• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1996.11a
• /
• pp.6-6
• /
• 1996

Ceramic based nanocomposite, in which nano-sized ceramics and metals were dispersed within matrix grains and/or at grain boundaries, were successfully fabricated in the ceramic/cerarnic and ceramic/metal composite systems such as $Al_2O_3$/SiC, $Al_2O_3$/$Si_3N_4$, MgO/SiC, mullite/SiC, $Si_3N_4/SiC, $Si_3N_4$/B, $Al_2O_3$/W, $Al_2O_3$/Mo, $Al_2O_3$/Ni and $ZrO_2$/Mo systems. In these systems, the ceramiclceramic composites were fabricated from homogeneously mixed powders, powders with thin coatings of the second phases and amorphous precursor composite powders by usual powder metallurgical methods. The ceramiclmetal nanocomposites were prepared by combination of H2 reduction of metal oxides in the early stage of sinterings and usual powder metallurgical processes. The transmission electron microscopic observation for the $Al_2O_3$/SiC nanocomposite indicated that the second phases less than 70nm were mainly located within matrix grains and the larger particles were dispersed at the grain boundaries. The similar observation was also identified for other cerarnic/ceramic and ceramiclmetal nanocornposites. The striking findings in these nanocomposites were that mechanical properties were significantly improved by the nano-sized dispersion from 5 to 10 vol% even at high temperatures. For example, the improvement in hcture strength by 2 to 5 times and in creep resistance by 2 to 4 orders was observed not only for the ceramidceramic nanocomposites but also for the ceramiclmetal nanocomposites with only 5~01%se cond phase. The newly developed silicon nitride/boron nitride nanocomposites, in which nano-sized hexagonal BN particulates with low Young's modulus and fracture strength were dispersed mainly within matrix grains, gave also the strong improvement in fracture strength and thermal shock fracture resistance. In presentation, the process-rnicro/nanostructure-properties relationship will be presented in detail. The special emphasis will be placed on the understanding of the roles of nano-sized dispersions on mechanical properties.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.119-126
• /
• 1999

The rolling fatigue lives (RFL) of five kinds of silicon nitride balls were investigated. Four kinds of Si$_3$N$_4$ balls were fabricated using different raw materials, sintering aids and sintering conditions, Commercially available Si3N4 ball was also studied for comparison. All the balls were finished up to the dimensional accuracy of Grade 10 defined in KS B 2001 (Steel Balls for Ball Bearings) with a size of 9.525mm. RFL tests were then conducted under the initial theoretical maximum contact stress 6.38 GPa and the spindle speed 10,000 rpm. Gear oil was provided by oiled race as lubricant. The results of RFL test indicated the prerequisitic conditions for the long rolling life of Si$_3$N$_4$ball : (1) the high density, (2) mjcrostructures consisted of small uniformly distributed grains, (3) little glassy phase in grainboundary, and (4) little crystalline phase and secondary phase that induces residual thermal stress due to the differences of thermal expansion coefficient with Si$_3$N$_4$Phase.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.2
• /
• pp.222-226
• /
• 1998

Borazine (B3N3H6) as an inorganic analogue of benzene was synthesized by reaction of cheap raw materials (NaBH4 and (NH4)2SO4), and by using simple glass reaction apparatus in a scale up to 20 g per run with highly improved yield over 50%. It appears that synthesis of borazine is competing with formation of poly(aminoborane) as an inorganic analogue of polyethylene. The synthesized borazine and its polymerized product were characterized by comparison with products obtained from a commercial one. Bulk pyrolysis of the borazine polymer to 1500 ℃ produced a pure boron nitride (BN) with 75% ceramic yield, which displayed good oxidation resistance under dry air.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.324-331
• /
• 2014

The dispersion characteristics of AlN-4.5 wt% $Y_2O_3$ powder mixture by various dispersants were investigated in ethanol and methyethly-ketone (MEK) solvents. In general, the cationic polymer dispersants demonstrated superior dispersion of the powder as compared to the non-ionic ester-type dispersants or anionic phosphate-ester-based ones. The dispersion performance of the cationic polymer dispersants was sensitive to the type of solvent. An anhydric maleic-acid-based graft copolymer dispersant, AFB-1521, demonstrated a very good dispersion capability in ethanol but exhibited a much inferior dispersion in MEK. On the other hand, the dispersion of the powder mixture was very good with a phosphate-ester-based block polymer dispersant, BYK-111, in MEK solvent, while dispersionwas much degraded in ethanol.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.505-509
• /
• 2009

In this study, bulk nano-crystalline $Si_3N_4$ ceramics were fabricated by spark plasma sintering (SPS) and their mechanical properties, in particular wear, were investigated. A wide range of grain sizes, from 80 nm and 250 nm were obtained by varying sintering conditions ($1550^{\circ}C$-5 min to $1650^{\circ}C$-20 min). The elastic modulus of obtained ceramics was ${\sim}250$ GPa and hardness was in the range of $13{\sim}14$ GPa. The indentation fracture toughness increased from $2.58MPa{\cdot}m^{1/2}$ to $3.24MPa{\cdot}m^{1/2}$ with increasing sintering temperature possibly due to the elongated grains. Sliding wear tests revealed at least an order magnitude improvement in wear resistance with grain refinement. Microstructure analysis indicated that nano-$Si_3N_4$ specimens worn mainly through delamination and microcracking, while that of coarser specimens revealed severe wear with grain debonding and fracture.

• Journal of the Korean Ceramic Society
• /
• v.46 no.3
• /
• pp.225-228
• /
• 2009

The processing and characterization of ceramic nanocomposites, which produce bulk nanostructures with attractive mechanical properties, have been emphasized and introduced at Prof. Mukherjee's Lab at UC Davis. The following subjects will be introduced in detail in Part II, III, and IV. In Part II, the paper will describe a three-phase alumina-based nanoceramic composite demonstrating superplasticity at a surprisingly lower temperature and higher strain rate. The next part will show that an alumina-carbon nanotube-niobium nanocomposite produced fracture toughness values that are three times higher than that of pure nanocrystalline alumina. It was possible to take advantage of both fiber-toughening and ductile-metal toughening in this investigation. In the fourth section, discussed will be a silicon-nitride/silicon-carbide nanocomposite, produced by pyrolysis of liquid polymer precursors, demonstrating one of the lowest creep rates reported so far in ceramics at the comparable temperature of $1400^{\circ}C$. This was first achieved by avoiding the oxynitride glass phase at the intergrain boundaries. One important factor in the processing of these nanocomposites was the use of the electrical field assisted sintering method. This allowed the sintering to be completed at significantly lower temperatures and during much shorter times. These improvements in mechanical properties will be discussed in the context of the results from the microstructural investigations.

• Journal of Welding and Joining
• /
• v.28 no.6
• /
• pp.35-39
• /
• 2010

Generally, ceramic material is very difficult to machine due to high strength and hardness. However, ceramic material can be machined at high temperature by plastic flow as metallic material due to the deterioration of the grain boundary glassy phase. Recently, a new method was developed to execute cutting process with CBN cutting tool by local heating of surface with laser. There are various parameters in LAM because it is a complex process with laser treatment and machining. During laser assisted machining, high power results in reducing of cutting force and increasing tool life, but excessive power brings oxidation of the surface. The effect of laser power, feed rate, cutting depth and etc. were investigated on the life of cutting tool. Chips were observed to find out suitable machining conditions. Chips of SSN had more flow-types than HIPSN. It means SSN is easier to machining. The life of cutting tool was increased with increasing laser power and decreasing feed rate and cutting depth.

• Journal of Powder Materials
• /
• v.25 no.6
• /
• pp.494-500
• /
• 2018

In this study, the effect of the content of $MgO-CaO-Al_2O_3-SiO_2$ (MCAS) glass additives on the properties of AlN ceramics is investigated. Dilatometric analysis and isothermal sintering for AlN compacts with MCAS contents varying between 5 and 20 wt% are carried out at temperatures ranging up to $1600^{\circ}C$. The results showed that the shrinkage of the AlN specimens increases with increasing MCAS content, and that full densification can be obtained irrespective of the MCAS content. Moreover, properties of the AlN-MCAS specimens such as microhardness, thermal conductivity, dielectric constant, and dielectric loss are analyzed. Microhardness and thermal conductivity decrease with increasing MCAS content. An acceptable candidate for AlN application is obtained: an AlN-MCAS composite with a thermal conductivity over $70W/m{\cdot}K$ and a dielectric loss tangent (tan ${\delta}$) below $0.6{\times}10^{-3}$, with up to 10 wt% MCAS content.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.1
• /
• pp.49-52
• /
• 2016

The effect of process parameters such as the growth pressure and temperature on the AlN crystal growth has been investigated. AlN crystal was grown onto 6H-SiC seed crystal using PVT (Physical Vapor Transport) method. Crystal properties and morphology of AlN crystal was changed with growth pressure and temperature. Raman analysis confirmed that AlN crystals with different orientation were successfully grown on SiC seed crystal.

• Journal of the Korean Ceramic Society
• /
• v.44 no.4 s.299
• /
• pp.189-193
• /
• 2007

Effect of additive composition on fracture toughness of in situ-toughened $SiC-Si_3N_4$ composites was investigated for five different additive compositions. The highest toughness $(6.4MPa{\cdot}m^{1/2})\;in\;SiC-Si_3N_4$ composites investigated herein was obtained when an Y-Mg-Si-Al-O-N oxynitride glass was used as a sintering additive. The improvement in fracture toughness was produced by enhanced bridging and deflection by $Si_3N_4$ grains.