• 전력전자학회논문지
• /
• 제4권5호
• /
• pp.413-422
• /
• 1999

Auto-connected multipulse(12/24pulse) rectifier schemes are cost effective methods for reducing line current hamonics in PWM drive systems. Employing these schemes to enhance utility power quality requires careful attention to several design considerations In particular, excursion of dc-link voltage at no load, effect of pre-existing voltage distortion, impedance mismatches, unequal diode drops on rectifier current sharing and performance, are fully analyzed, Several corrective measures to improve the performance of 12/24­pulse rectifier systems are also discussed. Finally, experimental results on a 460V, 60Hz 400kVA commercial ASD, retrofitted with 12/24pulse rectifier systems are discussed in detail.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.616-618
• /
• 1996

This paper presents an unipolar PWM which commutated switching device only in a half period. This method reduced switching loss significantly because of decreasing switching number in n period. In high speed motor drive needed high frequency above 300 Hz fundamental frequency, this method is suited very well. This paper described the principle of unipolar PWM method, analyzed harmonic spectrum and compared with bipolar PWM, Modified PWM and Overmodulation method in switching loss.

• 대한기계학회논문집B
• /
• 제27권1호
• /
• pp.17-24
• /
• 2003

A mathematical model of the hydrodynamic and heat transfer performances of two-phase flow (gas-liquid) in thin film region of micro channel is proposed. For the formulation of modeling, the flow of the vapor phase and the shear stress at the liquid-vapor interface are considered. In this work, disjoining pressure and capillary force which drive the liquid flow at the liquid-vapor interface in thin film region are adopted also. Using the model, the effects of the variations of channel height and heat flux on the flow and heat transfer characteristics are investigated. Results show that the influence of variation of vapor pressure on the liquid film flow is not negligible. The heat flux in thin-film region is the most important operation factor of micro cooler system.

• 한국정보과학회:학술대회논문집
• /
• 한국정보과학회 2011년도 한국컴퓨터종합학술대회논문집 Vol.38 No.1(B)
• /
• pp.438-441
• /
• 2011

최근 태블릿 컴퓨터(Tablet computer) 등 첨단 모바일 기기가 대중화되고 고성능 노트북이 널리 사용되면서 SSD(Solid State Drive)를 주 저장장치로 사용하는 시스템이 증가하고 있다. 이들 시스템에서는 SSD를 가상메모리의 스왑 영역으로 사용하므로 이에 적합한 가상메모리 정책이 필요하다. SSD 제조사는 SSD 내부의 자세한 정보는 제공하지 않기 때문에 최적화된 할당에 어려움이 생긴다. 본 논문에서는 SSD의 내부 상태를 기록하고, VM의 스왑 공간으로 사용 시 각블록 상태를 고려하여 최적화된 할당 페이지를 선택하는 기법을 제안한다.

• KSTLE International Journal
• /
• 제3권2호
• /
• pp.114-118
• /
• 2002

In this work, head-disk interactions are studied when flying height becomes lower than laser bump height on the landing zone of a disk. With the reduction of the spinning speed in a spin stand, the flying height is decreased under the height of laser bumps. Conventional and padded pico sliders sweep between landing Bone and data zone and, then, the dynamic behavior of the pico sliders and head-disk impacts are investigated using AE and stiction/friction signals. After 200n cycle-sweep tests, bearing analysis and AFM analysis indicate that there are some signs of wear and plastic deformation in the landing zone of a disk, although AE and stiction/friction signals are not significantly changed during the sweep tests. The experimental results of this paper suggest that in CSS tests at component level, more rigorous examination methods of wear and plastic deformation might be necessary as flying height becomes getting lower.

• 한국농공학회지
• /
• 제39권2호
• /
• pp.51-56
• /
• 1997

Abstract Over 4.1 billion tons of non-hazardous solid wastes are generated in the United States annually. This equals to about 16 tons of wastes per person, per year. Disposal of the wastes is a national concern due to many factors such as environmental issues, costs, and public views. South Carolina, like many other states, had a home of many military bases which were ordered to be closed. The contaminated soil was vitrified and tested for suitability in the asphalt mixes. For mix design purposes, a total of 75 specimens were made and tested. For moisture susceptibility testing, a total of 32 samples were made and tested. The results indicate that the mixtures made with sample B produced dry and wet that were comparable with the controlled mixture. At this point and with in this limited study, use of 5% of sample B in asphalt mixture is recommended in several applications such as parking lots, walking paths and drive ways.

• 전기학회논문지
• /
• 제59권3호
• /
• pp.562-568
• /
• 2010

In this paper, a low cost magnetic position sensor for linear position detection is proposed. The proposed magnetic sensor can be applied to the linear motor which has stator with periodical teeth, such as transverse flux linear motor(TFLM). Sine and cosine waves can be generated from the unit sensor module as the linear motor moves, and the outputs can be converted to the position data by interpolation IC. To reduce the speed ripple caused by the position error, the Luenberg observer is introduced. The validity of the proposed magnetic position sensor is verified by experiment with a 750N three-phase TFLM.

• Journal of the Korean Statistical Society
• /
• 제34권3호
• /
• pp.219-233
• /
• 2005

The 3-way balanced multi-level rotation design has been discussed (Park Kim and Kim, 2003), where the 3-way balancing is done on interview time, in monthly sample and rotation group and recall time. A greater advantage of 3-way balanced design is accomplished by an estimator. To obtain the advantage, we generalized previous generalized composite estimator (GCE). We call this as l-step GCE. The variance of the l-step GCE's of various characteristics of interest are presented. Also, we provide the coefficients which minimize the variance of the l-step GCE. Minimizing a weighted sum of variances of all concerned estimators of interest, we drive one set of the compromise coefficient of l-step GCE's to preserve additivity of estimates.

• Journal of Biosystems Engineering
• /
• 제35권5호
• /
• pp.287-293
• /
• 2010

In order to optimize an agricultural tractor clutch mechanism system, its structural static and kinematic mechanism were analyzed. The operating force of the mechanical tractor clutch system is currently not appropriate to drive comfortably. So it is needed to reduce the clutch operating force by applying advanced engineering design techniques. In the present study, an optimization technology is applied to the design of tractor clutch systems to reduce the operating force. As a result of the optimization using 2 link-angles and 1 link-length which are the main design variables of the clutch linkage system, the maximum pushing force of the maximum clutch pedal was found 182.8N, 14% decreased compared to the existing clutch system. The effectiveness of the optimum design is certified by menas of an experiment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 학술대회 논문집 전문대학교육위원
• /
• pp.128-130
• /
• 2007

외과수술용 핸드피스는 현재 국내 외 병원에서 사용되고 있는 수술 장비 중 필수 보유 장비이다. 선진 수술 기법인 인공관절 대체 수술 시 뼈(Bone)절단, 다듬질 구멍 등, 초 섬세 가공을 목적으로 하는 기기이다. 기존의 공압식(Air Type)은 수술 시 많은 양의 질소(N2 Gas)가 소모됨으로써 질소탱크 보관에 많은 공간이 필요하고 잦은 교체를 필요로 한다. 또한 기계소음과 공압식 호스의 이동으로 시술자와 환자사이에 불편함이 발생하고 감염의 위험성이 있으므로 최근에는 충전식을 선호하고 있다. 이러한 이유로 기존의 공압식을 대체할 배터리형 외과수술용 핸드피스를 연구하게 되었다.