• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3159-3161
• /
• 1999

This paper aims at developing remote control system to control and monitor distributed various devices through internet or information communication network. SNMP (Simple Network Management Protocol) and UPS (Uninterruptible Power Supply) are adopted for network management protocol and applied device, respectively. For controlling and monitoring distributed devices in real-time, Java-environment software is constructed. Also, general-use interface controller between network device and applied device is proposed. Finally, serial communication such as RS-232 and RS-485 is used between controller and applied device.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.88-92
• /
• 1999

This paper aims at developing remote contro system to control and monitor distributed various devices through internet or information communication network. SNMP (Simple Network Management Protocol) and rectifier operated in a row are adopted for network management protocol and applied device, respectively. For controlling and monitoring distributed devices in real-time java-environment software is constructed. Also general-use interface controller between network device and applied device is proposed. Finally, seria communication such as RS-232 and RS-485 is used between controller and applied device.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.8
• /
• pp.1463-1471
• /
• 2009

In this paper, a new algorithm of Integrated Volt/Var Control (IVVC) is proposed using Volt/Var control for the Distribution Automation System (DAS) based on the modeling of the distributed load and the distributed current. In the proposed, the load flow based on the modeling of the distributed load and the distributed current are estimated from constants of four terminals using the measurement of the current and power factor from a Feeder Remote Terminal Unit (FRTU). For Integrated Volt/Var Control (IVVC), the gradient method is applied to find optimal solution for tap and capacity control of OLTC (On-Load Tap Changers), SVR (Step Voltage Regulator), and SC (Shunt Condenser). What is more Volt/Var control method is proposed using moving the tie switch as well as IVVC algorithm using power utility control. In the case studies, the estimation and simulation network have been testified in Matlab Simulink.

• International Journal of Safety
• /
• v.5 no.2
• /
• pp.6-11
• /
• 2006

The time delay in servo control on LonWorks/IP Virtual Device Network (VDN) is highly stochastic in nature. LonWorks/IP VDN induced time delay deteriorates the performance and stability of the real-time distributed control system and hinders an effective preventive and predictive maintenance. Especially in real-time distributed servo applications on the factory floor, timely response is essential for predictive and preventive maintenance. In order to guarantee the stability and performance of the system for effective preventive and predictive maintenance, LonWorks/IP VDN induced time delay needs to be predicted and compensated for. In this paper position control simulation of DC servo motor using Zero Phase Error Tracking Controller (ZPETC) as a feedforward controller, and Internal Model Controllers (IMC) based on Smith predictor with disturbance observer as a feedback controller is performed. The validity of the proposed control scheme is demonstrated by comparing the IMC based on Smith predictor with disturbance observer.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.2771-2773
• /
• 2005

In network human-robot interaction, human can access services of a robot system through the network The communication is done by interacting with the distributed sensors via voice, gestures or by using user network access device such as computer, PDA. The service organization and exploration is very important for this distributed system. In this paper we propose a new agent-based framework to integrate partners of this distributed system together and help users to explore the service effectively without complicated configuration. Our system consists of several robots. users and distributed sensors. These partners are connected in a decentralized but centralized control system using agent-based technology. Several experiments are conducted successfully using our framework The experiments show that this framework is good in term of increasing the availability of the system, reducing the time users and robots needs to connect to the network at the same time. The framework also provides some coordination methods for the human robot interaction system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.10
• /
• pp.1051-1058
• /
• 2011

Unmanned autonomous forklifts have a great potential to enhance the productivity of material handling in various applications because these forklifts can pick up and deliver loads without an operator and any fixed guide. Especially, automation of pallet loading and unloading technique is useful for enhancing performance of logistics and reducing cost for automation system. There are, however, many technical difficulties in developing such forklifts including localization, map building, sensor fusion, control, and so on. This is because the system requires numerous sensors, actuators, and controllers that need to be connected with each other, and the number of connections grows very rapidly as the number of devices grows. This paper presents a vision sensorbased autonomous loading and unloading for network-based unmanned forklift where system components are connected to a shared CAN network. Functions such as image processing and control algorithm are divided into small tasks that are distributed over a number of microcontrollers with a limited computing capacity. And the experimental results show that proposed architecture can be an appropriate choice for autonomous loading in the unmanned forklift.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2419-2422
• /
• 2000

A distributed real-time system that is being used now is usually divided into three level : higher level, middle level, and lower level. The higher level network is usually called an information network, the middle level is called a control network, and the lower level is called a field network or a divice network. This dissertation suggests and implements a middle level network which is called PICNET-NP (Plant Implementation and Control Network for Nuclear Power Plant). PICNET-NP is based partly on IEEE 802.4 token-passing bus access methed and partly on IEEE 802.3 physical layer. For this purpose a new interface, a physical layer service translater, is introduced. A control network using this method is implemented and applied to a distributed real-time system.

• Proceedings of the KIEE Conference
• /
• 2004.05a
• /
• pp.77-79
• /
• 2004

Because robot hardware architecture generally is consisted of a few sensors and motors connected to the central processing unit, this type of structure is led to time consuming and unreliable system. For analysis, one of the fundamental difficulties in real-time system is how to be bounded the time behavior of the system. When a distributed control network controls the robot, with a central computing hub that sets the goals for the robot, processes the sensor information and provides coordination targets for the joints. If the distributed system supposed to be connected to a control network, the joints have their own control processors that act in groups to maintain global stability, while also operating individually to provide local motor control. We try to analyze the architecture of network-based humanoid robot's leg part and deal with its application using the CAN(Controller Area Network) protocol.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.677-680
• /
• 2003

In this paper, the analysis of practical end-to-end delay in worst case is performed for distributed control system considering the implementation of the system. The control system delay is composed of the delay caused by multi-task scheduling of operating system, the delay caused by network communication, and the delay caused by the asynchronous between them. Through simulation tests based on CAN(Controller Area Network), the proposed end-to-end delay in worst case is validated. Additionally, online clock synchronization algorithm is proposed here for the control system. Through another simulation test, the online algorithm is proved to have better performance than offline one in the view of network bandwidth utilization.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.175-180
• /
• 2002

In order to satisfy the requirements of time reduction and cost saving for development of electronic control systems(ECU) in automotive industry, the applications of a standardized real-time operating system(RTOS) and a communication protocol to ECUs are increased. In this study, a body control module(BCM) that employs OSEK/VDX(open system and corresponding interfaces for automotive electronics/vehicle distributed executive) OS tour the RTOS and a controller area network(CAN) fur the communication protocol is designed, and the performances of the system are evaluated. The BCM controls doors, mirrors, and windows of the vehicle through the in-vehicle network. To identify all the transmitted and received control messages, a PC connected with the CAN communication protocol behaves as a CAN bus emulator. The control system based upon in-vehicle network improves the system stability and reduces the number of wiring harness. Furthermore it is easy to maintain and simple to add new features because the system is designed based on the standards of RTOS and communication protocol.