• ETRI Journal
• /
• v.26 no.6
• /
• pp.605-614
• /
• 2004

In this paper, we investigate array calibration algorithms to derive a further improved version for correcting antenna array errors and RF transceiver errors in CDMA smart antenna systems. The structure of a multi-channel RF transceiver with a digital calibration apparatus and its calibration techniques are presented, where we propose a new RF receiver calibration scheme to minimize interference of the calibration signal on the user signals. The calibration signal is injected into a multi-channel receiver through a calibration signal injector whose array response vector is controlled in order to have a low correlation with the antenna response vector of the receive signals. We suggest a model-based antenna array calibration to remove the antenna array errors including mutual coupling errors or to predict the element patterns from the array manifold measured at a small number of angles. Computer simulations and experiment results are shown to verify the calibration algorithms.

• Journal of electromagnetic engineering and science
• /
• v.4 no.2
• /
• pp.56-62
• /
• 2004

We present a multi-Gbit/s digital I/O interface based on RF-modulation and capacitive-coupling over an impedance matched transmission line. The RF-interconnect(RFI) can greatly reduce the digital switching noise and eliminate the dc power dissipation over the channel. It also enables reduced signal amplitude(as low as 200 ㎷) with enhanced data rate and affordable circuit overhead. This paper addresses the system advantages and implementation issues of RFI. A prototype on-chip RFI transceiver is implemented in 0.18-${\mu}{\textrm}{m}$ CMOS. It demonstrates a maximum data rate of 2.2 Gbit/s via 10.5-㎓ RF-modulation. The RFI can be very instrumental for future high-speed inter- and intra-ULSI data links.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.295-301
• /
• 2011

A triple-band transceiver module for 2.3/2.5/3.5 GHz mobile WiMAX, IEEE 802.16e, applications is introduced. The suggested transceiver module consists of RFIC, reconfigurable/multi-resonance MIMO antenna, embedded PCB, mobile WiMAX base band, memory and channel selection front-end module. The RFIC is fabricated in $0.13{\mu}m$ RF CMOS process and has 3.5 dB noise figure(NF) of receiver and 1 dBm maximum power of transmitter with 68-pin QFN package, $8{\times}8\;mm^2$ area. The area reduction of transceiver module is achieved by using embedded PCB which decreases area by 9% of the area of transceiver module with normal PCB. The developed triple-band mobile WiMAX transceiver module is tested by performing radio conformance test(RCT) and measuring carrier to interference plus noise ratio (CINR) and received signal strength indication (RSSI) in each 2.3/2.5/3.5 GHz frequency.

• ETRI Journal
• /
• v.26 no.3
• /
• pp.229-240
• /
• 2004

This paper reports on our development of a dual-mode transceiver for a CMOS high-rate Bluetooth system-onchip solution. The transceiver includes most of the radio building blocks such as an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, a variable gain amplifier (VGA), a dc offset cancellation circuit, a quadrature local oscillator (LO) generator, and an RF front-end. It is designed for both the normal-rate Bluetooth with an instantaneous bit rate of 1 Mb/s and the high-rate Bluetooth of up to 12 Mb/s. The receiver employs a dualconversion combined with a baseband dual-path architecture for resolving many problems such as flicker noise, dc offset, and power consumption of the dual-mode system. The transceiver requires none of the external image-rejection and intermediate frequency (IF) channel filters by using an LO of 1.6 GHz and the fifth order onchip filters. The chip is fabricated on a $6.5-mm^{2}$ die using a standard $0.25-{\mu}m$ CMOS technology. Experimental results show an in-band image-rejection ratio of 40 dB, an IIP3 of -5 dBm, and a sensitivity of -77 dBm for the Bluetooth mode when the losses from the external components are compensated. It consumes 42 mA in receive ${\pi}/4-diffrential$ quadrature phase-shift keying $({\pi}/4-DQPSK)$ mode of 8 Mb/s, 35 mA in receive GFSK mode of 1 Mb/s, and 32 mA in transmit mode from a 2.5-V supply. These results indicate that the architecture and circuits are adaptable to the implementation of a low-cost, multi-mode, high-speed wireless personal area network.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1304-1310
• /
• 2010

This study is to design FMCW radar transceiver of K-band which is used to detect and track approaching high speed targets with low altitude. The transmitter needs high output power due to small RCS targets and wide beamwidth of transmit antenna. Multi-channel receivers are required to detect and track targets by interferometer method. Transmitter consists of high power amplifier, waveguide switch, and frequency up-converter. Receiver is composed of five channel receivers, up and down converters, X-band local oscillator and waveform generator. Before manufacturing it, the proposed architecture of transceiver is proved by modeling and simulation using several parameters. Then, it is manufactured by using industrial RF components. The performance parameters are measured through experiment. In the experiment, transmitting power and receiver gain were measured with 39.64 dBm and 29.1 dB, respectively. All other parameters in the specification were satisfied as well.

• Journal of Satellite, Information and Communications
• /
• v.7 no.1
• /
• pp.75-81
• /
• 2012

This study is to design the transmitter and receiver of short range UWB(Ultra Wide Band) imaging radar that is able to display high resolution radar image for front area of a UGV(Unmanned Ground Vehicle). This radar can help a UGV to navigate autonomously as it detects and avoids obstacles through foliage. The transmitter needs two transmitters to improve the azimuth resolution. Multi-channel receivers are required to synthesize radar image. Transmitter consists of high power amplifier, channel selection switch, and waveform generator. Receiver is composed of sixteen channel receivers, receiver channel converter, and frequency down converter, Before manufacturing it, the proposed architecture of transceiver is proved by modeling and simulation using several parameters. Then, it was manufactured by using industrial RF(Radio Frequency) components and all other measured parameters in the specification were satisfied as well.

• Journal of KIISE:Information Networking
• /
• v.37 no.3
• /
• pp.217-227
• /
• 2010

To apply active RFID technology in the various kinds of industry, it needs to quickly transmit a large amount of data. ISO/IEC 18000-7 standard uses the 433.92MHz as single channel system and its transmit rate is just 27.8kbps, that is insufficient for a large amount of data transmission. To solve this problem, we designed a new data transmission protocol using 2.4GHz band. The feature of designed protocol is not only making over 255bytes data messages using the Burst Read UDB but also efficiently transmitting it. To implement this protocol, we use Texas Instruments's SmartRF04 develop kit and CC2500 transceiver as RF module. As an evaluation of 63.75kbytes data transmission, we demonstrate that transmission time of Burst Read UDB has improved as 17.95% faster than that of Read UDB in the ISO/IEC 18000-7.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.11A
• /
• pp.1146-1153
• /
• 2007

In this paper, we analyze the I/Q imbalances effects at the WiBro uplimk when using direct-conversion RF transceiver. If I/Q imbalance exists, the transmit signal is spread over two sbcarriers. As a result, phenomenon of performance reducing is produced. Contrary to OFDM system in which one user uses all subcarrier, symmetrical two subcarriers are assigned other users in OFDMA system. I/Q imbalances elements can't be estimated such a conventional allocation method of tiles in subchannel and compensated. In order to solve the problem, We propose a new method in order that symmetrical two subcarriers are assigned one user. If novel method is applied, we can estimate I/Q imbalances and compensate distortion received signal. As a result, we can obtain a performance similar performance when I/Q imbalances is not existed. Also, if proper detection methods are used, we get the effect of performance improvement, because of diversity gain what is happened due to combining I/Q imbalances with multi path fading channel.