• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.158-159
• /
• 2007

In this paper a novel structure of multi-level converter for reducing ripple of output voltage is proposed. In the proposed converter Buck converters are connected in series to generate the output voltage and the ripple of output voltage can be reduced compared with the exiting Buck converter. Especially when outputting lower output voltage the number of acting switching elements is less and the result of ripple reducing is more obvious. It is expected that the converter proposed in this paper can be very useful in the case of wide range of output voltage.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.265-266
• /
• 2015

A multiple output dc-dc resonant converter topology for an independent voltage control technique is proposed, using a narrow frequency selection band-pass filters. The multi-output converter is supplied by a single source inverter with the superposed sinusoidal signals reserved for each output. A series-series parallel resonant topology is utilized to implement the narrow frequency selection channels for minimum interference. Finally the experimental setup for four output dc-dc converter is verified with the narrow channel frequencies of 26 kHz, 32 kHz, 38 kHz and 46 kHz.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.6
• /
• pp.314-324
• /
• 2006

In recent years, having the advantages of being small, low in cost and high in efficiency, Half-wave resonant type, (having only one output diode), is used in ZVS Half-Bridge DC/DC converter. This paper presents the operation mode by multi-resonant factors in the Half-wave type multi-resonant converter with direct Buck chopper circuit operated in discontinuous current mode. To study the characteristics of a multi-resonant operation in steady-state, the characteristic impedances in each mode and safe operation-region(S.O.R) are reported. Computer simulation and experimental data are also riven to verify the theoretical results.

• Journal of Communications and Networks
• /
• v.7 no.3
• /
• pp.284-293
• /
• 2005

A critical issue in applications involving networks of wireless sensors is their ability to synchronize, and mitigate the fading propagation channel effects. Especially when distributed 'slave' sensors (nodes) reach-back to communicate with the 'master' sensor (gateway), low power cooperative schemes are well motivated. Viewing each node as an antenna element in a multi-input multi-output (MIMO) multi-antenna system, we design pilot patterns to estimate the multiple carrier frequency offsets (CFO), and the multiple channels corresponding to each node-gateway link. Our novel pilot scheme consists of non-zero pilot symbols along with zeros, which separate nodes in a time division multiple access (TDMA) fashion, and lead to low complexity schemes because CFO and channel estimators per node are decoupled. The resulting training algorithm is not only suitable for wireless sensor networks, but also for synchronization and channel estimation of single- and multi-carrier MIMO systems. We investigate the performance of our estimators analytically, and with simulations.

• Journal of Communications and Networks
• /
• v.14 no.4
• /
• pp.443-450
• /
• 2012

As for cluster-based wireless sensor networks (WSNs), cluster lifetime is one of the most important subjects in recent researches. Besides reducing the energy consumptions of the clusters, it is necessary to make the clusters achieve equal lifetimes so that the whole network can survive longer. In this paper, we focus on the cluster lifetimes in multi-hop WSNs with cooperative multi-input single-output scheme. With a simplified model of multi-hop WSNs, we change the transmission schemes, the sizes and transmission distances of clusters to investigate their effects on the cluster lifetimes. Furthermore, linear and uniform data aggregations are considered in our model. As a result, we analyze the cluster lifetimes in different situations and discuss the requirements on the sizes and transmission distances of clusters for equal lifetimes.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.7
• /
• pp.352-360
• /
• 2003

This paper deals with a simple method in order to analyze and compare the harmonic characteristics in the multi-level inverter. Generally, the magnitude of harmonic components becomes different according to the multi-carrier Pulse Width Modulation(PWM) techniques, the modulation index($M_i$) and the switching frequency The previous papers analyzed the harmonic characteristics from the viewpoint of the space voltage vector. Hence, the calculation of the harmonic vector becomes more difficult and complex in 4-level or over 5-level. However, the proposed method has reduced an amount of calculation and simplified the process of it, using the relationship between the reference voltage and the output phase voltage to the load neutral point. It is applied to the 5-level cascade inverter and the harmonic characteristics for each multi-carrier PWM technique are compared through the simulation.

• Journal of information and communication convergence engineering
• /
• v.8 no.4
• /
• pp.393-398
• /
• 2010

For multi-cell environments, coordinated random beamforming technique in multiuser MIMO(multiple-input multiple-output) broadcast channel is considered. In order to mitigate severe interference at receivers, the multi-cell environments might require complex transmitter and receiver design because the scheduler decision based on full channel state information (CSI) in one cell must be intertwined with decision made by other cells' CSI. With limited CSI, however, this paper considers a scheme of randomizing transmitters' beamforming but being coordinated with other cell transmitters. The transmitters in each cell share random beamforming patterns and schedule data transmission within coherent scheduling period. The corandomized beams allow the users to be selected with the highest SINRs even in multi-cell environments. We analyze the performance of the proposed scheme. And numerical results show that the scheme achieves better performance than the conventional random beamforming when applying to multi-cell environments.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.12
• /
• pp.1878-1888
• /
• 1990

In this paper, the input-output interconnection method of the multi-valued signal processing circuit using perfect Shuffle technique and Kronecker product is discussed. Using this method, the design method of circuit of the multi-valued Reed-Muller expansions(MRME) to be used the multi-valued signal processing on finite field GF(p**m) is presented. The proposed input-output interconnection method is shown that the matrix transform is efficient and that the module structure is easy. The circuit design of MRME on FG(p**m) is realized following as` 1) contructing the baisc gates on GF(3) by CMOS T gate, 2) designing the basic cells to be implemented the transform and inverse transform matrix of MRME using these basic gates, 3) interconnecting these cells by the input-output interconnecting method of the multivalued signal processing circuits. Also, the circuit design of the multi-valued signal processing function on GF(3\ulcorner similar to Winograd algorithm of 3x3 array of DFT (discrete fourier transform) is realized by interconnection of Perfect Shuffle technique and Kronecker product. The presented multi-valued signal processing circuits that are simple and regular for wire routing and posses the properties of concurrency and modularity are suitable for VLSI.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.7
• /
• pp.575-582
• /
• 2004

The observer design problem is studied for a class of multi-output nonlinear systems that are not necessarily observable. Generalized nonlinear observer canonical form is introduced for multi-output nonlinear systems to design nonlinear observers. Sufficient conditions are given for a nonlinear system to be transformed by state-space change of coordinates into generalized nonlinear observer canonical form. Based on this canonical from, a sufficient condition is also given for the existence of nonlinear observers. An illustrative example is presented to show the design procedure of the proposed method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.5
• /
• pp.415-421
• /
• 2014

This study proposes a model-based predictive control for interleaved multi-phase DC/DC converters. The power values necessary to adjust the output voltage in the succeeding are predicted using a converter model. The output power is controlled by selecting the optimal duty cycle. The proposed method does not require controller loops and modulators for converter switching. This method can control the converter by calculating the optimal duty cycle, which minimizes the error between the reference and actual output voltage. The effectiveness of the proposed method is verified through simulations and experiments.