzle were studied. In order to understand the transition characteristics of the E-D nozzle in DLR, the transition characteristics according to the nozzle pressure ratio change were analyzed. In Europe, numerical study using the E-D nozzle concept on upper stage of the launch vehicle Ariane 5 ESC-B was carried out to confirm the possibility of payload gain according to the nozzle length reduction. In this paper, research trends of an E-D nozzle performed outside the country are classified and analyzed according to their characteristics and utilized as basic data of E-D nozzle research in the future.

• Aerospace Engineering and Technology
• /
• 제1권1호
• /
• pp.163-172
• /
• 2002

The turbine system composed of a nozzle and a rotor is used to drive turbopumps while gas passes through the nozzle, potential energy is converted to kinematic energy, which forces the rotor blades to spin. In this study, an aerodynamic design of a turbine system is investigated using compressible fluid dynamic theories with some pre-determined design requirements (i.e.,pressure ratio, rotational speed, required power etc.) obtained from a liquid rocket engine (L.R.E.) system design. For simplicity of a turbine system, impulse-type rotor blades for open type L.R.E. have been chosen. Usually, the open-type turbine system requires low mass flow rate compared to the close-type system. In this study, a partial admission nozzle is adopted to maximize the efficiency of the close-type turbine system. A design methodology of the a turbine system has been introduced. Especially, a partial admission nozzle has been designed by means of simple empirical correlations between efficiency and configuration of the nozzle. Finally, a turbine system design for a 10 ton thrust level of L.R.E is presented.

• Journal of the Korean Solar Energy Society
• /
• 제34권4호
• /
• pp.45-50
• /
• 2014

In this paper, the Ocean Thermal Energy Conversion(OTEC) with vapor-vapor ejector is proposed newly. At this OTEC system, a vapor-vapor ejector is installed at inlet of condenser. The vapor-vapor ejector plays a very important role in increasing of the production work of low-stage turbine throughout the decrement of outlet pressure of ejector. The performance analysis is conducted for optimizing the system with HYSYS program. The procedure of performance analysis consists of outlet pressure of high turbine, the mass ratio of working fluid at separator, total working fluid rate, and nozzle diameters of vapor-vapor ejector. The main results is summarized as follows. The nozzle diameter is most important thing in this study. When each nozzle diameter of vapor-vapor ejector is 10 mm, the efficiency of OTEC system with vapor-vapor ejector shows the highest value. So it is necessary to set the optimized nozzle diameters of vapor-vapor ejector for achieving the high efficiency OTEC power system.

• Journal of the Korean Society of Propulsion Engineers
• /
• 제21권6호
• /
• pp.1-7
• /
• 2017

The performance of a MEMS solid propellant thruster was predicted and analyzed through internal ballistics model and CFD analysis. The nozzle throat was $416{\mu}m$, and the area ratio of the nozzle was 1.85. As a result of the internal ballistics model, chamber pressure increased up to 197 bar and the maximum thrust was 3,836 mN. In CFD analysis, the chamber pressure of the internal ballistics model was applied as the operating pressure, and the CFD model was divided into an adiabatic and a heat loss model. As a result, the maximum thrust of the adiabatic model was 14.92% lower than that of the internal ballistics model, and the effect of heat loss was insignificant.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제28권10호
• /
• pp.1231-1237
• /
• 2004

Determination of geometric design parameters of a second-throat type annual supersonic ejector is described. Tested geometric parameters were primary nozzle area ratio, cross-sectional area of second-throat, L/D ratio of second-throat and primary flow injection angle. Varying these four geometric parameters, we build a test matrix made of 81 test conditions, and experimental apparatus was fabricated to accommodate them. For each test condition, the stagnation pressure of primary flow and the static pressure of the secondary flow were measured simultaneously along with their transition to steady operation and finally to unstarting condition. Comparing the performance curve of every case focused on starting pressure, the unstarting pressure and the minimum secondary pressure, we could derive correlations that the parameters have on the performance of the ejector and presented the optimal design method of the ejector. Additional experiments were carried out to find effects of temperature and mass flow rate of the secondary flow.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.134-137
• /
• 2009

Combustion tests of a low thrust rocket engine was performed to get combustion characteristics, which used a high concentrated hydrogen peroxide and kerosene as the oxidizer and fuel. The engine consisted of multi injector(six coaxial swirl injectors), chamber, nozzle and catalyst ignition system. The test was carried out by changing O/F ratio from 3.8 to 11.0. The experimental results showed that combustion efficiency was highest at O/F ratio from 5 to 6 and pressure fluctuations of all the range were lower than 5%.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• 제33권6호
• /
• pp.64-70
• /
• 2005

The overall results of hot firing tests of fuel-rich gas generator with impinging injector at design and off-design points are described. The gas generator consists of an injector head with impinging injector, a water cooled combustor wall, a turbulence ring to enhance mixing, an instrument ring measuring temperature and pressure and a nozzle. The combustion tests were successfully performed without damage of gas generator. Test results show that the outlet temperature is not dependent on residence time of hot gas within 4～6msec but dependent on chamber pressure. The relation between outlet temperature and combustion efficiency resulting from measured pressure, mass flow rate and area of nozzle throat is shown. The overall O/F ratio is the critical parameter to determine the outlet temperature and the linear correlation between two parameters is established.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• 제31권5호
• /
• pp.87-92
• /
• 2003

In rocket systems, somtimes special devices or equipments are installed near the nozzle exit area where high temperature and pressure combustion gas flows. To pretect these subsystems from severe thermal environment, it is necessary to have accurate thermal data measured from the experimental liquid rocket firing test. Test variables were combustion pressure (200, 300, 400 psi) and mixture ratio (1.5, 2.0, 2.5) and quartz was used as a heat probe. Measurement technique used in this research can be also applied to measure the radiative heat flux inside the combustion chamber which is important imput data for the liquid rocket regenerative cooling system design.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• 제14권6호
• /
• pp.88-94
• /
• 2005

A swirl ratio of a charge in the cylinder could be calculated by measuring both the rotary speed of paddle and the intake air flow rate in the swirl measurement apparatus fur several positions of valve lift. The automation of the swirl ratio measurement for a cylinder head is achieved by controlling both the valve lift of cylinder head and a suction pressure of the surge tank, instead of controlling them manually. PID control of the surge tank pressure and positioning a valve lift of the cylinder head are also achieved by using two step motors, respectively. Rotating speed of a paddle are measured using an optical sensor and a counter. Flow rate are measured from ISA 1932 flow nozzle by reading a differential pressure gauge position using IEEE-1394 camera. Time to measure the swirl ratio for a port in the cylinder head is drastically reduced from an hour to 3 minutes by automation control of the apparatus.

• The KSFM Journal of Fluid Machinery
• /
• 제8권6호
• /
• pp.26-32
• /
• 2005

1.6 MW class supersonic partial admission impulse turbine has been designed and tested in Korea Aerospace Research Institute for the liquid rocket engine application. The test has been performed using a high pressure air source facility in KARI. For the turbine power absorption, a hydraulic dynamometer has been used. Appropriate similarity relations are used for the determination of test condition. Various settings of turbine pressure ratio and rotational speed are tested to investigate global turbine characteristics. From measured data, parameters related to the turbine design are derived and validated.