• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.4
• /
• pp.377-382
• /
• 2012

This paper presents a proof-of-concept study on the evaluation of torsional vibration isolation performance through in-situ output torque measurement by using a non-contacting magneto-elastic torque transducer installed in the vehicle driveline system. The de-trending processing is first conducted to extract the torsional vibration from the measured driveline output torque. In order to estimate the transmissibility, primary performance indicator of a vibration isolator, the magnitude of transmitted torsional vibration with different frequencies is compared. From the conservative estimation results, the torsional damper built in a lock-up clutch of a torque converter is identified to be a vibration isolator. The evaluation results show that the fluid damping by torque converter outperforms the vibration isolation function of a torsional damper, and the isolation performance needs to be enhanced.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3923-3927
• /
• 2010

Primary charging roller rotated with contacting surface of OPC drum and take charge OPC drum. Owing to this reason, primary charging roller is made by elasticity substance with electric conduction. Properties of charging and image is changed by class of coating, method of coating and environment. This study developed coating material and coating method to make Image Forming of High- quality.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.947-951
• /
• 2007

This paper is concerned with a new concept for the damper without neither a coil spring nor fluid. The new damper concept consists of the permanent magnets and the cylinder of the conducting material. The opposite pole magnets produces the repulsive forces and this is substituted for the coil spring. The relative motion between the magnets and conducting cylinder produces eddy currents thus resulting in the electromagnetic force, which turns out to be the damping force thus and is substituted for a damping fluid. This damper is called the eddy current damper(ECD). The important advantage of the proposed ECD is that it does not require the damping fluid and any external power and is non-contacting and relatively insensitive to temperature. In the present study, the proposed ECD was constructed and experiments were performed to investigate its dynamic characteristics. The experiments shows that the proposed ECD has the excellent damping ability.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.4
• /
• pp.68-75
• /
• 2012

This paper presents a study on the driveline output torque estimation using a discrete Kalman filter. The in-situ output shaft torque is first measured by a non-contacting magneto-elastic torque transducer. The linear state-space system equations are first derived and the discrete Kalman filter is designed based on the Kalman filter theory to recover the driveline output torque contaminated by random noises. In addition to using torque measurement, the estimation of the output torque using two angular velocities: the output and wheel, is also conducted. The experimental results show that the discrete Kalman filter can be effective for not only removing the random noise in output torque but also estimating the output torque without torque measurement.

• Tribology and Lubricants
• /
• v.14 no.1
• /
• pp.45-53
• /
• 1998

Friction and wear test for two kinds of Cu-based sintered metallic friction material against cast iron disk was carried out by plate-on-disk type friction and wear tester to investigate the friction and wear characteristics of brake system in severe condition. In this experimental study, the counter specimen was cast iron which is being used generally in brakes of heavy duty equipments. Test friction materials were A type which was manufactured by foreign company and B type by domestic company. Friction coefficient and wear volume were measured and compared with each other. The experiment was performed under room temperature. The worn surface of cast iron disk and friction material were observed by scanning electron microscope. The temperature of surface of disk was measured continuously by the non-contacting thermometer. It was found that A type friction material had stable friction coefficient over the wide range of sliding condition, but B type friction material had unstable friction coefficient and lower value of 0.2 under the severe sliding condition.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.79.4-79
• /
• 2002

Our goal is the development of a system that estimates the location of interested point in a room with accuracy and low cost. Non-contacting position estimating method is widely used in various areas. Among these methods, acoustic signal-based method is the cheapest and provides reasonably accurate estimation as a result of many research efforts. Most of the acoustic-signal-based three-dimensional location estimators such as 3D sonic digitizer are using the ultrasound, and are organized with two procedures; time-of-flight (TOF) estimation and localization estimation. Since the errors in estimating the TOF could be accumulated with that of localization estimate, accuracy of TOF estimate is as...

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.220-223
• /
• 1997

Moire topography method is a well-known non-contacting 3-D measuement method. Recently, the automatic 3-D measurement by moire topography has been required since the method was frequently applied to the engineering and medical fields. 3-D measurement using projection moire topography is very attractive because of it's high measuring speed and high sensitivity. In this paper, using two-wavelength method of projection moire topography tested to measuring object with the 2x-ambiguity problem. Experimental results prove that the proposed scheme is capable of finding absolute fringe orders, so that the 2x-ambiguity problem can be effectively overcome so as to treat large step discontinuities in measured objects.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.293-298
• /
• 1998

In surface grinding, the conditions of the grinding wheel give a significant effect on the ground workpieces comparing with other metal removal processes. In this paper, to assist the development, a non-contacting optical method is introduced to make in-process measurements of scattering intensities from laser beam during surface grinding processes. This show indications of changes in surface texture of wheel working surfaces. Also, in order to determine the dressing time monitoring method of grinding wheel in surface grinding, a three-dimensional computer simulation of the grinding operation has been attempted based on the contact mechanism and surface-shaping system between the grinding wheel and the workpiece. The optical dressing time is determined based on the amount of the grain wear and work surface roughness.

• Proceedings of the Korean Reliability Society Conference
• /
• 2002.06a
• /
• pp.245-251
• /
• 2002

Electronic Speckle Pattern Interferometry(ESPI) is one of optical technique to measure displacement precisely, uses CCD camera to show result image in real time. General ESPI system measures in-plane or out-of-plane displacement. Shearography is one of electronic speckle pattern interferometric methods which allow full-field observation of surface displacement derivatives and it is robust in vibration. The shearography provides non-contacting technique of evaluating defects nondestructively In this study, the shearography was used to evaluate defects in Carbon Fiber Reinforced Plastic(CFRP). Various sizes of artificial defects were embedded in various depths of woven CFRP plate. Effects due to the variation of size and depth of defects were evaluated in this study.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.204-205
• /
• 2000

본 연구에서는 반도체 레이저 LD 혹은 백색광로부터 조사되는 빔을 CRT 모니터의 측정부에 입사시켜 패널 glass와 섀도우 마스크에서 반사되는 빔을 PSD에 조사하여 섀도우 마스크의 진동을 측정하였으며, CCD를 사용하여 열적변형과 패널 glass의 아랫면과 섀도우 마스크사이의 간격 Q값을 측정하였다. 사용한 PSD는 검출 영역은 12mm, 센서의 위치분해능은 0.2$mu extrm{m}$이며, 실시간적으로 처리할 수 있는 장점을 갖고 있다. CRT의 경우 전자빔의 충돌에 의한 섀도우 마스크의 열적 변형과 진동에 의한 섀도우 마스크의 떨림이 발생하여 화질이 저하된다. Q값의 정확한 계측과 섀도우 마스크의 열적변형 및 진동의 측정을 통하여 이들 현상이 발생되는 근본적인 취약구조를 발견함으로써 우수한 섀도우 마스크를 설계하고 제품의 성능을 향상시킬 수 있다. (중략)