• Transactions on Electrical and Electronic Materials
• /
• 제10권1호
• /
• pp.5-8
• /
• 2009

The reliability of multilayer ceramic capacitor with active thin dielectric layer was investigated by highly accelerated life test at various stress condition. The distribution of multilayer ceramic capacitor failure times is plotted as a function of time from Weibull distribution function. According to the test result, voltage acceleration factor is obtained from 2.24 to 2.96. The acceleration by temperature is much higher than other values of active thick dielectric layer. It is clear that median time to failure is affected by the stress voltage for high volumetric efficiency ceramic capacitors with active thin dielectric layer. The degradation under stress of voltage involves electromigration and accumulation of oxygen vacancy at Ni electrode interface of cathode.

• 한국세라믹학회지
• /
• 제24권3호
• /
• pp.207-214
• /
• 1987

This paper is to determine the effect of binder burnout time and heating rate on the electrical propertries of type II multilayer ceramic capacitors(MLC). The quality of multilayer ceramic capacitor depends suitable on the binder burnout time, which is determined for at least 24 hours in the PVB-binder system. It is suggested that theelectrical properties of multilayer ceramic capacitor is due to the control of heating rate, with the dipole moment density from grain size distributiion. Comparing the fast firing with slow, we observed a small but consistent improvement in the electrical properties.

• Journal of Electrical Engineering and Technology
• /
• 제8권4호
• /
• pp.808-812
• /
• 2013

Multilayer capacitors with high ripple current and high capacitance were manufactured. The electrical properties of these capacitors were characterized for potential application for DC-link capacitors in hybrid electric vehicle inverters. Internal electrode structures were designed to achieve high capacitance and reliability. A single multilayer capacitor showed $0.46{\mu}F/cm^3$ of capacitance, 0.65% of dielectric loss, and 1450 V to 1650 V of dielectric breakdown voltage depending on the design of the internal electrode. The capacitor module designed with several multilayer capacitors gave a total capacitance of $450{\mu}F$, which is enough for hybrid electric vehicles. In particular, an equivalent series resistance of $4.5m{\Omega}$ or less will result in 60 $A_{rms}$, thereby reaching the allowed ripple current for hybrid electric vehicles.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.72-74
• /
• 2014

Multilayer ceramic capacitor (MLCC) makes acoustic noise of electronic devices. Conversed piezoelectric effect of dielectric substance consists of $BaTiO_3$ causes vibration of MLCC so it must be analyzed to reduce the noise. Thus, finite element model for piezoelectric analysis of MLCC was constructed in this paper. Piezoelectric characteristics of MLCC was considered for the accurate simulation result. Displacement response for sinusoidal voltage signal was measured and simulation result was verified with test result.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2005년도 춘계학술대회 논문집
• /
• pp.35-39
• /
• 2005

This paper presents a method to reduce hysteresis in multilayer ceramic actuator by connecting the actuator with a capacitor in a series circuit. The change in hysteresis with respect to the capacitor was examined. $0.2Pb(Mg_{1/3}Nb_{2/3})O_3-0.8Pb(Zr_{0.475}Ti_{0.525})O_3$ ceramic material was used as a piezoelectric material for the actuator. Displacement of the actuator was measured in a capacitive gap sensor measuring system. In case of inserting a capacitor in a total circuit, hysteresis became dramatically decreased, and then finally the hysteresis value can be reduced below $0.2\%$. It was found in this present study that reducing the hysteresis in the actuator is dependent upon the characteristics of the capacitor in total circuit and also operating frequency.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.75-78
• /
• 2002

The dielectric properties for Ni electrode multilayer ceramic chip capacitor for Y5V has been studied with $(Ba_{0.93}Ca_{0.07})_m(Ti_{0.82}Zr_{0.18})O_2+MnO_2$ 0.2wt%, $Y_2O_3$ 0.18wt%, $SiO_2$ 0.15wt%, glass frit 1 wt% composition. The m ratio in the range of 1.006 ~ 1.012 have dielectric constant 9,500 ~ 14,500 and insulation resistance 390 ~ 460 $G{\Omega}$. Using the dielectrics, nikel electrode multilayer chip capacitor with Y5V, 104Z in EIA 0603 size specific capacitance were developed.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2000년도 춘계총회,특별강연,심포지움,연구발표회
• /
• pp.27.1-27.1
• /
• 2000

• 한국세라믹학회지
• /
• 제40권11호
• /
• pp.1090-1095
• /
• 2003

본 논문에서는 고품질 적층형 수동 소자의 모델링 및 설계에 관하여 연구하였고, 설계된 수동 소자를 이용하여 안테나 스위치 모듈 내에 포함된 이중 대역 GSM/DCS 대역 분리용 적층형 다이플렉서를 설계$.$제작하여 그 특성을 고찰하였다. 적층형 수동 소자는 시스템의 소형화를 위해 인덕터는 정방형 스파이럴 구조로, 캐패시터는 입체적인 인터디지털 형태인 VIC 구조로 설계하였다. GSM 저역 통과 필터는 0.55 dB 이하의 삽입 손실과 12dB 이상의 반사 손실을 나타내며, 통과 대역 위쪽 저지 대역인 1800 MHz 부근에 감쇠극이 존재하도록 설계함으로써 DCS 통과 대역에서 26 dB 이상의 저지 특성을 나타내었다. DCS 고역 통과 필터는 0.82 dB 이하의 삽입 손실과 11 dB 이상의 반사손실을 가지며, 통과 대역 아래 쪽 저지 대역인 930 MHz 부근에 감쇠극이 존재하도록 설계함으로써 GSM 통과 대역에서 38 dB 이상의 저지 특성을 나타내었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.392-393
• /
• 2014

Multilayer ceramic capacitors (MLCCs) have become one kind of the most widely used electrical components in recent decades. And the technology of MLCCs is developing continuously towards a direction of high capacitance and miniaturization. While the tiny thickness and the large quantity of the layers often make it very troublesome to do analysis with the full model MLCCs. In order to solve this problem, reduced model with fewer layers of MLCC was designed and verified in this paper.

• Transactions on Electrical and Electronic Materials
• /
• 제13권4호
• /
• pp.181-184
• /
• 2012

$BaTiO_3$ based multilayer ceramic capacitors with Ni electrodes can be explained as 2-2 composites with different thermal expansion coefficient and sintering behaviors. To achieve the high capacitance and reliability of MLCCs, a homogenous Ni electrode configuration with high connectivity is required. We controlled the heating rates during sintering to achieve densification by suppressing grain growth. Experimental results revealed that a large heating rate gave high connectivity of Ni electrode, high capacitance, small dissipation factor, high breakdown voltage, and high reliability of MLCC chips.