• Korean Journal of Metals and Materials
• /
• v.46 no.11
• /
• pp.755-761
• /
• 2008

We fabricated thermally evaporated 10 nm-Ni/1 nm-Ir/(poly)Si films to investigate the energy saving property of silicides formed by rapid thermal annealing (RTA) at the temperature range of $300{\sim}1200^{\circ}C$ for 40 seconds. Moreover, we fabricated 100 nm-thick ITO/(poly)Si films with an rf-sputter as references. A transmission electron microscope (TEM) and an X-ray diffractometer were used to determine cross-sectional microstructure and phase changes. A UV-VIS-NIR and FT-IR (Fourier transform infrared spectroscopy) were employed for near-IR and middle-IR absorbance. Through TEM analysis, we confirmed 20~65 nm-thick silicide layers formed on the single and polycrystalline silicon substrates. Ir-inserted nickel silicide on single crystalline substrate showed almost the same absorbance in near IR region as well as ITO, but Ir-inserted nickel silicide on polycrystalline substrate, which had the uniform absorbance in specific region, showed better absorbance in near IR region than ITO. The Ir-inserted nickel silicide on polycrystalline substrate particularly showed better absorbance in middle IR region than ITO. The results imply that nano-thick Ir-inserted nickel silicides may have excellent absorbing capacity in near-IR and middle-IR region.

• Korean Journal of Materials Research
• /
• v.13 no.2
• /
• pp.106-110
• /
• 2003

Nano-sized powders of Indium Tin Oxide(ITO) were synthesized by a coprecipitation method. In order to investigate the gas sensing characteristics in the nanocrystalline ITO thick films with various particle sizes, ITO powders with the average particle diameter of 15, 30, and 70 nm respectively were synthesized. And the sensitivity of ITO thick films was measured upon exposure to a target gas($C_2$$H_{5}$ /OH) and some other Volatile Organic Compounds(VOCs), such as, toluene, methanol, benzene, chloroform. As a result, ITO thick films had high sensitivity for ethanol and higher sensitivity with smaller particle size.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.23-23
• /
• 2010

The $Bi_2Mg_{2/3}Nb_{4/3}O_7$ (BMNO)-Bi composite films sandwiched by an $Al_2O_3$ protection layer exhibited a linear increase of a dielectric constant with increasing thickness and the 1000nm-thick BMNO-Bi composite films showed a dielectric constant (~220) higher than that of its bulk material (~210), keeping a low leakage current density of about $0.1{\mu}A/cm^2$. An enhancement of the dielectric constant in the BMNO-Bi composite films was attributed to the hybrid model combined by a space charge polarization, dipolar response, and nano-capacitors. On the other hand, 1000nm-thick BMNO-Bi composite films sandwiched by 40nm-thick BMNO layer exhibited a dielectric constant of about 450 at 100 kHz and a leakage current density of $0.1{\mu}A/cm^2$ at 6V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.444-445
• /
• 2007

IZO/Al multilayer anode films for flexible top emitting organic light emitting diodes (TOLEDs) were grown on PEN (polyethylen-enaphthelate) substrate using twin target sputter (TTS) system. To investigate electrical and optical properties of IZO/Al multilayer films, 4-point probe method and UV/Vis spectrometer were used, respectively. From a IZO/Al multilayer films with 100nm-thick Al, sheet resistance of $1.4{\Omega}/{\square}$ and reflectance of above 62% at a range of 500~550nm wavelength could be obtained, In addition, structural and surface properties of IZO/Al multilayer films were analyzed by XRD (X-ray diffraction) and FESEM (field emission scanning electron microscopy) and AES (auger electron spectroscope), respectively. Moreover, flexibility of IZO/Al multilayer anode films were examined by bending test method.

• Journal of the Korean Ceramic Society
• /
• v.45 no.7
• /
• pp.411-417
• /
• 2008

Aerosol Deposition Method (ADM) is a novel technique to grow ceramic thick films with high density and nano-crystal structure at room temperature. $^{1,2)}$ For these unique advantages of ADM, it would be applied to the fabrication process of 3-D integration ceramic modules effectively. However, it is critical to control the properties of starting powders, because a film formation through ADM is achieved by impaction and consolidation of starting powders on the substrates. We fabricated alumina thick films by ADM for the application to integral substrates for RF modules. When the as-received alumina powders were used as a starting material without any treatments, it was observed that the dielectric properties of as-deposited alumina films, such as relative permittivity and loss tangent, showed high dependency on the frequency. In this study, some techniques of powder pre-treatments to improve the dielectric properties of alumina thick films will be shown and the effects of starting powders on the properties of AD films will be discussed.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.6
• /
• pp.531-536
• /
• 2001

Co-22 %Cr alloy films are promising for high-density perpendicular magnetic recording media with their perpendicular anisotropy and large coercivity of 3000 Oe. We observed that a self organized nano structure (SONS) of fine ferromagnetic Co-enriched phase and paramagnetic Cr-enriched phase appears inside the grain of Co-Cr magnetic alloy thin films at the elevated substrate temperature after do-sputtering. The periodic fine Co-enriched phase and Cr-enriched phase is the plate shape of 80 (equation omitted)-wide and 1000 (equation omitted)-long. Cr-enriched phases are located at the center of grains. We prepared 5000 (equation omitted) -thick Co-22 %Cr films on polyimide substrate with varying substrate temperature of $ 30^{\circ}C$, $ 150^{\circ}C$ ,200 $^{\circ}C$, $300^{\circ}C$, and $400^{\circ}C$, respectively. A transmission electron microscope equipped with energy dispersive X-ray analyzer is employed to observe the microstructure of each samples after Co-enri-ched phase are etched selectively. The self organized nano structure of Co-enriched and Cr-enriched lamellar is observed above the substrate temperture of $150^{\circ}C$. No compositional change is observed with substrate temperature. The compositional phase separation in self organized structure becomes clear as the substrate temperature increases. Our results implies that the self organized nano structure in Co-22 %Cr film is ideal for ultra high density recording media by recording selectively on Co-enri-ohed phase.

• Journal of the Korean Ceramic Society
• /
• v.49 no.1
• /
• pp.95-99
• /
• 2012

Silicon carbide ceramics are used for oxidation resistive coating films due to their excellent properties like high strength, good oxidation resistance, and good abrasion resistance, but they have poor formability and are prepared by vapor process which is complicated, costly, and sometimes hazardous. In this study, preparation of silicon carbide coating film by liquid process using polymer precursor was attempted. Coating film was prepared by dip coating on substrate followed by heat treatment in argon at $1200^{\circ}C$. By changing the dipping speed, the thickness was controlled. The effects of plasticizer, binder, or fiber addition on suppression of crack generation in the polymer and ceramic films were examined. It was found that fiber additives was effective for suppressing crack generation.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.6
• /
• pp.1865-1872
• /
• 2011

This study investigates the sensitivity of a gas sensor to volatile organic compounds (VOCs) at various operating temperatures and catalysts. Nano-sized powdered $WO_3$ prepared by sol-gel and chemical precipitation methods was mixed with various metal oxides. Next, transition metals (Pt, Ru, Pd, and In) were doped on the surface of the mixture. Metal-$WO_3$ thick films were prepared using the screen-printing method. The physical and chemical properties of the films were studied by SEM/EDS, XRD, and BET techniques. The measured sensitivity to VOCs is defined as the ratio ($R_a/R_g$) of resistance ($R_{air}$) of $WO_3$ film in the air to resistance ($R_{gas}$) of $WO_3$ film in a VOCs test gas. The sensitivity and selectivity of the films were tested with various VOCs such as acetaldehyde, formaldehyde, methyl alcohol, and BTEX. The thick $WO_3$ film containing 1 wt % of Ru and 5 wt % of $SnO_2$ showed the best sensitivity and selectivity to acetaldehyde gas at an operating temperature of 300 $^{\circ}C$.

• Korean Journal of Metals and Materials
• /
• v.49 no.4
• /
• pp.313-320
• /
• 2011

100 nm-thick hydrogenated amorphous silicon $({\alpha}-Si:H)$ films were deposited on a glass and glass/30 nm Ni substrates by inductively-coupled plasma chemical vapor deposition (ICP-CVD) at temperatures ranging from 100 to $550^{\circ}C$. The sheet resistance, microstructure, phase transformation and surface roughness of the films were characterized using a four-point probe, AFM (atomic force microscope), TEM (transmission electron microscope), AES (Auger electron spectroscopy), HR-XRD(high resolution X-ray diffraction), and micro-Raman spectroscopy. A nano-thick NiSi phase was formed at substrate temperatures >$400^{\circ}C$. AFM confirmed that the surface roughness did not change as the substrate temperature increased, but it increased abruptly to 6.6 nm above $400^{\circ}C$ on the glass/30 nm Ni substrates. HR-XRD and micro-Raman spectroscopy showed that all the Si samples were amorphous on the glass substrates, whereas crystalline silicon appeared at $550^{\circ}C$ on the glass/30 nm Ni substrates. These results show that crystalline NiSi and Si can be prepared simultaneously on Ni-inserted substrates.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.264-264
• /
• 2007

$B_2Mg_{2/3}/Nb_{4/3}O_7\;(B_2MN)$ thin films and $Bi_{3/2}MgNb_{3/2}O_7\;(B_{1.5}MN)$ thin films were deposited as a function of various deposition temperatures on Pt/$TiO_2/SiO_2$/Si substrates by radio frequency magnetron sputtering system. Both of their thin films are shown to crystalline phase at $500^{\circ}C$, deposition temperature, using 100W RF power. The composition of them and structural micro properties are investigated by RBS spectrum and SEM, AFM. 200 nm-thick $B_2MN$ thin films were deposited at room temperature had capacitance density of $151nF/cm^2$ at 100kHz, dissipation factor of 0.003 and had capacitance density of $584nF/cm^2$ at 100kHz, dissipation factor of 0.0045 at $500^{\circ}C$ deposition temperature. Both of their dielectric constant deposited at room temperature and at $500^{\circ}C$ were each approximately 40 and 100.