• Childhood Kidney Diseases
• /
• v.11 no.1
• /
• pp.112-117
• /
• 2007

Although juvenile nephronophthisis(NPHP) is one of the most frequent genetic causes of chronic renal failure, it has very rarely been reported in Korean children. Most NPHP patients are found to have chronic renal failure, since there are no distinct clinical symptoms for NPHP except polydipsia, polyuria and enuresis in the early stage of disease. Ten percent of NPHP patients manifest retinitis pigmentosa, called $Senior-L\ddot{o}ken$ syndrome. We experienced 2 cases of $Senior-L\ddot{o}ken$ syndrome that occurred in siblings(a 10 year-old boy and a 14-year-old girl) who were diagnosed with Leber's amaurosis. They were found to have severe renal impairment without polydipsia and polyuria. However, no large homogenous deletion of the NPHPI(2q13) gene was not identified in these patients. We report here on these cases and we review the literature to emphasize the association between Leber's amaurosis and the development of chronic renal failure.

• Journal of the Korea Concrete Institute
• /
• v.14 no.5
• /
• pp.766-773
• /
• 2002

The failure phenomenon of overlaid concrete structures, such as surface crack, and peel-off failure, shear bond failure in the end contact zone, was investigated due to humidity changes. To investigate this failure phenomenon, the surface tensile stress, and the shear stress, the vertical tensile stress in the contact zone were analysed using the non-linear stress-strain relationship of material such as strain-hardening- and strain-softening diagrams. Overlay thickness and overlay material were the main variables in the analyses. It is assumed that the initial surface humidity of overlaid concrete structures was 100％ r.H. With a atmospheric humidity of 55％ r.H. and two load cases for drying(LCI), curing and drying(LC2), the stress states of overlaid concrete structures were calculated. The result shows that only fictitious cracks occurred in the overlay surface of CM2O, ECM25, and no shear bond failure occurred in the contact zone without CM2O. The peel-off failure was proved to be the main cause of the damage in the overlaid concrete structures. Only for overlay thickness of 1cm occurred no peel-off failure in the case of drying after a long-term public use(LC1). In the case of curing and drying during overlay work(LC2) occurred the peel-off failure within 1.5days for all the overlaid concrete structures.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.29 no.2
• /
• pp.102-107
• /
• 2003

At orthodontic treatment, we have made every effort to get rigid anchorage which is not stirred when teeth move. As a result, the miniscrew that is rigid anchorage was invented recently, and now it is used widely. Concerning the advantage of miniscrew, it is reduced dependence of extraoral anchorage and it shortens treatment time for rapid tooth movement. In contrast, the defect of miniscrew is falling off it resulted from increasing of the mobility. So the purpose of this research is to be of help to prognose clinical use of miniscrew, which is inserted for intraoral anchorage, by investigating and comparing the failure rate of miniscrew for loading time. This study researches the failure rate of miniscrew for teeth movement at the orthodontic treatment. The failure rate of miniscrew in mid course, after inserting 147 miniscrews in 51 patients, is 13%(20/147). It showed no statistically significant differences as compared man with woman, maxilla with mandible, double-head with uni-head miniscrew, and drilling and non-drilling before inserting the miniscrew. In comparison below twenties with over twenties and the times that we give load to miniscrew, it produced that the failure rate of miniscrew is 9.7% higher in the case of below the twenties than over the twenties. Also, the failure rate of loading immediately is 10.8% higher than loading after 7 days. According to using driver for the insertion of miniscrew, the failure rate of miniscrew is higher in the case of using machined driver than in the case of using hand driver when the level of significance is 95%. According to the research, we can suppose that the failure rate has no concern with using miniscrew on man or woman, maxilla or mandible, the shape of head, and drilling or non-drilling before insertion of miniscrew. Therefore, we can choose eclectic miniscrew as demands. In addition, we must notify the patient, below twenties, to be possibility of high failure rate. And It is strongly recommended to give load after $1{\sim}2$ weeks for healing of the insertion area.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.4
• /
• pp.309-314
• /
• 2012

To assess the condition of stator insulation, nondestructive and overpotential tests were performed on four high voltage motors. The stator windings under these tests have nominal ratings of 6.6 kV. After completing nondestructive tests, the AC overvoltage applied to the stator windings was gradually increasing until insulation failure in order to obtain the breakdown voltage. No. 1, No. 2, No. 3 and No. 4 of 6.6 kV motors failed near rated voltage of 18.4 kV, 19.8 kV, 19.7 kV and 21.7 kV, respectively. The breakdown voltage of four motors was higher that expected for good quality coils(14.2 kV) in 6.6 kV motors. Almost all of failures were located in a line-end coil at the exit from the core slot. The breakdown voltages and the types of defects showed strong relation to the stator insulation tests such as in the case of AC current, dissipation factor($tan{\delta}$) and partial discharge magnitude.

• Restorative Dentistry and Endodontics
• /
• v.25 no.3
• /
• pp.399-406
• /
• 2000

The effect of inlay surface treatment on bonding was investigated when resin inlay was bonded to resin-modified glass-ionomer base with resin cement. For the preparation of glass-ionomer base, resin-modified glass-ionomer cement (Fuji II LC, GC Co., Japan) was filled in class I cavities of 7mm in diameter and 2mm in depth made in plastic molds. Eighty eight resin inlay specimens were made with Charisma$^{(R)}$ (Kulzer, Germany) and then randomly assigned to the four different surface treatment conditions: Group I, $50{\mu}m$ aluminium oxide sandblasting and silane treatment ; Group II, silane treatment alone ; Group III, sandblasting alone, and Group IV (control), no surface treatment. After a dentin bonding agent with primer (One-Step$^{TM}$, Bisco Inc., IL., U.S.A.) was applied to bonding surface of resin inlay and base, resin inlay were cemented to glass-ionomer base with a resin cement (Choice$^{TM}$, Bisco Inc., IL., U.S.A.). Shear bond strengths of each specimens were measured using Instron universal testing machine (4202 Instron, lnstron Co., U.S.A.) and fractured surfaces were examined under the stereoscope. Statistical analysis was done with one-way ANOVA and Dunkan's multiple range test. The results were as follows: 1. Sandblasting and silane treatment provided the greatest bond strength(10.56${\pm}$1.95 MPa), and showed a significantly greater bond strength than sandblasting alone or no treatment (p<0.05). 2. Silane treatment provided a significantly greater bond strength(9.77${\pm}$2.04 MPa) than sandblasting alone or no treatment (p<0.05). However, there was no significant difference in bond strength between sandblasting treatment and silane one (p>0.05). 3. Sandblasting alone provided no significant difference in bond strength from no treatment (p>0.05). 4. Stereoscopic examination of fractured surface showed that sandblasting and silane treatment or silane treatment alone had more cohesive failure mode than adhesive failure mode. 5. In relationship between shear bond strength and failure mode, cohesive failure occurred more frequently as bond strength increased.

• Structural Engineering and Mechanics
• /
• v.60 no.3
• /
• pp.387-404
• /
• 2016

In this paper, the response and failure of sharp-notched 6061-T6 aluminum alloy circular tubes with five different notch depths of 0.4, 0.8, 1.2, 1.6 and 2.0 mm subjected to cyclic bending were experimentally and theoretically investigated. The experimental moment-curvature relationship exhibits an almost steady loop from the beginning of the first cycle. And, the notch depth has almost no influence on its relationship. However, the ovalization-curvature relationship exhibits a symmetrical, increasing, and ratcheting behavior as the number of cycles increases. In addition, a higher notch depth of a tube leads to a more severe unsymmetrical trend of the ovalization-curvature relationship. Focusing on the aforementioned relationships, the finite element software ANSYS was used to continue the related theoretical simulation. Furthermore, the five groups of tubes tested have different notch depths, from which five unparallel straight lines can be observed from the relationship between the controlled curvature and the number of cycles required to produce failure in the log-log scale. Finally, a failure model was proposed to simulate the aforementioned relationship. Through comparison with the experimental data, the proposed model can properly simulate the experimental data.

• The Journal of Internal Korean Medicine
• /
• v.25 no.2
• /
• pp.368-378
• /
• 2004

In Oriental Medical theory, origin of kidney's weakness or atrophy is shen qi(腎氣) and function of san jiao(三焦) deteriorate, it result in a passage of evacuation is blocked. - In Oriental Medicine, Shen(腎) take charge of storing and evacuating function, by taking qi(氣) of the five viscera and the six bowels. - The cause of reducing of shen qi and san jiao's evacuative function is xu han(Emptiness and Coldness) of the five viscera and the six bowels' activity. So we do not treat only kidney, but we also must focus the five viscera and the six bowels' organic function and ying wei's function. A Renal Failure is similar in symptom to Kwan-kyuk(關格), oliguria or anuria, edema, Hu-son(虛損), Sin-pung(腎風) and Yuk-kuk(六極) in chenxiang(沈香). We grasp symptom of 7 cases of chronic renal failure, and diagnose its pathology based on Sa-jin(四診), and prescribed herbal medicines. And in the point of the chenxiang, we separate two group, Ater one is taken herbal medicine with chenxiang and the other is only taken herbal medicine with no using chenxiang, we compared the rate of treating with only herbal and herbal compounded chenxiang. We repeat medical examination for continuation of effective result, report clinical progress and result which based on this examination.

• Journal of Acupuncture Research
• /
• v.19 no.6
• /
• pp.49-60
• /
• 2002

Objective : The aim of this experiment is to investigate the effect of acupuncture and moxibustion at SP6(Sanyinjiao) and BL28(Pangguanshu) on uranyl acetate-induced acute renal failure in rats. Methods : To induce experimental acute renal failure, uranyl acetate was intraperitoneally injected to rats by 5mg/kg. 3 days later acupuncture and moxibustion treatment was done at SP6(Sanyinjiao) and BL28(Pangguanshu) bilaterally of the rats. And then 4 days later, we measured rats' body weight, kidney weight, serum BUN, creatinine and serum eletrolyte levels(Na, K and Cl). Results : In the moxibustion group, hypertrophy index of kidney and serum BUN level were decreased marginally significantly, and serum creatinine, K levels were decreased significantly. But in the acupuncture group, there was no significance at this experiment. Conclusions : SP6(Sanyinjiao) and BL28(Pangguanshu) moxibustion can decrease serum BUN, creatinine, and serum eletrolyte levels on uranyl acetate-induced acute renal failure in rats. And the study will be done continuously about non-effect in the acupuncture group at this experiment.

• Corrosion Science and Technology
• /
• v.4 no.5
• /
• pp.211-216
• /
• 2005

Failure analysis of the latch ram ball and the C-ram ball with the trade name AFBMA Gr. 50 Colmonoy No. 6, has been performed to identify the root cause of the failure. The study required the extraction of the both failed and normal balls from the nuclear fuel exchanger. Microstructures of both balls were examined after polishing and etching. Breaking tests of both the ball revealed similarity in cleavage surfaces. Fracture surfaces of both failed ball and normal ball after breaking test were examined with SEM and EDX. Microstructure of the ball revealed an austenite phase with coarse Cr rich precipitate. Indented marks observed on the surface of the failed ball are believed to be produced by overloading. In the light of the afore mentioned observations and studies, the failure mechanism of the ball in nuclear fuel exchanger seem to be caused by impact or mechanical overloading on ball.

• Journal of Chest Surgery
• /
• v.26 no.12
• /
• pp.915-919
• /
• 1993

The management of Patent Ductus Arteriosus[PDA] with heart failure and cardiac cachexia in premature infants have been a disturbing and controversial problem in the field of pediatric cardiovascular surgery.We analysed our experiences to determine the rationale of surgical closure of PDA in infants . During a period of 7 years from January 1986 to December 1992, 12 infants under 2 months of age underwent operations for "hemodynamically significant" PDA which had caused severe heart failure.There were 6 male and 6 female patients. Their mean gestational age was 33.8 weeks and their mean body weight was 1990 g. ranged from 710 g. to 2900 g. Mean age at operation was 28.5days. Seven patients had history of Indomethacin trial. All patients were operated with double ligation technique under general anesthesia.There was no mortality and blood transfusion was not necessary in any patient during the operation.In all cases, we could confirm the complete closure of PDA after operation by follow-up echocardiography.Two patients died during their hospital stay and 1 patient died at 6 months after operation. The causes of death were sepsis with congestive heart failure, necrotizing entero colitis and pneumonia respectively.We can not detect any operation related complication which resulted in permanent sequelae as well as delayed complications related to nerve damage. These results indicate that surgical ligation of PDA in infants with severe heart failure is relatively safe and effective.effective.