• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.6 s.171
• /
• pp.70-75
• /
• 2005

Many researches have been focused on optimal designs of a pole shape in order to reduce cogging torques, which are generated between permanent magnets and slots. In this paper, an adaptive controller is proposed fur reducing the effect of cogging torques in servo motors. The controller stabilizes the control system and shows an excellent trajectory tracking performance compared to the conventional PD controller.

• Proceedings of the KIPE Conference
• /
• 2018.11a
• /
• pp.175-176
• /
• 2018

This paper presents a method to estimate the parameter of permanent magnet synchronous motor using a least squares method. The approximate solution of the linear simultaneous equations is obtained by the pseudoinverse least squares method of the input current and output voltage data of the current controller. It is possible to obtain the current response of the same bandwidth to the general control target by using the Pole-zero Cancellation technique. This paper verifies the performance of the proposed method by comparing the results of estimation of parameters of different motors by simulation.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.310-313
• /
• 2019

This paper used the majority function to digitally filter back-electromotive force as an explanation of the Brushless DC MOTOR control algorithm. The cause and improvement of motor noise, which are operating in close proximity to high frequency sources, did not use conventional low pass filter and comparator elements. Also, they repeatedly output a noise-free BEMF signal for the input value of the majority detection filtering. These filtering steps can help reduce costs and minimize the area of a PCB by requiring relatively little hardware.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.510-513
• /
• 2009

In this paper, a novel speed control algorithm of DC motors is presented. The key contribution here is a simple speed controller only with speed feedback and without an inner current control loop. This is possible by adjusting the reference speed based on a certain rule. Therefore, the proposed speed controller here becomes simpler while maintaining the control performance. Moreover, with the proposed controller, the system response can be tuned with less complexity. This proposed control method is investigated both mathematically and experimentally.

• JOURNAL OF ELECTRICAL WORLD
• /
• s.247
• /
• pp.33-41
• /
• 1997

• JOURNAL OF ELECTRICAL WORLD
• /
• no.3 s.111
• /
• pp.34-39
• /
• 1986

• JOURNAL OF ELECTRICAL WORLD
• /
• no.11 s.131
• /
• pp.31-38
• /
• 1987

• JOURNAL OF ELECTRICAL WORLD
• /
• no.2 s.146
• /
• pp.35-42
• /
• 1989

• JOURNAL OF ELECTRICAL WORLD
• /
• no.1 s.145
• /
• pp.44-51
• /
• 1989

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.130-137
• /
• 2010

Due to test facility and specialty, it is physically difficult to conduct the modal tests of large-sized structures such as truck, bus and airplane. So, in case of a large-sized truck, the mode analysis on a full vehicle model comprised of reliable cabin, frame, and deck has been generally performed. However, the reliability of overall vibrational characteristics of the analytic model has not been fairly guaranteed by the testified models of each subsystem owing to the existence of cab suspension and the nonlinear mounting between a chassis frame and a special deck system. In this paper, a method to find out the modal characteristics of a large-sized military truck is presented. New modal test equipment is developed to set the boundary conditions of three military truck variants as close as a free-free condition. And the mode analysis method using coupled structure and dynamic models is established to consider the above-mentioned dynamic non-linearities of the vehicle itself. The usefulness of the suggested method is verified by comparing with the modal test results. Finally, the modal parameters of the final variant are extracted using the proved analytic method.