• Journal of Welding and Joining
• /
• v.13 no.1
• /
• pp.156-166
• /
• 1995

Experimental models which are able to determine the deviation between weld line and weaving center by measuring the weld current during welding were proposed for the gas metal arc welding process. The models were used for developing a weld seam tracking system which controls the weaving speed of a welding torch. However, it was revealed that the tracking result of the system is affected by the welding conditions. Thus an arc sensor system was developed by using fuzzy control approach for overcoming the difficulty of modelling the nonlinear process. The rule base and parameters of the fuzzy control system were determined on the basis of the results of experiments. This fuzzy control system has shown the successful tracking capability for the wide operating range of welding conditions.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.5
• /
• pp.221-229
• /
• 2003

This paper suggests a control algorithm of 3-phase 3-wire series active power filter. This suggested algorithm can compensate source harmonics and reactive power in 3-phase 3-wire power distribution systems. These harmonics are generated by nonlinear loads such as diode rectifiers and thyristor converters. This control algorithm extracts a compensation voltage reference from performance function without phase transformation. Therefore, this control algorithm is simpler than any other conventional control algorithms. 3-phase 3-wire series active power filters which have a harmonic voltage source and a harmonic current source are manufactured and experiments are carried out to verify the effectiveness of suggested control algorithm.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.89-96
• /
• 1997

A robust speed control scheme for a brushless DC(BLDC) motor using an adaptive input-output linearization technique is presented. By using this technique, the nonlinear motor model can be linearized in Brunovski canonical form, and the desired speed dynamics can be obtained based on the linearized model. This control technique, however, gives an undesirable output performance under the mismatch of the system parameters and load conditions. For the robust output response, the controller parameters will be estimated by a model reference adaptive technique where the disturbance torque and flux linkage are estimated. The adaptation laws are derived by the Popov's hyperstability theory and positivity concept. The proposed control scheme is implemented on a BLDC motor using the software of DSP TMS320C30 and the effectiveness is verified through the comparative experiments.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.606-610
• /
• 2001

Voltage harmonics resulting from current harmonics produced by the nonlinear loads have become a serious problem in many systems. Moreover momentary interruptions and voltage sags are responsible for many of the power quality problems found in typical industrial plants. In this paper, proposed power system using series active power filter is not only harmonic compensation but also harmonic isolation between supply and load, and voltage regulation and unbalance compensation. The effectiveness of the proposed system is verified through computer simulations and experiments

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.805-810
• /
• 2004

The model is verified thorough simulations and experiments. And then the developed model is applied to a half car model and automobile vibrations are analyzed. The effects of tire design parameters on the automobile vibration energy are investigated. The results from laboratory and field tests confirm the validity of the analytical model. The 17-DOF half-car model is built to analyze the automobile vibration. The characteristics of the nonlinear model for a shock absorber are applied to this model. The results from the present 17-DOF half car model incorporating the analytical tire model with tire design parameters, are compared with a 5-DOF half car model where the tire is modeled with linear springs. The results of the 17-DOF model are closed to experimental results. Using the 17-DOF model, the influences of tire design parameter are considered. According to the results of analyses, the vibrations at seat/body/wheel are predicted by simulation and experiment.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.1036-1043
• /
• 1987

The objective of this paper is to improve the transient response characteristics of hydraulic servosystem via a reduced-order observer which is modelled based upon the nonlinear hydraulic servosystem. The observer is a second order linear model and implemented using a 8 bit micro-computer. The performance of the observer-based hydraulic servosystem was investigated through the hybrid computer simulations and experiments. The result shows that the reduced-order observer can effectively improve the transient response characteristics of hydraulic servosystem.

• Journal of Mechanical Science and Technology
• /
• v.16 no.12
• /
• pp.1643-1651
• /
• 2002

Magnetic levitation systems are required to have a large operating range in many applications. As one method to solve this problem, Time Delay Control (TDC) is applied to a single-axis magnetic levitation system in this paper A reduced-order observer is utilized to estimate states excluding measurable states in the control law. The system consists of a square air-core solenoid and a circular permanent magnet attached on a plastic ball. Theoretical magnetic forces of the system are obtained on the basis of the location of the magnet around the solenoid. The magnetic levitation force is obtained by the experiment, and then compared with the theoretical one. As the results of the control experiments, the nonlinear controller (TDC : 1-2 ㎜) has a larger operating range than the linear controller (PD control : 1-1.4 ㎜), and is superior to linear. control in the robustness to the modeling uncertainty and the performance of the disturbance rejection.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.8
• /
• pp.1980-2000
• /
• 1993

The stresses and torque transmission capabilities of adhesively bonded circular, hexagonal and elliptical lap joints were analyzed by the finite element and compared with the experimental results. The adherends of the joints were composed of carbon fiber/epoxy composite shafts and steel shafts. In calculating the torque transmission capabilities, the linear laminate properties of the composite material and the nonlinear shear properties of the adhesive were used. Using this method, the torque transmission capabilities of adhesively bonded lap joints could be obtained within 10% error compared to the experimental results except some single lap joints. The experiments revealed that the hexagonal joint had the best torque transmission capability from the single lap joints and the double lap joint had better torque transmission than the single lap joint.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.12
• /
• pp.2179-2189
• /
• 2010

This paper deals with analytical techniques for performance evaluation of small scaled wind power generator with outer permanent magnet rotor. In part (1), using transfer relations theorem, magnetic field distribution characteristics by PM and armature reaction field are derived. Moreover, electrical parameters such as back-EMF, inductance and resistance are calculated from the obtained field characteristic equations. The proposed analytical techniques are validated by nonlinear finite element method using commercial software 'Maxwell' and performance experiments of the manufactured generator. In part (2), generating characteristics analysis such as constant speed characteristics and constant resistive load characteristics, and performance evaluation according to variation of wind speed will be accomplished using the derived electrical parameters.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.4 s.19
• /
• pp.61-69
• /
• 2004

This paper presents a new analytical method for estimating the location of a target using directional data. Based on a nonlinear programming (NLP) problem formulated for the line method, which is a well known algorithm for two-dimensional location estimation, we present a method to find an optimal solution for the problem. Then we present a two-stage method for better location estimation based on the NLP problem. In addition, another two-stage method is presented for location estimation problems in which different types of observers are used to obtain directional data based on the analysis of the maximum likelihood estimate of the target location. The performance of the suggested method is evaluated through simulation experiments, and results show that the two-stage method is computationally efficient and highly accurate.