• Journal of applied mathematics & informatics
• /
• v.41 no.1
• /
• pp.51-70
• /
• 2023

The flow of an incompressible Ellis fluid in an inclined asymmetric channel, driven by peristaltic waves was studied under low Reynolds number and long wavelength assumptions. The wave on each side of the channel are assumed to be an infinite train of sinusoidal waves, both having the same constant wave speed and wavelength however, they vary in wave amplitude, channel half width and phase angle. We derived expressions for the axial and transverse velocities, volume flow rate, pressure rise per unit wavelength and streamlines. The effects of varying the wave amplitudes, the phase angle, the channel width, the angle of inclination of the channel as well as the fluid parameters on the flow were analyzed. Trapping conditions were determined and the presence of reflux highlighted using the streamlines for the necessary channel and fluid conditions. By varying the fluid parameters, changes in the fluid that deviated from the Newtonian case resulted in a reduction in the axial velocity in the neighborhood of the center of the channel and a simultaneous increase in the velocity at the periphery of the channel. A nonlinear relation was observed with the pressure rise and the volume flow rate. This nonlinear relation is more pronounced with an increase in the absolute value of the volume flow rate. For Newtonian fluids a linear relation exists between these two variables. The fluid parameters had little effects on the streamlines. However, variations of the wave amplitudes, volume flow, channel width and phase angle had greater effects on the streamlines and hence the trapped region.

• Korea-Australia Rheology Journal
• /
• v.20 no.4
• /
• pp.189-196
• /
• 2008

The pulsatile flow of blood through a stenosed artery under the influence of external periodic body acceleration is studied. The effect of non-Newtonian nature of blood in small blood vessels has been taken into account by modeling blood as a Casson fluid. The non-linear coupled equations governing the flow are solved using perturbation analysis assuming that the Womersley frequency parameter is small which is valid for physiological situations in small blood vessels. The effect of pulsatility, stenosis, body acceleration, yield stress of the fluid and pressure gradient on the yield plane locations, velocity distribution, flow rate, shear stress and frictional resistance are investigated. It is noticed that the effect of yield stress and stenosis is to reduce flow rate and increase flow resistance. The impact of body acceleration is to enhance the flow rate and reduces resistance to flow.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.196-201
• /
• 2001

In this paper, we have described the microchannel fluid behavior in a slot between rotating curvilinear surfaces of revolution using micropolar fluid theory. ]n order to solve this problem, we have used boundary layer equations and applied non-zero values of the microrotation vector on the wall. The results are compared with the corresponding flow problems for Newtonian fluid. Results show that both the velocity distribution and the microrotation component distribution for a micropolar fluid are lower than that of a Newtonian fluid.

• Transactions of Materials Processing
• /
• v.8 no.2
• /
• pp.188-199
• /
• 1999

Semi-Solid Forming Process(Thixoforming, Rheocasting) is a novel forming process which has some advantages compared with conventional die casting, squeeze casting and hot/cold forging. In this study. Thixoforming process was selected as analysis processing in terms of billet handling and easiness of automation process. The Thixoforming process consists of reheating process of billet, billet handling, filling inot the die cavity and solidification of SSM part. In filling process, two rheology models which were Newtonian and Non-Nettonian model (Ostwald-deWaele)were verified with experimental results. The Ostwald-deWaele model shows the good agreement to the real flow and filling phenomena in die cavity. To give a boost the economical efficiency of Thixoforming process and to ensure the good forming result, reheating device coupled die set was proposed and the initial billet temperature for system that was found from experimental resluts. This study presents an overview of application of numerical analysis for simulation of semi-solid metal forming process to reduce the lead time for development of manufacturing part in industrial field.

• Smart Structures and Systems
• /
• v.2 no.1
• /
• pp.61-80
• /
• 2006

The concept of structural vibration control is to absorb vibration energy of the structure by introducing auxiliary devices. Various types of structural vibration control theories and devices have been recently developed and introduced into mechanical systems. One of such devices is damper employing controllable fluids such as ElectroRheological (ER) or MagnetoRheological (MR) fluids. MagnetoRheological (MR) materials are suspensions of fine magnetizable ferromagnetic particles in a non-magnetic medium exhibiting controllable rheological behaviour in the presence of an applied magnetic field. This paper presents the modelling of an MRfluid damper. The damper model is developed based on Newtonian shear flow and Bingham plastic shear flow models. The geometric parameters are varied to get the optimised damper characteristics. The numerical analysis is carried out to estimate the damping coefficient and damping force. The analytical results are compared with the experimental results. The results confirm that MR damper is one of the most promising new semi-active devices for structural vibration control.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.16 no.3
• /
• pp.181-192
• /
• 2012

Here in this paper, the steady paint film flow on a vertical wall of a non-Newtonian pseudo plastic fluid for drainage problem has been investigated. The exact solution of the nonlinear problem is obtained for the velocity profile. Also the average velocity, volume flux, shear stress on the wall, force to hold the wall in position and normal stress difference have been derived. We retrieve Newtonian case, when material constant ${\mu}_1$ and relaxation time ${\lambda}_1$ equal zero. The results for co-rotational Maxwell fluid is also obtained by taking material constant ${\mu}_1$ = 0. The effect of the zero shear viscosity ${\eta}_0$, the material constant ${\mu}_1$, the relaxation time ${\lambda}_1$ and gravitational force on the velocity profile for drainage problem are discussed and plotted.

• Journal of the Korean Institute of Gas
• /
• v.2 no.4
• /
• pp.53-59
• /
• 1998

Flow pattern of air-water two phase flow depends on the conditions of pressure drop, void fraction, and channel geometry. Drag reduction in the two phase flow can be applied to the transport of crude oil, phase change systems such as chemical reactor, pool and boiling flow, and to present cavitation which occurs in pump impellers. But the research on drag reduction in two phase flow is not intensively investigated. Therefore, experimental investigations have been carried out to analyze the drag reduction produced and void fraction by Co-polymer(A611p) addition in the two phase flow system. We find that the maximum point position of local void friction moves from the wall of the pipe to the center of the pipe when polymer concentration increases. Also we find that the polymer solution changes the characteristics of the two phase flow. And then we predict that it is closely related with the drag reduction.

• Journal of the Korean Society of Visualization
• /
• v.12 no.2
• /
• pp.18-22
• /
• 2014

Caenorhabditis elegans (C. elegans) is an undulatory nematode which exhibits two distinct locomotion types of swimming and crawling. Although in its natural habitat C. elegans lives in a non-Newtonian fluidic environment, our current understanding has been limited to the behavior of C. elegans in a simple Newtonian fluid. Here, we present some experimental results on the penetrating behavior of C. elegans at the interface from liquid to solid environment. Once C. elegans, which otherwise swims freely in a liquid, makes a contact to the solid gel boundary, it begins to penetrate vertically to the surface by changing its stroke motion characterized by a stiffer body shape and a slow stroke frequency. The particle image velocimetry (PIV) analysis reveals the flow streamlines produced by the stroke of worm. For the worm that crawls on a solid surface, we utilize a technique of traction force microscopy (TFM) to find that the crawling nematode forms localized force islands along the body where makes direct contacts to the gel surface.

• Korea-Australia Rheology Journal
• /
• v.21 no.2
• /
• pp.119-126
• /
• 2009

A numerical analysis is performed to investigate the effect of rotation on the blood flow characteristics with four different angular velocities. The artery has a cylindrical shape with 50% stenosis rate symmetrically distributed at the middle. Blood flow is considered a non-Newtonian fluid. Using the Carreau model, we apply the pulsatile velocity profile at the inlet boundary. The period of the heart beat is one second. In comparison with no-rotation case, the flow recirculation zone (FRZ) contracts and its duration is reduced in axially rotating artery. Also wall shear stress is larger after the FRZ disappears. Although the geometry of artery is axisymmetry, the spiral wave and asymmetric flow occur clearly at the small rotation rate. It is caused that the flow is influenced by the effects of the rotation and the stenosis at same time.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.10
• /
• pp.1146-1152
• /
• 2011

Ink transfer process is very important to determine quality of printed pattern, therefore its mechanism should be understood to control printing quality. Although there have been many attempts to understand ink transfer mechanism by numerical simulation and experimental studies, their model was too much simple to model realistic printing process and our understanding is not enough yet. In this paper we designed ink transfer visualization system to present flow visualization of ink transfer process for gravure offset printing. We considered rotational effect of blanket roll which is related with printing speed and used non-Newtonian fluid as working fluid such as Ag paste. For printing unit, cantilever-type blanket roll is used for convenient visualization of ink transfer. Serial images were captured continuously by using high-speed CMOS camera and long range microscope. We investigated the effects of various design parameters such as printing speed and pattern angle on the ink transfer process. We found more stretched ink filament for non-Newtonian fluid than Newtonian fluid. As increasing printing speed, length of stretched ink filament and height of break-up point are also increased. We also compared ink transfer process between CD and MD pattern and its relationship with ink transfer mechanism.