• Transactions on Electrical and Electronic Materials
• /
• v.15 no.2
• /
• pp.81-86
• /
• 2014

The process parameter in optimized KOH alkali activation of soft carbon series coke material in high purity was set with DOE experiments design. The activated carbon was produced by performing the activation process based on the set process parameters. The specific surface area was measured and pore size was analyzed by $N_2$ absorption method for the produced activated carbon. The surface functional group was analyzed by Boehm method and metal impurities were analyzed by XRF method. The specific surface area was increased over 2,000 $m^2/g$ as the mixing ratio of activation agent increased. The micro pores in $5{\sim}15{\AA}$ and surface functional group under 0.4 meq/g were obtained. The contents of the metal impurity in activated carbon which is the factor for reducing the electrochemical characteristics was reduced less than 100 ppm through the cleansing process optimization. The electrochemical characteristics of activated carbon in 38.5 F/g and 26.6 F/cc were checked through the impedance measuring with cyclic voltammetry scan rate in 50~300 mV/s and frequency in 10 mHz ~100 kHz. The activated carbon was made in the optimized activation process conditions of activation time in 40 minutes, mixing ratio of activation agent in 4.5 : 1.0 and heat treatment temperature over $650^{\circ}C$.

• Journal of Environmental Science International
• /
• v.10 no.5
• /
• pp.373-380
• /
• 2001

In recent years, the demand of activated carbon has been increasing steadily because of the environmental problems. Among them waste and water treatment and removal of poisonous gas were invorved. Therefore, in this study, activated carbon was made from the waste chinese cabbage and measured the iodine adsorption ability, carbonization yield, and activation yield of the produced activated carbon. The result showed that the carbonization yield was decreased when carbonization temperature was increaed and that the optimal carbonization temperature was $600{\circ}C$. The optimal concentration of NaOH for removing ash in the raw sample was 1~2N. The range of iodine adsorption number of activated carbon using chinese cabbage at $600{\circ}C$. carbonization was 610.82mg/g to 1019.58mg/g. The activation result of carbonization sample showed that the optimal activation condition was the carbonization at $400\circ}C$ and the activation at$700{\circ}C$. So the production of activated carbon using chinese cabbage was possible in the aspect of reuse of resource and decrease of environmental pollution compared to the commercial activated carbon.

• Analytical Science and Technology
• /
• v.18 no.5
• /
• pp.436-443
• /
• 2005

A study of physical properties and their application using K-powdered activated carbon system followed powdered carbon dispersion was carried out at laboratory. scale. Two types of K-powdered activated carbon for the dispersion have been used in this study to investigate the catalytic removal efficiency of pollutants from the wastewater. From the surface properties obtained for carbon samples treated with aqueous solutions containing potassium salts, main investigations were subjected to isotherm shape, SEM, EDX and surface functional groups. K-powdered activated carbons were dispersed to wastewater with pH variation to investigate the removal efficiency for the color, COD, T-N and T-P. From these removal results of the piggery waste using K-powdered activated carbon, satisfactory removal performance in the region of pH 6~8 was achieved. The excellent effects for the dispersion of the K-powdered activated carbon were proved by the above mentioned properties of the material for adsorption and trapping of organics, and catalytic effects.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.7
• /
• pp.1319-1330
• /
• 2000

Activated carbons prepared by chemical activation of organic waste sludges with $ZnCl_2$ and $K_2S$ have been studied in terms of their pore development and adsorptivity. Pore development of the carbons prepared from organic waste sludges was characterized by the nitrogen adsorption at 77K. The $ZnCl_2$-activated carbon produced by chemical activation with zinc chloride exhibited type I isotherm characteristics according to the BDDT classification, suggesting the presence of micropores formed by activation process. The isotherms of the commercial powdered activated carbon and $K_2S$-activated carbon reveal a hysteresis similar to that of type IV in BDDT classification, indicating the formation of mesopores. This result implies that the major pores of $K_2S$-activated carbon are composed of meso and micropores, and a macropores are minor. The adsorptive capacities of metal on the $K_2S$-activated carbon prepared from organic waste sludges were found to be superior to those on a commercial granular activated carbon. The Langmuir and Freundlich isotherms yield a fairly good fit to the adsorption data, indicating a monolayer adsorption of metals onto $K_2S$-activated carbon. The adsorptive capacity of the $K_2S$-activated carbon was superior to $ZnCl_2$-activated carbon for $PO_4$-P, and vice versa for $NO_3$-N. From the results of the studies reported here, it can be concluded that activated carbons with adsorptivity superior to commercial granular activated carbons can be produced from organic waste sludge using a two-step carbonization/activation procedure with zinc chloride or potassium sulfide as the activating agents.

• Membrane Journal
• /
• v.24 no.1
• /
• pp.20-30
• /
• 2014

A membrane-coupled sequencing batch reactor (MSBR) was used for the advanced treatment of rural village sewage which is very low C/N ratio. The effect of powdered activated carbon, aeration rate, and external organic material loadings on the treatment efficiency and filtration performance were investigated in sequencing batch reactor, in which a flat-sheet type microfiltration membrane with a pore size of $0.4{\mu}m$ was submerged. At the initial operation (within 54 days) MLSS concentration, and the removal efficiencies of COD, T-N, and T-P were increased with the increase of C/N ratio. After 89 days the removal efficiencies of COD, T-N, and T-P were 97.1%, 75.0%, and 48.3%, respectively. Suspended solid-free effluent was obtained by membrane filtration. The T-P removal was relatively low because of depending on the amount of excess sludge wasting. During the operation of MSBR with powdered activated carbon, the particle size of the sludge reduced by the increase of collision frequency and mixing intensity. In comparison with MSBR without powdered activated carbon, TMP of MSBR with that was significantly elevated.

• Journal of Korean Society on Water Environment
• /
• v.22 no.6
• /
• pp.996-1003
• /
• 2006

The absorption characteristics of powdered activated carbon doped by transition-metal nanoparticles were investigated to enhance the remove efficiencies of $TCOD_{Mn}$ and Color from the flexo-inks wastewater. According to the adsorption dynamics of PAC and MPAC, the optimal dosage of activated-carbon adsorbents was 3 g/L under the reaction conditions of pH6.0, 30 mill of reaction time, 240 rpm of mixing intensity. The removal efficiencies by the optimal dosages were maximized as 19% $TCOD_{Mn}$, 57% Color for PAC and 88% $TCOD_{Mn}$, 95% Color for MPAC. Freundlich indexes of isotherm absorption were estimated as follows: i) For PAC, k=-8.11, 1/n=2.98, r=0.91 in the raw water, and k=0.14, b/n=0.75, r=0.96 in the biological treatment water, ii) For MPAC, k=2.69, 1/n=0.21, r=0.80 in the raw water, and k=0.74, 1/n=1.17, r=0.95 in the biological treatment water. MPAC (Powdered activated carbon doped by transition-metal nanoaprticles) was very effective in the removal of organics from the raw water and biological treatment water, as Freundlich indexes of 1/n for both types of water were estimated less than 2.0.

• Journal of the Korean Society of Tobacco Science
• /
• v.27 no.2
• /
• pp.171-177
• /
• 2005

Coconut based activated carbon and silica-gels were impregnated with 3-aminopropyltri ethoxysilan(APS) and N-(2-aminoethyl)-3-aminopropyl triethoxysilane (AEAPS) in order to investigate the effect of the amine group and the pore size of the supports on the removal of hydrogen cyanide(HCN) and aldehydes in mainstream smoke(MS). The physicochemical properties of the supports were analyzed by using thermal gravity analyzer(TGA), $N_2$ adsorption and desorption isotherms$(BET,\;N_2)$, and SEM-EDS. According to our experimental data, there was no significant difference in the delivery amount of HCN and aldehydes of non-functionalized silica-gels having meso-pores bigger than $20\AA$. In the case of silica-gels functionalized with APS(APS silica-gel), the delivery amounts of hydrogen cyanide(HCN) and aldehydes decreased with the increase of APS concentration. Silica-gel functionalized with AEAPS(AEAPS silica-gel) showed higher removal efficiency than that of APS silica-gels. The delivery amounts of HCN and aldehydes of activated carbon impregnated with APS and AEAPS increased with the increase of the APS and AEAPS concentrations. In accordance with the specific surface area analysis results, APS and AEAPS molecules decreased the specific surface area by blocking the micro-pores of the activated carbon. The volatile organic components removal efficiency by the micro-pores was higher than that of the amine group impregnated into the activated carbon.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.06a
• /
• pp.67-71
• /
• 1997

Activated carbons are the microporous carbonaceous adsorbents which are prepared from carbon-containing source materials such as wood, coal, lignite, peteroleum and sometimes synthetic high polymers. [1-2] Activated carbons shows an ability to adsorbe hydrocarbons of the gas phase. Activated carbons are used in the purification of many kinds of gas phases like hexane, benzene, toluene, gasoline, phenol etc.[3] In this study, cokes from bitminous coal were activated for the purpose of preparing the activated carbons by steam activation. The effect of the activation temperature, time, steam concentration and flow rate on the n-butane adsorption, burn off, surface area and average pore size of the activated carbons, were investigated. The adsorption characteristics of the activated carbons for gasoline are indirectly estimated by n-butane adsorption.

• Journal of Environmental Health Sciences
• /
• v.27 no.1
• /
• pp.63-68
• /
• 2001

A laboratory experiment was performed to invstigate the nitrate removal using FeCl$_3$ -treated activated carbon. Iron chloride(III) was coated onto the surface of activated carbon. The removal efficiency of nitrate was increased with increasing of FeCl$_3$ was used for coating material. About 22~26mg of Fe per unit g of activated carbon was adsorbed. The nitrate removal was not affected by the pH under the experiment range of pH, but the pH value in solution decrease to 3.5~4.0 after reaction. The removal efficiency of nitrate was increased with increasing of dosage of adsorbents. Ammonia was not detected and the Fe concentration as low as 0.22mg/$\ell$ was desorbed from the adsorbents. The adsorbents was regenerated using KCl solution, and recovery was 76.6% at 1 M of KCl. The adsorption of nitrate by FeCl$_3$-treated activated carbon followed the Freundlich isotherm equation and the Freundlich constant, 1/n, was 0.346. These results showed that the FeCl$_3$-treated activated carbon could serve as the basis of a useful nitrate removal.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.5
• /
• pp.879-886
• /
• 2000

$H_2S$ adsorption characteristics of activated carbon adsorbent impregnated with NaOH were investigated. The concentrations of NaOH reagent were 1~8N and the particle size of activated carbon was $8{\times}30$ mesh. The experimental results showed that the BET surface area decreases from $1050m^2/g$ to $783m^2/g$ and acidity of activated carbon decreases from 0.541 meq/g-AC to 0 meq/g-AC, while pH increases from 9.56 to 10.86 when the impregnation ratio increases from 0.87% to 5.8%. It was also found that the $H_2S$ adsorption equilibrium capacity of activated carbon impregnated with NaOH increases with increasing temperature and $H_2S$ concentration and varies in the range of 17.87~30.34 mg/g-AC at adsorption temperature of $45^{\circ}C$, which is 2~3 times larger than that of pure activated carbon.