• The Journal of Advanced Prosthodontics
• /
• v.2 no.3
• /
• pp.111-115
• /
• 2010

PURPOSE. This study was conducted to evaluate clinical validity of a zirconia full-coverage crown by comparing zirconia's wear capacity over antagonistic teeth with that of feldspathic dental porcelain. MATERIALS AND METHODS. The subject groups were divided into three groups: the polished feldspathic dental porcelain group (Group 1), the polished zirconia group (Group 2), and the polished zirconia with glazing group (Group 3). Twenty specimens were prepared from each group. Each procedure such as plasticity, condensation, and glazing was conducted according to the manufacturer's manual. A wear test was conducted with 240,000 chewing cycles using a dual-axis chewing simulator. The degree of wear of the antagonistic teeth was calculated by measuring the volume loss using a three-dimensional profiling system and ANSUR 3D software. The statistical significance of the measured degree of wear was tested with a significant level of 5% using one-way ANOVA and the Tukey test. RESULTS. The degrees of wear of the antagonistic teeth were $0.119{\pm}0.059\;mm^3$ in Group 1, $0.078{\pm}0.063\;mm^3$ in Group 3, and $0.031{\pm}0.033\;mm^3$ in Group 2. Statistical significance was found between Group 1 and Groups 2 and between Group 2 and 3, whereas no statistical significance was found between Group 1 and Group 3. CONCLUSION. Despite the limitations of this study on the evaluation of antagonistic teeth wear, the degree of antagonistic tooth wear was less in zirconia than feldspathic dental porcelain, representing that the zirconia may be more beneficial in terms of antagonistic tooth wear.

• Korean Journal of Health Education and Promotion
• /
• v.13 no.2
• /
• pp.167-183
• /
• 1996

Human teeth vary widely in color. Practitioner and patients are concerned with preventing and correcting discolored or dark teeth to achieve and maintain stain-free, white teeth. Tooth brushing cannot alter tooth color but it can remove adhering films and stains. The esthetics of natural dentition can be improved by bleaching and this process can be applied to intrinsically and extrinsically stained teeth. The need for a brighter, more attractive smile has made rapid growth in the market for tooth whiteners. There is no doubt these products work as whiteners, at least on mild to moderate stains, but the safety of these products are unclear. In this experiment, the effect of tooth whitener application on the color and microhardness of extracted human enamel was measured. RMS, RMT and NWT were used as tooth whiteners, and tooth paste(ETQ) and hydrogen peroxide solution(HPO) were used as controls. 35 caries-free extracted human molars were embedded and polished with the exposed enamel diameter of 4 mm. The tooth whiteners and control agents were applied according to the manufacturers' instructions or clinically simulated procedures for eight weeks, and measurements were repeated every two weeks. Value(L＊) difference was measured using Differential Colorimeter(Model TC-6FX, Denshoku Co., Japan), and microhardness was measured using microhardness tester(Mitsuzawa Seiki Co., Japan). The results were as follows; 1. After application of agents for eight weeks, the Vickers hardness increased significantly in the ETQ, RMS and RMT application group(p〈0.01), and that decreased significantly in NWT application group(p〈0.01), but in HPO application group there was no significant change. The change in microhardness was greatest in NWT application group(p〈0.01). 2. After application of tooth whiteners and controls for eight weeks, the value change of toothpaste application group was significantly lower than those of other agents groups(p〈0.01), and there was no significant difference in value(L＊) change among tooth whitener groups(p〉0.01). 3. The application of tooth paste and paste type tooth whitener made gradual value change, but hydrogen peroxide gel type tooth whitener and hydrogen peroxide solution made rapid value change during initial application period.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.4
• /
• pp.407-421
• /
• 2012

Orthodontic problems of the oral maxillofacial area could be classified into skeletal and dental problems. Dental problems might cause various occlusal disharmony and among them congenital missing or eruption failure might cause not only functional problems but also esthetic problems. Additional psychological problems are also one of the reasons for patients seeking treatment. In cases showing eruption failure of many teeth in the maxilla, not only occlusal and esthetic problems but also difficulty in alveolar bone maintainment could occur. Therefore, successive approach is necessary when multiple teeth show eruption problems. In this case, a patient with eruption problems of #13, 12, 11, 23, 43 was successfully treated by surgical exposure and successive orthodontic extrusion resulting perfect occlusion. By additional periodontal treatment, gingival recession that occurred along with teeth eruption was solved. The impacted right mandibular canine was erupted successfully only by natural arch expansion and leeway space without any special surgical treatment.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.39 no.3
• /
• pp.146-157
• /
• 2023

The bite collapses due to posterior teeth loss or wear results in inadequate space for restoration and esthetic concerns. Increasing the occlusal vertical dimension to improve space deficiency rotates the mandible posteriorly, creating a gap between the maxillary and mandibular anterior teeth, leading to loss of anterior guidance. To solve this problem, the prosthodontics or orthodontics treatments are the commonly used methods for proper anterior guidance. However, it is reasonable to assume that the anterior teeth can naturally relapse to their original position when the occlusal force is eliminated. Therefore, this case report aimed to test whether natural relapse could recover the lost anterior guidance to develop a less invasive and more convenient treatment method. Digital superimposition was used to evaluate the changes in anterior teeth alignment to confirm the change of the recovered anterior guidance. The appropriate indications for this new treatment method were defined and applied clinically.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.3
• /
• pp.746-763
• /
• 1996

An alternative design to conventional class II cavity preparation for proximal carious lesions is the tunnel preparation. It preserves the marginal ridge intact, thus making it possible to maintain the natural contact relationship with the adjacent tooth and minimize tooth reduction. This in vitro study was purposed to evaluate the effect of the materials' elastic constants and shear-bond strength on the marginal ridge fracture resistance of teeth restored by the tunnel technique, and to find the materials of choice for tunnel restorations. $Resinomer^{(R)}$, $Ketac-silver^{(R)}$, $Miracle-Mix^{(R)}$, and Tytin were used as restorative material. The elastic constants of each restorative material were evaluated by ultrasonic pulse measurement. Young's modulus and bulk modulus of the restorative materials were evaluated in three specimens for each material type. The shear-bond strength of the restorative materials to the dentin surface was measured after thermocycling 400 times between 6 and $60^{\circ}C$, using ten specimens for each material type. For measuring marginal ridge strength, 60 sound extracted molar teeth were distributed into six groups by size. Sound molar teeth were used as a Control group and unfilled prepared teeth were grouped as Unrestored. Another four groups were named Resinomer group, Ketac-Silver group, Miracle Mix group, and Tytin group by type of restorative material. Tunnel cavity preparation was done with ' 1/2, 2, and 4 round burs in sequence. Initial access to proximal surface was made through an occlusal access preparation started at least 2mm from the marginal ridge, and the proximal opening was formed about 2.5mm below the marginal ridge. After restoration and thermocycling, marginal ridge strength was measured using a universal testing machine. The results were as follows: 1. The Young's modulus of $Tytin^{(R)}$ was 63.95 GPa, followed by $Ketac-Silver^{(R)}$ 27.60 GPa, $Miracle-mix^{(R)}$ 18.48 GPa, and $Resinomer^{(R)}$ 10.74 GPa showing significant differences between the groups(P<0.05). The bulk modulus of the materials showed the same order as Young's modulus. The value of $Tytin^{(R)}$ showed 59.57 GPa indicating that it will deform less than other materials under the same stress. It was followed by $Ketac-Silver^{(R)}$ 23.57 GPa, Miracle $Mix^{(R)}$ 12.50 GPa, and $Resinomer^{(R)}$ 11.60 GPa. 2. The Resinomer group had a shear-bond strength of 7.41 MPa which was significantly higher than those of the Ketac-Silver group (1.80 MPa) and the Miracle Mix group (2.84 MPa) (P<0.01). All the specimens of Tytin group detatched from the dentin surface during thermocycling. 3. The mean marginal ridge strength of the Unrestored group(46.14 kgf) was significantly lower than that of the Control group (84.24 kgf) (P<0.01). The marginal ridge strength of teeth restored by the tunnel technique was, in order, Ketac-Silver group 74.06 kgf, Miracle Mix group 73.36 kgf, Resinomer group 63.47 kgf, and Tytin group 58.76 kgf. The Ketac-Silver, Miracle Mix, and Resinomer groups showed no significant difference with the Control group (P>0.05), but the Tytin group showed significantly lower strength compared to the Control group(P<0.05). The results showed that the marginal ridge strength of the teeth restored by the tunnel technique was not significantly lower than that of sound teeth. They also demonstrated that the bonding strength of the restorative material to the tooth surface should be high and the modulus of elasticity should not be lower than that of the tooth in order to restore the marginal ridge strength to its natural condition.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.5
• /
• pp.479-489
• /
• 2008

Statement of the problem: Under anatomical limitations on maxillary posterior region, a poor crown-to root ratio acting on dental implants can result in undesirable stress in surrounding bone, which in turn can cause bone defects and eventual failure of implants. Purpose: The purpose is to compare stress distribution due to different crown-root ratio and effect of splinting between natural teeth and implants in maxillary molar area under different loads. Material and methods: Analysis of stress arising supporting bone of the natural teeth and the implant was made with 3-dimensional finite element method. The model simulated naturel teeth was made with 2nd premolar and 1st molar in the maxillary molar region (Model T). The model simulated implants placed on same positions with two parallel implants of Straumann Dental Implant cemented abutment (Model I). Each model was designed in different crown-root ratio (0.7:1, 1:1, 1.25:1) and set cement type gold crown to make it non-splinted or splinted. After that, 300 N force was loaded to each model in five ways (Load 1: middle of occlusal table, Load 2: middle of buccal cusp, Load 3: middle of lingual cusp, Load 4: horizontal load to buccal cusp of anterior abutment only, Load 5: horizontal load to middle of buccal cusp of each abutment), and stress distribution was analyzed. Results and conclusion: On all occasions, stress was concentrated at the cervical region of the implant. Under load 1, 2 and 3, stress was not increased even when crown-root ratio increases, but under load 4 and 5, when crown-root ratio increases, stress also increased. There was difference in stress values between natural teeth and implants when crown-root ratio gradually increases; In case of natural teeth, splinting decreased stress under vertical and horizontal loads. In case of implants, splinting decreased stress under vertical loads 1,2 and 3, but increased maximal stress under loads 2 and 3. Under horizontal loads, splinting decreased stress, however the effect of splinting decreased under load 5 than load 4. Furthermore, the stress was increased, when crown-root ratio is 1.25:1. Clinical implications: This limited finite element study suggests that the stress on supporting bone may be increased under non-axial loads and poor crown-root ratio. Under poor crown-root ratio, excessive stress was generated at the cervical region of the implant, and decreased splinting effect for stress distribution, which can be related to clinical failure.

• The Journal of the Korea Contents Association
• /
• v.16 no.2
• /
• pp.772-781
• /
• 2016

This study is to set the objective criteria on maxillary incisors shade selection by using the colorimetric Shade-Eye NCC as measuring in CIE $L^*$, $a^*$, $b^*$ values, and look into the meaning by analyzing its values. We explain the purpose of this study and gotten their agreement from patients visiting the dentist, 111 people's (men 50, women 61) three teeth, the maxillary central incisor, maxillary lateral incisor, maxillary canines, total of 333 teeth colorimetry. As a result of comparing the differences in colors between cervical margin and incisal edge, ${\Delta}E^*$ of canine is shown as low as $5.81({\pm}2.98)$, followed by lateral incisor of maxilla as $6.51({\pm}3.23)$ and central incisor of maxilla $7.51({\pm}3.04)$. Females show higher luminosity(L*) than males do in all teeth- central incisor, lateral incisor and canine; in yello chroma(b*) males' central incisor is slightly higher than that of females (p<0.05). Age significantly influences the luminosity and red (a*) and yellow chroma (b*) of central incisor(L*); the luminosity(L*), and yellow chroma(b*) of lateral incisor and canine (p<0.05). Smoking doesn't significantly influence the color of natural teeth. Drinking reduces the luminosity of central incisor as well as red chroma of lateral incisor(p<0.05). A chronic illness is likely to reduce the luminosity of central incisor and lateral incisor(p<0.05).

• Journal of dental hygiene science
• /
• v.21 no.2
• /
• pp.96-103
• /
• 2021

Background: We aimed to investigate the effect of Citrous limon extract (CLE) on oxidative stress-induced cytotoxicity and nitric oxide (NO) generation and the tooth bleaching effect of CLE as a substitute for hydrogen peroxide (H₂O₂) and determine the feasibility and application of CLE as a safe and effective natural tooth bleaching agent. Methods: The protective effect of CLE on H₂O₂-induced cytotoxicity in Raw264.7 macrophages was investigated by the MTT assay. The inhibitory effect of CLE on the generation of H₂O₂-induced NO was confirmed by the NO assay, and the changes in inducible nitric oxide synthase (iNOS) protein expression were confirmed by western blotting. Stained bovine teeth were treated with/without 15% and/or 35% CLE and H₂O₂, 15% sodium bicarbonate (NaHCO₃) for 3 hours, and were irradiated with/without bleaching light (BL) for 15 minutes. The color change of the treated bovine tooth surface was measured using a colorimeter. Results: The viability of Raw264.7 cells treated with each concentration of CLE and 500 μM H₂O₂ significantly increased as CLE increased, and NO generation and iNOS protein expression were significantly reduced in cells treated with 300 ㎍ CLE+/500 μM H₂O₂+ and 300 ㎍ CLE+/500 μM H₂O₂+/150 ㎍ NaHCO₃+. The bleaching effect of 35% CLE+ was higher than that of 15% CLE+ and 15% NaHCO₃+, and the effect was similar to that of 15% H₂O₂+. The 35% CLE+/15% NaHCO₃+ showed the greatest bleaching effect and was higher than that of the groups irradiated with the BL. The greatest bleaching effect was observed with 35% CLE+/15% NaHCO₃+, followed by 35% H₂O₂+/BL+. Conclusion: CLE inhibited oxidative stress-induced cytotoxicity and NO generation in Raw264.7 cells and, could replace H₂O₂, which causes side effects and risks in teeth breaching treatment. It showed greatest teeth bleaching effect when combined with NaHCO₃. CLE is an effective and safe natural tooth bleaching substitute.

• The Journal of Korean Academy of Prosthodontics
• /
• v.31 no.1
• /
• pp.129-150
• /
• 1993

Since the restoration or masticatory function is the most important aim of implants, it should be substituted for the role of natural teeth and deliver the stress to the bone under the continous load during function. In natural teeth, stress distribution can be obtained through enamel, dentin and cementum and the elasticity of the periodontal ligament play a role of buffering action. In contrast, implant prosthesis has a very unique characteristics that it delvers the load directly to bone through the implant and superstructure. This fact arise the needs to evaluate the stress distribution of the implant in the mechnical aspects, which has a similar role of natural teeth but different pathway of stress. With 3 kinds of implant in prevalent use, 2 types of experimental PEA implant models were made, axisymmetric and 2-dimensional type. In axisymmetric model, the stiffness of the part including the prosthesis and implant which extrude out of bony surface could be calculated with displacement of the superstructure un er 100N vertical load and then damping effects could be determined through this stiffness. In axisymmetric FEA model, load to the bone could be deduced by evaluation the stress distribution of the designed surface under the 100N vertical force and in 2-dimensional model, 100N eccentric vertical load and 20N horizontal loda. The result are as follows. 1. In every implant, stress to the bone tends to be concenturated on the cortical bone. 2. Though the stress of the cancellous bone is larger at the apex of implants, it is less compared with cortical bone. 3. Under 20N horizontal load, stress of the left and right sides of implant shows a symmetrical pattern. But under 100N eccentric vertical load, loaded side shows much larger stress value. 4. In the 1mm interface, stress distribution among implants tend to have a similar pattern. But under 20N horizontal load apposite side of being loaded shows less stress in IMZ. 5. In the case of screw type implant, stress tends to vary along with screw shape. 6. According to the result determined with microstrain, cancellous bone id generally under the condition of overload, while cortical bone is usually within the limitation of physiologic load. 7. In the Branemark implant, maximum stress to the cortical bone is larger than any other implant except for the condition of 20N horizontal force and 0.05mm interface. 8. Damping effects of implants is maximum in IMZ.

• The Journal of Korean Academy of Prosthodontics
• /
• v.35 no.2
• /
• pp.308-329
• /
• 1997

A lot of the research paper was reported about the result of influence of IMC (Intra-mobile connector) in the IMZ implant placed solely in the alveolar bone, but reports about the effect of IMC on functional load at state of connecting with natural teeth ere rare. The major propose of this study was find the mechanical character of IMC itself by using the finite element analysis program after simulated variance of condition connected with the natural teeth and implant on funcional load. When first and second premolar was lost, IMZ implant was placed with a diameter of 3.3mm and a length of 13mm with IMC in second premolar area. Rigid connection was done and the non-figid connention was located on the female part of the canine abutment and the implant respectively and then both the infraocclusion of $30{\mu}m$ and the non-infraocclusion under the load of 40kg applied to the portion of the natural teeth, the pontic and the implant. The displacement and the stress of it was estimated and analyzed IMC itself of the rigid connection and the non-rigid connection was grouped. The following result were obtained. 1. In all groups, the displacement of Y-axis was greater than that of X-axis and the aspect of displacement showed that IMC was displaced downward and to the center. 2. There was no differences in the displacement of IMC regardless of the connection type. 3. In the displacement of IMC, I 4 was the least, I 1 and I 3 are similar and I 2 was the greatest. 4. There was no differences in the peak value of maximal stress of IMC regardless of the connection type. 5. In the peak value of maximal stress of IMC, I 4 was the least, I 1 and I 3 were similar, and I 2 was the largest.