• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.12
• /
• pp.1253-1260
• /
• 1990

The traditional speed and pole position sensors, which are inevitable to drive the permanent magnet synchronous motors, are removed by the parameter identification using model reference adaptive systems. Also, the current detecting method is proposed on the synchronously rotating axis without the position information, and this enables the implementation of the proposed algorithm. The proposed methods have been confirmed both by digital simulation and experiments.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.32 no.3
• /
• pp.90-98
• /
• 1983

The method to improve the efficiency of a slightly loaded induction motor is suggested. It is based upon the optimal efficiency slip tracking by adjusting the voltage to frequency ratio(V/f). It is adopted the converter-inverter fed induction motor drive system. All the control loops are implemented bh the Z-80 microprocessor. By this method, 10% or more improvement is achieved at a few fraction of the full load.

• Tribology and Lubricants
• /
• v.17 no.1
• /
• pp.1-9
• /
• 2001

Hard disk drives operate in various environmental conditions. Thus, it is necessary to assess the reliability of the head/disk interface under these conditions. In this work, stiction and acoustic emission signals were investigated under different temperature, humidity, and ambient pressure conditions. Also, track average amplitude was observed for disk failure in N$_2$environment. It is shown that failure of the head/disk interface occurs more readily at high temperature and low ambient pressure conditions.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.04a
• /
• pp.277-283
• /
• 1991

일반적으로 건설중장비에 쓰이는 주행용 감속기의 종류에는 차동유성기구(Differential Planetary Drive), 2단유성기구(Two Stage Planetary Drive), 3단유성기구(Three Stage Planetary Dnive)가 있으나 전체적인 감속기의 성능 및 특성에 대해서는 자세히 알려져 있지않아 주행시스템의 국내개발이 미흡한 상황에 있다. 따라서 본 연구에서는 이러한 문제점의 1차적 해결책으로서 주행장치에 채용될 Heavy Duty용 유성기어 감속기를 차동유성기구 한개 모델과 2단유성기구 두개 모델을 시제품으로 제작하여 종류별로 동력전달효율과 감속기 내부 온도상승의 관점에서 그 성능을 비교 분석하여 각각의 특성을 제시하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.1
• /
• pp.58-69
• /
• 2016

This paper describes the design and implementation of a new diode clamped multilevel inverter for variable frequency drive. The diode clamp multilevel inverter has been widely used for low power, high voltage applications due to its superior performance. However, it has some limitations such as increased number of switching devices and complex PWM control. In this paper, a new topology is proposed. New topology requires only (N-1) switching devices and (N-3) clamping diodes compared to existing topology. A modified APO-PWM control method is used to generate gate pulses for inverter. The proposed inverter topology is coupled with single phase induction motor and its performance is tested by MATLAB simulation. Finally, a prototype model has built and its performance is tested with single phase variable frequency drive.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1410-1413
• /
• 2003

This paper presents the design technique for controlling the oscillation in the Disk Drive Read System via Derivative State Constrained (DSC)-Optimal $H_2$ Controller. The Optimal $H_2$, DSC-Optimal $H_2$ and Incorporating of Stability Degree Specification DSC Optimal $H_2$ are discussed. The results among these schemes are compared to verify the merit of DSC that effectively suppresses the oscillation in oscillatory system. The suggestions of how to select the weights of optimal controls are given.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.3
• /
• pp.273-280
• /
• 1990

To prevent the shoot-through phenomena in a PWM inverter, a short dead time is usually provided between a pair of switching transistors in the same leg of the inverter. In this approach, the amount of the dead time is designed to meet the worst case condition of the inverter transistors and the base drive elements. So, in normal cases, relatively large portion of the dead time is unnecessary and it results in an undesirablecurrent waveform distortion and generates ripple torque on the motor shaft. In this paper, a new base drive method to remove the undesirable portion of the dead time is described. The method senses the transistor on/off states to interlock the other transistor of the leg without the external dead time. Also, for the transistors of large current rating, the Darlington drive circuit is combined to the proposed method and is tested to verify the effectiveness. The experimental results of the proposed method are described and compared with those of the conventional dead time method.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.4
• /
• pp.161-161
• /
• 2003

The applications of SRM(Switched Reluctance motor) are dramatically increasing due to a simple mechanical structure, a high efficiency and a high speed drive characteristics. Energy recovery in the regenerative region is very important when SRM is used in traction drive. This is to reduce energy loss during mechanical braking and/or to have a high efficiency drive. To control excitation voltage during motoring and regenerating voltage in the generator operation in the SRM, multi-level voltage control is effective. This paper suggests multi-level inverter which is useful for motoring and regenerative operation. The proposed method is verified through simulations and experiments.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.6
• /
• pp.588-599
• /
• 1992

This paper describes the variable speed drive of an induction motor by the line commutated inverter, which is operated in the forced commutation mode from start-up to operating point of load commutation. A novel forced-commutation circuit is proposed in this paper. The selection range of leading condenser to decide load commutation starting point is simulated by the sampling data of a general purpose IM and a high speed IM. The experiment to drive IM by a line commutated inverter with the proposed forced commutated circuits is performed. There was no problem in driving IM from standstill to starting point of load commutation by a line commutated inverter with forced commutation.

• International Journal of Automotive Technology
• /
• v.8 no.5
• /
• pp.593-598
• /
• 2007

A new continuously variable transmission for bicycles(B-CVT) is developed by using a traction drive mechanism having inner and outer spherical rotors. The B-CVT has high power efficiency, large torque capacity, improved drivability and good packageability. The ratio change mechanism for the B-CVT is very simple, in contrast with other traction drive CVTs. After completing a conceptual design, a performance analysis and a detail design, a prototype of the B-CVT has been manufactured. The prototype has rated power of 100 watts, pedal speed of 6 rad/s and an overall speed ratio of 1.0-4.0. A bench test and an actual bicycle test have been performed to verify the practicability of the B-CVT.