• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.39-42
• /
• 2002

Recently, CMP (chemical mechanical polishing) technology has been widely used for global planarization of multi-level interconnection for ULSI applications. However, COO (cost of ownership) and COC (cost of consumables) were relatively increased because of expensive slurry. In this paper, we have studied the possibility of recycle of reused silica slurry in order to reduce the costs of CMP slurry. The post-CMP thickness and within-wafer non-uniformity(WIWNU) were measured as a function of different slurry composition. As a experimental result, the performance of reused slurry with annealed silica abrasive of 2 wt% contents was showed high removal rate and low non-uniformity. Therefore, we propose two-step CMP process as follows In the first-step CMP, we can polish the thick and rough film surface using remaked slurry, and then, in the second-step CMP, we can polish the thin film and fine pattern using original slurry. In summary, we can expect the saving of high costs of slurry.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.2
• /
• pp.126-130
• /
• 2011

In this study, off-axis magnetron sputtering was used for the crystallized ITO thin films at a low temperature of about $120^{\circ}C$ instead of the conventional RF sputtering because the off-axis sputtering can avoid the damage for the plasma as well as fabrication of thin films with a high quality. The ITO thin films grown on PET substrate at $120^{\circ}C$ were crystallized with a (222) preferred orientation. 58-nm thick ITO films showed a resistivity of about $2{\times}10-4{\Omega}{\cdot}cm$ and a transmittance of about 75% at a wavelength of 550 nm. The transmittance of the ITO thin films by an insertion of SiO2 thin films on ITO films was improved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.4
• /
• pp.238-243
• /
• 2018

A nanofiber was fabricated with carbon nanotubes for transparent electrodes. It was prepared with a composite solution of bio-molecules polycaprolactone (PCL) and multiwalled carbon nanotubes (MWCNTs) by electrospinning on a glass substrate, following which its electrical characteristics were investigated. The content of MWCNTs was varied during electrospinning, while that of PCL was fixed. Further, a nanometer-thick thin film of silver was deposited on the nanofiber layer using a thermal evaporator to improve the electrical characteristics; the sheet resistance significantly reduced after this deposition. The results showed that this carbon nanotube nanofiber has potential applications in biotechnology and as a flexible transparent display material.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.2
• /
• pp.47-50
• /
• 2010

This work discusses a two-step electroless plating method for preparing a Pt thin film on p-type InGaAs substrate, which is defined as Pt I and Pt II. A thin Pt catalytic layer formed in Pt I bath on the substrate at $65^{\circ}C$. In the following Pt II bath, thick Pt films then easily grew on the sensitized layer on InGaAs previously formed in the Pt I bath. The growth of Pt film is strongly influenced by the plating temperature and pH value. To study the plating time effect, the plating of Pt II bath is 5 to 40 min at $80^{\circ}C$ after using Pt I bath at 50~$65^{\circ}C$ for 5min of pH 8~13. Pt film for ohmic contact to p-type InGaAs was successfully prepared by using the two-step Pt electroless plating.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.338-338
• /
• 2007

Photo-conductive properties of CdS films deposited on glass substrates by a reactive sputtering in Ar atmosphere were characterized as a function of working pressure and the film thickness. The XRD measurements of CdS films revealed obvious (002) preferred orientation. In 300nm-thick of films, difference between dark and photo-resistance increases with increasing working pressure within the films. The films at 5 mTorr of working pressure show a dark resistance of approximately $1\;{\times}\;10^6\;{\Omega}/{\square}$ and a photo-resistance of $3\;{\times}\;10^4\;{\Omega}/{\square}$. The decrease dark- and photo-resistance of films as thickness decrease were $1.4\;{\times}\;10^6$ and $3\;{\times}\;10^4\;{\Omega}/{\square}$, respectively. CdS films deposited on glass substrates are considered tobe suitable for photo-conductivity materials in stealth radome applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.444-445
• /
• 2007

IZO/Al multilayer anode films for flexible top emitting organic light emitting diodes (TOLEDs) were grown on PEN (polyethylen-enaphthelate) substrate using twin target sputter (TTS) system. To investigate electrical and optical properties of IZO/Al multilayer films, 4-point probe method and UV/Vis spectrometer were used, respectively. From a IZO/Al multilayer films with 100nm-thick Al, sheet resistance of $1.4{\Omega}/{\square}$ and reflectance of above 62% at a range of 500~550nm wavelength could be obtained, In addition, structural and surface properties of IZO/Al multilayer films were analyzed by XRD (X-ray diffraction) and FESEM (field emission scanning electron microscopy) and AES (auger electron spectroscope), respectively. Moreover, flexibility of IZO/Al multilayer anode films were examined by bending test method.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.10
• /
• pp.1306-1311
• /
• 2020

In this study, we proposed an anti-reflective nano-structure to improve the photoresponsivity of AlGaN UV photodiode that can be used as a receiver in a solar blind UV optical communication system. The anti-reflective nano-structure was fabricated by forming Ni nano-clusters on SiO2 film followed by etching the underneath SiO2 film. A sample with the anti-reflective nano-structure exhibited lower surface reflection along with less dependency on the wavelength in comparison with a sample without the nano-structure. Finally, a UV photodiode was fabricated by applying an anti-reflective structure produced by heat-treating a 2 nm-thick Ni layer. The photodiode fabricated with the proposed nano-structure exhibited noticeable improvement in the photoresponsivity at the wavelength range from 240 nm to 270 nm in comparison with the same photodiode with a SiO2 film without the nano-structure.

• Journal of the Korean Ceramic Society
• /
• v.45 no.7
• /
• pp.411-417
• /
• 2008

Aerosol Deposition Method (ADM) is a novel technique to grow ceramic thick films with high density and nano-crystal structure at room temperature. $^{1,2)}$ For these unique advantages of ADM, it would be applied to the fabrication process of 3-D integration ceramic modules effectively. However, it is critical to control the properties of starting powders, because a film formation through ADM is achieved by impaction and consolidation of starting powders on the substrates. We fabricated alumina thick films by ADM for the application to integral substrates for RF modules. When the as-received alumina powders were used as a starting material without any treatments, it was observed that the dielectric properties of as-deposited alumina films, such as relative permittivity and loss tangent, showed high dependency on the frequency. In this study, some techniques of powder pre-treatments to improve the dielectric properties of alumina thick films will be shown and the effects of starting powders on the properties of AD films will be discussed.

• Journal of the Korean Ceramic Society
• /
• v.54 no.3
• /
• pp.243-248
• /
• 2017

Pd-doped $SnO_2$ thick film with a pure tetragonal phase was prepared on patterned Pt electrodes by an ink dropping method. Nanostructured $SnO_2$ powder with a diameter of 10 nm was obtained by a modified hydrazine method. Then the ink solution was fabricated by mixing water, glycerol, bicine and the Pd-doped $SnO_2$ powder. When the Pd doping concentration was increased, the grain size of the Pd-doped $SnO_2$ thick film became smaller. However, an agglomerated and extruded surface morphology was observed for the films with Pd addition over 4 wt%. The orthorhombic phase disappeared even at a low Pd doping concentration and a PdO peak was obtained for a high Pd doping concentration. The crack-free Pd-doped $SnO_2$ thick films were able to successfully fill the $30{\mu}m$ gap of the patterned Pt electrodes by the optimized ink dropping method. The prepared 3 wt% Pd-doped $SnO_2$ thick films showed monoxide gas responses ($R_{air}/R_{CO}$) of 4.0 and 35.6 for 100 and 5000 ppm, respectively.

• Advances in nano research
• /
• v.2 no.3
• /
• pp.173-177
• /
• 2014

This study is aimed to the numerical modeling of the surface plasmon-polariton excitation by a layer of active (electrically pumped) quantum dots embedded in a semiconductor, covered with a metal. It is shown that this excitation becomes much more efficient if the metal has a form of a thin (with thickness of several nanometers) film. The cause of this enhancement in comparison with a thick covering metal film is the partial surface plasmon-polariton localized at the metal-semiconductor interface penetration into air. In result the real part of the metal+air half-space effective dielectric function becomes closer (in absolute value) to the real part of the semiconductor dielectric function than in the case of a thick covering metal film. This leads to approaching the point of the surface plasmon-polariton resonance (where absolute values of these parts coincide) and, therefore, the enhancement of the surface plasmon-polariton excitation. The calculations were made for a particular example of InAs quantum dot layer embedded in GaAs matrix covered with an Au film. Its results indicate that for the 10 nm Au film the rate of this excitation becomes by 2.5 times, and for the 5 nm Au film - by 6-7 times larger than in the case of a thick (40 nm or more) Au film.