• Geomechanics and Engineering
• /
• v.37 no.2
• /
• pp.179-187
• /
• 2024

In this paper, a unified time-dependent constitutive model of Darcy flow and non-Darcy flow is proposed. The influencing factors of flow velocity are discussed, which demonstrates that permeability coefficient is the most significant factor. Based on this, the dynamic evolution characteristics of water inrush during tunneling through fault fracture zone is analyzed under the constant permeability coefficient condition (CPCC). It indicates that the curves of flow velocity and hydrostatic pressure can be divided into typical three stages: approximate high-velocity zone inside the fault fracture zone, velocity-rising zone near the tunnel excavation face and attenuation-low velocity zone in the tunnel. Furthermore, given the variation of permeability coefficient of the fault fracture zone with depth and time, the dynamic evolution of water flow in the fault fracture zone under the variable permeability coefficient condition (VPCC) is also studied. The results show that the time-related factor (α) affects the dynamic evolution distribution of flow velocity with time, the depth-related factor (A) is the key factor to the dynamic evolution of hydrostatic pressure.

• Progress in Superconductivity
• /
• v.14 no.1
• /
• pp.24-29
• /
• 2012

$(TMTSF)_2BF_4$ containing non-centrosymmetric anions is well known to exhibit a metal insulator transition around 37 K by ordering of the anions with a $q_2$=(1/2, 1/2, 1/2) wave vector. We established pressure-temperature phase diagram of the $(TMTSF)_2BF_4$ compound and showed that it can belong to the general phase diagram of the $(TMTSF)_2X$ family. Application of hydrostatic pressure decreases the anion ordering transition temperature and the superconducting state is finally stabilized below 3.77 K under 7.7 kbar. Magnetoresistance measurement on the $(TMTSF)_2BF_4$ under 7.8 kbar is performed but neither the field-induced spin-density-wave state nor the rapid oscillation is observed up to 9 T.

• Steel and Composite Structures
• /
• v.19 no.1
• /
• pp.1-19
• /
• 2015

The buckling analysis is presented for non-homogeneous (NH) orthotropic truncated conical shells subjected to combined loading of axial compression and external pressure. The governing equations have been obtained for the non-homogeneous orthotropic truncated conical shell, the material properties of which vary continuously in the thickness direction. By applying Superposition and Galerkin methods to the governing equations, the expressions for critical loads (axial, lateral, hydrostatic and combined) of non-homogeneous orthotropic truncated conical shells with simply supported boundary conditions are obtained. The results are verified by comparing the obtained values with those in the existing literature. Finally, the effects of non-homogeneity, material orthotropy, cone semi-vertex angle and other geometrical parameters on the values of the critical combined load have been studied.

• KIEAE Journal
• /
• v.12 no.6
• /
• pp.23-28
• /
• 2012

Pressure distribution in the water supply system of an apartment complex consisting of 12 buildings and 635 units in total have been investigated numerically. The complex incorporates two zone booster pump system, and around a half of units have pressure reducing valves (PRVs) in them. Calculated hydrostatic pressure without the water flow were compared with their designed and measured counterparts, and they agreed quite well with each other. Then, the pressure and volumetric water flow rate at all units were analyzed, indicating that there are noticeable differences in pressure and flow rate in one unit to another, although the aforementioned minimization technologies of pressure deviation were employed. In order to further reduce the difference in the water flow rate, it is suggested that all the units in the complex have PRVs installed in their water supply system. The effect of setting pressure of the PRVs on the non-uniformity of the flow in each unit and on the reduction of total water supply for the apartment complex have been studied. With the same PRV setting pressure of 3.952 bar (or the gauge pressure of $3.0kg_f/cm^2$), it has been estimated that the suggested system improves the non-uniformity (the coefficient of variation) of the flow rate of apartment complex over the current system, from 8.02% to 6.66%, and reduces the total water supply, from $0.02804m^3/s$ to $0.02766m^3/s$.

• The Korean Journal of Food And Nutrition
• /
• v.30 no.5
• /
• pp.1113-1118
• /
• 2017

The objective of this study was to investigate the non-thermal sterilization effect of methods such as high hydrostatic pressure (HHP) and UV-irradiation (specifically with regard to the storage stability and shelf-life of carrot juice. The microbial counts of the non-sterilized product increased from 5.51 to 7.34 log CFU/mL up to the fifth day, and then decreased to 5.46 log CFU/mL at six days. UV-irradiation was increased from 2.37 to 4.92 log CFU/mL. HHP was maintained under the 3 log CFU/mL. The pH of UV-irradiation and HHP was maintained withing the range of 6.29~6.30 and 6.20~6.22 during storage. However, the pH arising from non-sterilization decreased from 6.31 to 4.49. The color of non-sterilization changed significantly during storage, but UV-irradiation and HHP were similar during storage. The ${\beta}$-carotene content of non-sterilization was noted to have decreased from 269.45 to $65.19{\mu}g/mL$ during storage. The UV-irradiation and HHP decreased from 263.46 and $268.35{\sim}281.16{\mu}g/mL$ to 243.42 and $244.09{\sim}269.29{\mu}g/mL$, respectively. In conclusion, these findings suggest that HHP can be used for the pasteurization, or sterilization, of carrot juice and the optimal condition is two minutes.

• Steel and Composite Structures
• /
• v.6 no.2
• /
• pp.87-101
• /
• 2006

The deformation and dynamic behavior mechanism of submerged shell-like lattice structures with membranes are in principle of a non-conservative nature as circulatory system under hydrostatic pressure and disturbance forces of various types, existing in a marine environment. This paper deals with a characteristic analysis on quasi-periodic and chaotic behavior of a circular arch under follower forces with small disturbances. The stability region chart of the disturbed equilibrium in an excitation field was calculated numerically. Then, the periodic and chaotic behaviors of a circular arch were investigated by executing the time histories of motion, power spectrum, phase plane portraits and the Poincare section. According to the results of these studies, the state of a dynamic aspect scenario of a circular arch could be shifted from one of quasi-oscillatory motion to one of chaotic motion. Moreover, the correlation dimension of fractal dynamics was calculated corresponding to stochastic behaviors of a circular arch. This research indicates the possibility of making use of the correlation dimension as a stability index.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.329-334
• /
• 1992

It has been shown that the application of hydrostatic pressure during superplastic forming of 8090A1 can prevent the cavitaiton normally encountered at atmospheric pressure and cavity growth rate factor .eta. in the plane strain state is greater than that in the equibiaxial stress state. .eta. value shows some difference compared to the theoretical value, which seems to be due to the continuous nucletion and coalescence of voids during superplastic deformation. Scatter of measured data of cavity volume fraction seems to be on preferential nucleation of viods on non-uniformly distributed second phase particles in the deforming matrix.

• Tribology and Lubricants
• /
• v.24 no.6
• /
• pp.343-348
• /
• 2008

In this paper, a CFD (Computational fluid dynamics) code, FLUENT is adopted to investigate accurate flow characteristics for a slipper bearing which is used swash plate type hydraulic axial piston pump. Static pressure and velocity distributions, and velocity vectors are plotted for different film thickness and slipper rotational velocity. In recess region, there exists a doughnut shaped vortex ring. The static pressure distributions are non-uniform and the flow fields are highly asymmetrical under bearing rotation. Therefore the numerical method adopted in this paper can be use in design of hydrostatic components and further studies are required.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.3 no.1
• /
• pp.20-26
• /
• 2011

A weakly nonlinear seakeeping methodology for predicting motions and loads is presented in this paper. This methodology assumes linear radiation and diffraction forces, calculated in the frequency domain, and fully nonlinear Froude-Krylov and hydrostatic forces, evaluated in the time domain. The particular approach employed here allows to overcome numerical problems connected to the determination of the impulse response functions. The procedure is divided into three consecutive steps: evaluation of dynamic sinkage and trim in calm water that can significantly influence the final results, a linear seakeeping analysis in the frequency domain and a weakly nonlinear simulation. The first two steps are performed employing a three-dimensional Rankine panel method. Nonlinear Froude-Krylov and hydrostatic forces are computed in the time domain by pressure integration on the actual wetted surface at each time step. Although nonlinear forces are evaluated into the time domain, the equations of motion are solved in the frequency domain iteratively passing from the frequency to the time domain until convergence. The containership S175 is employed as a test case for evaluating the capability of this methodology to correctly predict the nonlinear behavior related to wave induced motions and loads in head seas; numerical results are compared with experimental data provided in literature.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.26-29
• /
• 1999

The sectional forming analysis program for analyzing the hydroforming processes of axisymmetric sheet parts was tleveloped. The rigid-viscoplastic FEM formulation based on membrane theory was derived, wh~cta simi~ltaneously solve force equilibrium as well as non-penetration condition. Hill's non-quadratic normal anisotropic yield theory(1979) was used for material behaviour. For describing the liquid pressure iaction, the flexible tool concept was introduced. Isotropic hardening law was also assumed. To verify the \,alidity of the formulation, the stepped cup forming process as well as the hydrostatic bulging test were \imnlated. Simulation results agreed well with Finckenstein and experimental ones.