• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.1001-1003
• /
• 1998

In this paper, $Ar^+$ ion laser etching process of single/poly crystalline silicon with $CCl_{2}F_{2}$ gas is studied for MEMS applications. To investigate the effects of process parameters, laser power, gas pressure, scanning speed were varied and multiple scanning was carried out to obtain high aspect ratio. In addition, scanning width was varied to observe the trench profile etched in repeating scanning cycle. From the etching of $2.6{\mu}m$ thick polycrystalline Si deposited on insulator, trench with flat bottom and vertical side wall was obtained and it is possible to apply this results for MEMS applications.

• Journal of the Korean Society of Visualization
• /
• v.3 no.1
• /
• pp.63-70
• /
• 2005

Optical Line Patternator(OLP) has been applied to get a distribution of the spray at high ambient pressure. OLP is a combined technique of extinction measurement and image processing. The attenuated intensity of laser beam after traversing spray region was measured by using a photo-detector, and the line image of Mie-scattering was captured simultaneously in the path of each laser beam by using a CCD camera. The distribution of extinction coefficient in the spray is obtained by processing these data with the algebraic reconstruction technique. From the distribution of extinction coefficient, the surface distribution of spray can be reconstructed. OLP does not use laser sheet but use laser beam so that the noise effect of multiple scattering, caused by increasing number density of droplet in high pressure environment, is reduced drastically. OLP is expected as a suitable method which can investigate the characteristics of relatively large spray under the high pressure environment such as liquid rocket engine.

• Journal of Communications and Networks
• /
• v.10 no.1
• /
• pp.1-4
• /
• 2008

This paper reports the design of a multiwavelength fiber laser source that utilizes a linear cavity of hybrid Brillouin/Erbium fiber laser (BEFL). The output power, threshold power and free running cavity modes were investigated against the pump powers. The structure exhibited low threshold operation of 4 mW at 2.3 mW injected Brillouin pump power. The optimization of Brillouin pump wavelength, power and Erbium gain led to a maximum possible number of channels generated. Simultaneous and stable operation of 21 channels with 10.88 GHz channels spacing were obtained from this architecture at 1 mW injected Brillouin pump power and 90 m W Erbium doped fiber pump power in the 1555 nm region.

• Restorative Dentistry and Endodontics
• /
• v.29 no.5
• /
• pp.423-429
• /
• 2004

The purpose of this study was to evaluate the effect of multiple application of all-in-one dentin adhesive system on microtensile bond strength using confocal laser scanning microscope and microtensile bond strength test. Flat occlusal dentin surfaces were prepared using low-speed diamond saw. In group I, Scotchbond Multipurpose (SM) was applied by manufacturer's recommendation. In group II, after Adper Prompt L-Pop was applied for 15s and light cured for 10s. the second coat was re-applied and light-cured. In group III, after light-curing the second layer. the third coat was re-applied and light-cured. Specimens bonded with a resin-composite were sectioned into resin-dentin stick for measuring the adhesive layer thickness by confocal laser scanning microscope and evaluating micro-tensile bond strength. The adhesive layers of three-step dentin adhesive system. 3 coats of Adper Prompt L-Pop had significantly thicker than SM. 2 coats of Adper Prompt L-Pop (p < 0.05). However. there was no significant differences in bond strengths between SM and 3 coats of Adper Prompt L-Pop (p > 0.05). And SM. 3 coats of Adper Prompt L-Pop had significantly higher than 2 coats of Adper Prompt L-Pop in bond strengths (p < 0.05).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.33-42
• /
• 2013

This paper describes a multiple vehicle tracking algorithm using an integrated probabilistic data association filter (IPDAF) in urban environments. The algorithm consists of two parts; a pre-processing stage and an IPDA tracker. In the pre-processing stage, measurements are generated by a feature extraction method that manipulates raw data into predefined geometric features of vehicles as lines and boxes. After that, the measurements are divided into two different objects, dynamic and static objects, by using information of ego-vehicle motion. The IPDA tracker estimates not only states of tracks but also existence probability recursively. The existence probability greatly assists reliable initiation and termination of track in cluttered environment. The algorithm was validated by using experimental data which is collected in urban environment by using single laser scanner.

• Current Optics and Photonics
• /
• v.2 no.1
• /
• pp.27-33
• /
• 2018

We report the physical implementation of a tunable photonic microwave delay line filter based on injection locking of a single Fabry-Perot laser diode (FP-LD) to a reflective semiconductor optical amplifier (RSOA). The laser generates equally spaced multiple wavelengths and a single tapped-delay line can be obtained with a dispersive single mode fiber. The filter frequency response depends on the wavelength spacing and can be tuned by the temperature of the FP-LD varying lasing wavelength. For amplitude control of the wavelengths, we use gain saturation of the RSOA and the offset between the peak wavelengths of the FP-LD and the RSOA to decrease the amplitude difference in the wavelengths. From the temperature change of total $15^{\circ}C$, the filter, consisting of four flat wavelengths and two wavelengths with slightly lower amplitudes on both sides, has shown tunability of about 390 MHz.

• Journal of Welding and Joining
• /
• v.23 no.2
• /
• pp.81-89
• /
• 2005

A numerical model for multiple reflection effects of a polarized beam on laser grooving has been developed. The surface of the treated material is assumed to reflect laser irradiation in a fully specular fashion. Combining electromagnetic wave theory with Fresnel's relation, the reflective behavior of a groove surface can be obtained as well as the change of the polarization status in the reflected wave field. The material surface is divided into a number of rectangular patches using a bicubic surface representation method. The net radiative flux far these patch elements is obtained by standard ray tracing methods. The changing state of polarization of the electric field after reflection was included in the ray tracing method. The resulting radiative flux is combined with a set of three-dimensional conduction equations governing conduction losses into the medium, and the resulting groove shape and depth are found through iterative procedures. It is observed that reflections of a polarized beam play an important role not only in increasing the material removal rate but also in forming different final groove shapes. Comparison with available experimental results for silicon nitride shows good agreement for the qualitative trends of the dependence of groove shapes on the electric field vector orientation.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.11
• /
• pp.7-16
• /
• 2010

In this study, wire was used as the filler material for the laser repair welding, and the phenomenon in which the supplied filler material was melted and beaded down into the specimen was examined with varying laser powers and welding speeds. The optimal processing condition was found to be the laser power of 1,300 W, the welding speed and feed wire supply speed of 0.5 ml/in and the defocused distances of +2mm. At this time, the heat input(E) was $65{\sim}75\;J/mm^2$, and no internal defect occurred. When repair welding was carried out as the optimal processing for the part that had an external defect with the radius of 2mm, the filler metal was melted, resulting in the volume smaller than the defect part and thus causing the part unfilled. Therefore, it was found to be necessary to carry out repair welding two to three times by multiple passes rather than does it only once by single pass.

• Journal of Korean society of Dental Hygiene
• /
• v.12 no.4
• /
• pp.655-663
• /
• 2012

Objectives : This study was progressed a research with the aim of using it as basic data necessary for a plan in order to increase qualitatively medical level for patients who feel anxiety about dental treatment, and of offering basic data for improving the whole medical services by grasping conditions and satisfaction level with laser therapy in patients who visited dental clinic. Methods : The statistical analysis was carried out t-test and ANOVA by using SPSS(PASW statistics) 18.0. When there is statistically significant difference in analysis of variance, post-test was carried out by using Duncan multiple range test. Results : In therapy kinds of using laser, gingival treatment was the largest with 37.0%. It was the highest in likely seeming to be not painful with 32.9% as for a decisive factor, which came to receive laser therapy, and in having been enough to endure even if having been slightly tingling as for pain level. Conclusions : This study can be considered to have significance in changing recognition of medical cure by surveying patients satisfaction with using laser as a method for slightly solving elements of fear and anxiety about dental treatment and to have its value as basic data for seeking improvement plan for diverse medical services in the future.

• Korean Journal of Construction Engineering and Management
• /
• v.25 no.3
• /
• pp.68-82
• /
• 2024

The planning stage of laser scanning is crucial for acquiring high-quality 3D source data. It involves assessing the target space's environment and formulating an effective measurement strategy. However, existing practices often overlook on-site conditions, with decisions on scanner deployment and scanning locations relying heavily on the operators' experience. This approach has resulted in frequent modifications to scanning locations and diminished 3D data quality. Previous research has explored the selection of optimal scanner locations and conducted preliminary reviews through simulation, but these methods have significant drawbacks. They fail to consider scanner inaccuracies, do not support the use of multiple scanners, rely on less accurate 2D drawings, and require specialized knowledge in 3D modeling and programming. This study introduces an optimization technique for laser scanning planning using 3D simulation to address these issues. By evaluating the accuracy of scan data from various laser scanners and their positioning for scanning a retaining wall structure in a small-scale building, this method aids in refining the laser scanning plan. It enhances the decision-making process for end-users by ensuring data quality and reducing the need for plan adjustments during the planning phase.