• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2003년도 The Fifth Asian Computational Fluid Dynamics Conference
• /
• pp.240-242
• /
• 2003

A method for performing two-dimensional lift-constraint drag minimization in inviscid compressible flows on unstructured meshes is developed. Sensitivities of objective function with respect to the design variables are efficiently obtained by using a continuous adjoint method. In addition, parallel algorithm is used in multi-point design optimization to enhance the computational efficiency. The characteristics of single-point and multi-point optimization are examined, and the comparison of these two method is presented.

• Structural Engineering and Mechanics
• /
• 제87권1호
• /
• pp.47-56
• /
• 2023

Any pre-existed delamination defect present during manufacturing or induce during service loading conditions in the wingskin adherend invariably shows a greater loss of structural integrity of the spar wingskin joint (SWJ). In the present study, inter-laminar delamination propagation at the critical location of the SWJ has been carried out using contact and multi-point constraint finite elements available with commercial FE software (ANSYS APDL). Strain energy release rates (SERR) based on virtual crack closure technique have been computed for evaluation of the opening (Mode-I), sliding (Mode-II) and cross sliding (Mode-III) modes of delamination by sequential release of multi point constraint elements. The variations of different modes of SERR are observed to be significant by considering varied delamination lengths, material properties of adherends and radius of curvature of the SWJ panel. The SERR rates are seen to be much different at the two pre-embedded delamination ends. This shows dissimilar delamination propagation rates. The maximum is seen to occur in the delamination front in the unstiffened region of the wingskin. The curvature geometry and material anisotropy of SWJ adherends significantly influences the SERR values. Increase in the SERR values are observed with decrease in the radius of curvature of wingskin panel, keeping its width unchanged. SWJs made with flat FRP composite adherends have superior resistance to delamination damage propagation than curved composite laminated SWJ panels. SWJ made with Boron/Epoxy (B/E) material shows greater resistance to the delamination propagation.

• 산업경영시스템학회지
• /
• 제35권4호
• /
• pp.126-132
• /
• 2012

This paper deals with a centralized warehouse problem with multi-item and capacity constraint. The objective of this paper is to decide the number and location of centralized warehouses and determineorder quantity (Q), reorder point (r) of each centralized warehouse to minimize holding, setup, penalty, and transportation costs. Each centralized warehouse uses continuous review inventory policy and its budget is limited. A SA (Simulated Annealing) approach is developed and its performance is tested by using some computational experiments.

• 산업경영시스템학회지
• /
• 제31권4호
• /
• pp.134-139
• /
• 2008

Most approaches for continuous review inventory problem need tables for loss function and cumulative standard normal distribution. Furthermore, it is time-consuming to calculate order quantity (Q) and reorder point (r) iteratively until required values are converged. The purpose of this paper is to develop a direct method to get the solution without any tables. We used approximation approaches for loss function and cumulative standard normal distribution. The proposed method can get the solution directly without any iterative procedure for Q, r and without any tables. The performance of the proposed approach is tested by using numerical examples. The budget constraint of this paper assumes that purchasing costs are paid at the time an order is arrived. This constraint can be easily replaced by capacity constraint or budget constraint in which' purchasing costs are paid at the time an order is placed.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 하계종합학술대회 논문집(2)
• /
• pp.459-462
• /
• 2004

In this paper, we present a reducing power consumption of a scheduling for module selection under the time constraint. A a reducing power consumption of a scheduling for module selection under the time constraint execute scheduling and allocation for considering the switching activity. The focus scheduling of this phase adopt Force-Directed Scheduling for low power to existed Force-Directed Scheduling. and it constructs the module selection RT library by in account consideration the mutual correlation of parameters in which the power and the area and delay. when it is, in this paper we formulate the module selection method as a multi-objective optimization and propose a branch and bound approach to explore the large design space of module selection. Therefore, the optimal module selection method proposed to consider power, area, delay parameter at the same time. The comparison experiment analyzed a point of difference between the existed FDS algorithm and a new FDS_RPC algorithm.

• 한국정보통신학회논문지
• /
• 제12권6호
• /
• pp.1056-1063
• /
• 2008

부호화율과 구속장을 선택적으로 지정할 수 있는 다중 표준용 파라미터화된 비터비 복호기의 효율적인 설계에 대해 기술한다. 설계된 비터비 복호기는 부호화율 1/2과 1/3, 구속장 7과 9를 지원하여 4가지 모드로 동작하도록 파라미터화된 구조로 설계되었으며, 각 동작모드에서 공통으로 사용되는 블록들의 공유가 극대화되는 회로구조를 적용하여 면적과 전력소모가 최소화되도록 하였다. 또한, one-point 역추적 알고리듬에 최적화된 ACCS (Accumulate-Subtract) 회로를 적용하였으며, 이를 통해 완전 병렬구조에 비해 ACCS 회로의 면적을 약 35% 감소시켰다. 설계된 비터비 복호기 코어는 0.35-um CMOS 셀 라이브러리로 합성하여 79,818 게이트와 25,600비트의 메모리로 구현되었으며, 70 MHz 클록으로 동작하여 105 Mbps의 성능을 갖는다. 설계된 비터비 복호기의 BER (Bit Error Rate) 성능에 대한 시뮬레이션 결과, 부호화율 1/3과 구속장 7로 동작하는 경우에 3.6 dB의 $E_b/N_o$에서 $10^{-4}$의 비트 오류율을 나타냈다.

• 대한기계학회논문집A
• /
• 제25권5호
• /
• pp.779-787
• /
• 2001

The multi degree of freedom system using magnetic levitation has been implemented successfully. Differently from another noncontact systems, the developed system was focused on the maximization of the system stiffness under the constraint of a limited input. The variation of a relative adopting point between the magnetic pair, its location on the fixed base, and the selection of optimal specifications for the main active magnetic elements give us another chance to realize the increased robustness against external disturbances with the less control inputs. In this paper, the overall development procedures are given including the optimal design, the dynamic modeling, the various control tests, and the main issues to be solved.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제8권9호
• /
• pp.3196-3210
• /
• 2014

This paper presents a novel video metrology approach based on robust tracking. From videos acquired by an uncalibrated stationary camera, the foreground likelihood map is obtained by using the Codebook background modeling algorithm, and the multiple moving objects are tracked by a combined tracking algorithm. Then, we compute vanishing line of the ground plane and the vertical vanishing point of the scene, and extract the head feature points and the feet feature points in each frame of video sequences. Finally, we apply a single view mensuration algorithm to each of the frames to obtain height measurements and fuse the multi-frame measurements using RANSAC algorithm. Compared with other popular methods, our proposed algorithm does not require calibrating the camera, and can track the multiple moving objects when occlusion occurs. Therefore, it reduces the complexity of calculation and improves the accuracy of measurement simultaneously. The experimental results demonstrate that our method is effective and robust to occlusion.

• 로봇학회논문지
• /
• 제2권4호
• /
• pp.310-316
• /
• 2007

The paper proposes a human-following behavior of mobile robot and an intelligent space (ISpace) is used in order to achieve these goals. An ISpace is a 3-D environment in which many sensors and intelligent devices are distributed. Mobile robots exist in this space as physical agents providing humans with services. A mobile robot is controlled to track a walking human using distributed intelligent sensors as stably and precisely as possible. The moving objects is assumed to be a point-object and projected onto an image plane to form a geometrical constraint equation that provides position data of the object based on the kinematics of the intelligent space. Uncertainties in the position estimation caused by the point-object assumption are compensated using the Kalman filter. To generate the shortest time trajectory to track the walking human, the linear and angular velocities are estimated and utilized. The computer simulation and experimental results of estimating and trackinging of the walking human with the mobile robot are presented.

• 한국항공우주학회지
• /
• 제42권11호
• /
• pp.911-918
• /
• 2014

본 논문에서는 응집영역 모델링 방법에 의한 균열전파 해석에서 발생하는 연성추가문제의 효과적인 해결방법으로 사용자 부프로그램 UMPC를 이용한 응집요소의 선택적 활성화 기법을 연구 하였다. 먼저 균열의 발생 및 전파가 예상되는 지역의 일반요소들 사이에 응집요소를 삽입하고 응집요소를 구성하는 절점에 다중점 구속조건을 적용함으로써 응집 요소를 비활성화 시킨 상태로 해석을 시작한 후, 해석 도중에 특정 조건을 만족하는 절점들에 대해서만 다중점 구속조건을 해제하여 응집요소를 선택적으로 활성화하는 전략을 사용하였다. 응집요소의 초기강성 및 다중점 구속조건 해제 지표가 균열전파 거동 및 계산시간에 미치는 영향을 체계적으로 조사하였다.