• Atmosphere
• /
• v.24 no.2
• /
• pp.197-206
• /
• 2014

The effects of different averaging operators and atmospheric stability on the turbulent fluxes are investigated using the vertical velocity, air temperature, carbon dioxide concentration, and absolute humidity data measured at 10 Hz by a 3-dimensional sonic anemometer and an open-path $CO_2/H_2O$ infrared gas analyzer installed at a height of 18.5 m on the rooftop of the Jungnang KT building located at a typical residential area in Seoul, Korea. For this purpose, 7 different averaging operators including block average, linear regression, and moving averages during 100 s, 300 s, 600 s, 900 s, and 1800 s are considered and the data quality control procedure such as physical limit check and spike removal is also applied. It is found that as the averaging interval becomes shorter, turbulent fluxes computed by the moving average become smaller and the ratios of turbulent fluxes computed by the 100 s moving average to the fluxes by the 1800 s moving average under unstable stability are smaller than those under neutral stability. The turbulent fluxes computed by the linear regression are 85~92% of those computed by the 1800 s moving average and nearly the same as those computed by 900 s moving average, implying that the adequate selection of an averaging operator and its interval will be very important to estimate more accurate turbulent fluxes at urban area.

• The Journal of Engineering Geology
• /
• v.17 no.4
• /
• pp.507-510
• /
• 2007

The correlation between groundwater level(GWL) and the moving average of precipitation was analyzed based on the observation data in Nakdong river watershed. The precipitation data was compared and analyzed with the GWL data from adjacent observation point to the precipitation gauge station. The correlation between the moving average of precipitation with several averaging periods and GWL were analyzed and we could choose the averaging period that produces maximum correlation. A severe drawdown was observed from December to April. The maximum correlations between GWL and the moving average of precipitation were occurred from 20-day to 80-day averaging period.

• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.44-54
• /
• 1998

In this study a new arc sensor algorithm for automatic weld seam tracking was proposed, which uses the relative welding current variation according to the tip-to-workpiece distance in GMA welding. Since the new developed arc sensor algorithm is not sensitive to unstable factors of arc signal, the system is expected to get rid of the problems of already existing arc sensor system which include the difficulty of modeling the process for various welding conditions and limitation of application to thick plate welding. Thus the system is applicable not only to thick plate welding but also to thin plate welding. To implement the new arc sensor algorithm the system parameters which include sampling time, averaging range, weighting factor of moving averaging, basic compensation time, and basic compensation distance were determined by experimental analysis. Consequently this system has shown the successful tracking capability for the various welding conditions.

• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.55-63
• /
• 1998

Among the position sensing methods available, the arc sensor which utilizes the electrical signal obtained from the welding arc itself is one of the most prevalently used methods, because it has an advantage that no particular sensing device is necessary and real-time sensing of a groove position is possible directly under the arc. The authors have already developed a seam tracking system that contains a new arc sensor algorithm, which uses the relative welding current variation according to the tip-to-workpiece distance in GMA welding. In this study a torch height control algorithm for automatic weld seam tracking was proposed for completing the previous system, which uses an on-off control technique. To implement the torch height control algorithm during weld seam tracking the system parameters which include 2nd averaging range, weighting factor for 2nd moving averaging, and Z-directional basic compensation distance were determined by experimental analysis. Finally the two different height control methods, one is simple on-off control and the other on-off control using a reference current value , were compared in their tracking abilities.

• Tribology and Lubricants
• /
• v.36 no.2
• /
• pp.68-74
• /
• 2020

In this study, the effect of the shape error of a guideway on the movement of a stage that uses an air bearing is analyzed. The shape error of moving parts supported by the air bearing is known not to affect the vibrations of moving parts as much as the magnitude of the shape error. This is called the "averaging effect." In this study, the effect of shape error on a guideway, as well as the averaging effect of an air-bearing system, is analyzed theoretically using a dynamic-analysis program. The dynamic-analysis program applies a commercially available code in COMSOL and solves the Reynolds equation between the stage and the guideway, along with the equation of motion of the stage. The stage is modeled as a two-degree-of-freedom system. The shape error is applied to the film thickness function in the form of a sine wave. The stage movement is analyzed using the fast Fourier transform process. The eccentricity and tilting are found to be proportional to the amplitude of the shape error of the guideway. Stage vibrations are less than 10% of the amplitude of the shape error on the guideway. This means that the averaging effect of the air bearing is verified quantitatively. Moreover, if the air supply position matches the shape error in the guideway, there is a notable change in eccentricity and tilting.

• The Journal of Engineering Geology
• /
• v.18 no.1
• /
• pp.1-6
• /
• 2008

Precipitation and groundwater level data sets from Kum river watershed were analyzed and compared. The correlation between groundwater level and the moving average of precipitation was analyzed. Moving averaging technique is stochastic method and that was used to consider the effect of precipitation events on groundwater level fluctuation. Groundwater level generally follows seasonal precipitation pattern and low level occurs from early December to late April. Relatively high groundwater level is appeared in wet spell (July and August). The correlation between groundwater level and the moving average of precipitation to consider precedent precipitation events was analyzed with minimum two-year data sets. When the precipitation and groundwater level data set pair was selected the precipitation gauge station is closely located to groundwater level gauge station in the upstream direction to minimize the non-homogeneous precipitation distribution effect. The maximum correlation was occurred when the averaging periods were from 10 days to 150 days with Kum river watershed data. The correlation coefficients are influenced by data quality, missing data periods, or snow melt effect, etc. The maximum coefficient was 0.8886 for Kum river watershed data.

• Journal of KIISE
• /
• v.42 no.6
• /
• pp.769-780
• /
• 2015

Smoothing a digital curve by averaging its connected points is widely employed to minimize sharp changes of the curve that are generally introduced by noise. An appropriate degree of smoothing is critical since the area or features of the original shape can be distorted at a higher degree while the noise is insufficiently removed at a lower degree. In this paper, we provide a mathematical relationship between the parameters, such as the number of iterations, average distance between neighboring points, weighting factors for averaging and the moving distance of the point on the curve after smoothing. Based on these findings, we propose to control the smoothed curve such that its deviation is bounded particular error level as well as to significantly expedite smoothing for a pixel-based digital curve.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.123-134
• /
• 2013

Strengthening vehicle emission regulation is one of important policies to improve air quality in urban area. Due to the limitation of specified driving cycles for certification test to reflect real driving conditions, additional off-cycle emission regulations have been adopted in US and being developed in Europe. The driving cycles of US or Europe have been used in emission certification for Korean light-duty vehicles, but it has not been known how well the driving cycles reflect various real driving patterns in Korea. In that point of view, it is required to estimate vehicle emission based on real road driving conditions to raise the effectiveness of vehicle emission regulation in Korea. In this study, real driving emission measurements have been conducted for three Korean light-duty vehicles with PEMS. The driving routes consisted of urban, rural and motorway in Seoul and Incheon. The data have been analyzed with various averaging methods including moving averaging windows method and compared to emission limits set with emission certification modes applied to tested vehicles. The results have shown that the real driving pollutant emissions of a gasoline and a LPG vehicles have been ranged quite lower than those of emission limits on CVS-75 driving cycle. But real driving NOx of a light duty diesel vehicle has been considerably higher than emission limit of NEDC driving cycle. The higher than expected NOx emission of a diesel vehicle might be caused by different strategy to control EGR in real driving condition from NEDC driving.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.7
• /
• pp.116-123
• /
• 1999

of a block if the method uses the quantization parameter depending on the bitrate control, and consequently it influence the image quality of video. In this paper, we propose a new method using the following three steps : calculating an averaging (Average of Sum, AS) value in each pixel's block of images, earning an average value of differences between each pixels and As (Differential Averaging Block Pixels, DABP), and finally achieving an improved coefficient values by the DABP and DCT coefficients. Simulation results show that the quality of moving picture could be improved by the proposed method.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.54-65
• /
• 1993

The paper describes and alternative method based on a new idea to measure the circular movement of machining centers. ISO has employed three testing methods for the acceptance tests of machine tools; the first is a rotating one-dimensional probe method, the second is a two-dimensional probe and a master circular ring, and the third is a kinematic ball bar. The last two methods were proposed and introduced by W. Knapp and J. B. Bryan, respectively. The newly developed method is superior to above two methods; the rotating angle can be detected and the rotating radius is variable. Circular movement errors of machining centers were investigated by the analysis of data measured by R- .THETA. method. Followint observations are obtained 1) The errors which depend on positions, i.e., periodical errors by the pitch of ball screws, errors by compensation of backlash and errors by perpendicularity of X and Y-axis, were analyzed. 2) The errors which depend on NC control system, i.e., errors by the unbalance of position-loop-gaians, errors by velocity-loop-gains and errors by feed speeds, were quantiatively analyzed. 3) The method of extracting error information, which uses moving technique of averaging angle and fourier's analysis data mesured by the R- .THETA. method, was proposed.