• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.118-123
• /
• 1999

The recycle of the polycarbonate(PC)/acrylonitrile-butadiene-styrene(ABS) separated from the instrument panel (In-Panel) of the automotive was investigated. The small amount of polyurethane(PU) foam contained in the separated PC/ABS decreased the mechanical properties of the recycled PC/ABS. However, it is found that the PU foam formed the dispered phase of small particles at high temperature ($260^{\circ}C$) under high shear of the twin extruder, whereas it formed the big particles at low extrusion temperature ($220^{\circ}C$). The mechanical properties of the recycled PC/ABS extruded at high temperature was better than those at low temperature, which enabled the recycled PC/ABS seperated from In-Panel to be applied to the radiator grille without the addition of the compatibilizers or virgin PC/ABS. This was ascribed to the smaller particle sizes of the PU foam formed at high extrusion temperature under high shear.

• Applied Chemistry for Engineering
• /
• v.24 no.2
• /
• pp.208-213
• /
• 2013

In this study, the effect of phosphorus flame retardants on the flame retardancy of the flexible polyurethane foam (PUF) was investigated. Tetramethylene bis(orthophosphorylurea) [TBPU] and phosphinyl alkylphosphate ester [CR-530], resorcinol bis diphenylphosphate [RDP], triethyl phosphate [TEP] were used as flame retardants. The results of thermogravimetric analysis (TGA) indicate that TBPU added PUF produces more charred residues than the other flame retardant added PUF. It was found that TBPU added PUF exhibits low mean heat release rate (HRR), peak HRR, effective heat of combusion (EHC), mass loss rate (MLR), CO yield and $CO_2$ compared to those other flame retardants.

• Journal of Mechanical Science and Technology
• /
• v.20 no.12
• /
• pp.2147-2158
• /
• 2006

The continuous wavelet transform (CWT) has a frequency-adaptive time-frequency tiling property, which makes it popular for the analysis of dispersive elastic wave signals. However, because the time-frequency tiling of CWT is not signal-dependent, it still has some limitations in the analysis of elastic waves with spectral components that are dispersed rapidly in time. The objective of this paper is to introduce an advanced time-frequency analysis method, called the dispersion-based continuous wavelet transform (D-CWT) whose time-frequency tiling is adaptively varied according to the dispersion relation of the waves to be analyzed. In the D-CWT method, time-frequency tiling can have frequency-adaptive characteristics like CWT and adaptively rotate in the time-frequency plane depending on the local wave dispersion. Therefore, D-CWT provides higher time-frequency localization than the conventional CWT. In this work, D-CWT method is applied to the analysis of dispersive elastic waves measured in waveguide experiments and an efficient procedure to extract information on the dispersion relation hidden in a wave signal is presented. In addition, the ridge property of the present transform is investigated theoretically to show its effectiveness in analyzing highly time-varying signals. Numerical simulations and experimental results are presented to show the effectiveness of the present method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.4
• /
• pp.137-145
• /
• 2011

This paper suggests possible rear body shape modifications of a passenger car for the improvement of aerodynamic performance, based on the CFD analysis results. YF SONATA, a passenger car of Hyundai Motors Company, plays a major role as the baseline car in this research. Representatively, three parts(trunk rear edge, side rear edge and rear undercover) are modified in a small range in order for the total outer shapes not to be changed enough so that the modified car is not considered different, compared with the baseline. Specifically, using computational fluid dynamics, aerodynamic drag reduction is accomplished maximally about 11% in this research. Finally, it is proved that although the range of changes of the rear body shapes of a passenger car is very strictly confined, by changing a small range of rear body shapes alone the enhancement of aerodynamic performance of a passenger car can be significantly accomplished.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.87-93
• /
• 2007

It is complicate to analysis the systems, dual mode hybrid systems, because they are composed of many planetary gear sets. For the performance test, it needs to define the systems with representative parameters. In this paper, system parameters, $\alpha$, $\beta$, $\zeta$, are introduced to define the systems, and an arbitrary system like E-IVT developed by Renault Motors is converted to the general system having equivalent parameters, such as $\beta'$, $R'_b$. Pontryagin principle and Kuhn-Tucker condition method are applied to solve the constrained problems, by which the methodology for accelerating test is generalized, and the results of the simulation are reported. In addition, the effects of alternative strategies are mentioned. The method of fuel economy test at engine mode is also introduced. The results of test at engine mode is different from the results of optimal trajectory, but the fuel economy of the engine mode is related to the highway driving and optimized operating of the system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.23-30
• /
• 2014

This paper proposes a dead time compensation method for an AC motor drive using phase current polarity information which is detected based on a digital programmable low-pass filter (PLPF). The polarity detection using the PLPF is an alternative solution of a conventional method which uses a general low-pass filter (LPF) and hysteresis bands in order to avoid jittering due to noises. The PLPF not only adjusts its cutoff frequency according to the synchronous frequency of AC motors but also eliminates a gain attenuation and phase delay which are main problems of the general LPF. Through the PLPF, a fundamental component signal without gain and phase distortions is extracted from the measured raw current signal with noise. By use of the fundamental component, the polarity of current is effectively detected by reducing the hysteresis band. Finally, the proposed method compensates the dead time effects by adding or subtracting average voltage value to voltage references of the controller according to the detected current polarity information. The proposed compensation method is experimentally verified by compared with the conventional method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.4
• /
• pp.327-334
• /
• 2013

In August 2012 the first CanSat competition was hosted by the Satellite Research Center of KAIST under auspice of the Ministry of Education, Science and Technology. The present authors team won the first prize in the university session. In this paper the overall procedure of the CanSat project presented from the conceptual design stage to the final launch test. As the compulsory mission CanSat should send GPS data and attitude information to the ground station which in practice was performed via Bluetooth channel. In addition our CanSat is designed to trace the sun for the solar panels supplying electric power of satellite. IMU and servo motors are used for the attitude control in order that the solar sensor of the CanSat is always direct towards the sun. Launching of CanSat was simulated by dropping from a balloon at the height of around 150m via parachute. Launching test results showed that the attitude control of the CanSat and its solar sensing function were successful.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.1
• /
• pp.57-65
• /
• 2001

The speed control without a speed sensor is expected strongly to progress reliability, simplicity and cost performance of Induction Motor(I.M) systems. Also, it contributes to expansion of I.M systems into various industrial application fields. This paper investigates a novel speed sensorless control method of I.M considering the secondary resistance identification based on the transientless torque control technique. Especially, this paper aimed at the identification of the secondary resistance simultaneously with speed estimation superposing of sinusoidal flux wave to a constant flux value. Furthermore, the secondary flux with some frequency is controlled independently on torque control. The proposed speed estimation method is derived from a motor circuit equation theoretically and also it can be conducted easily by detecting primary motor currents and primary voltage commands at every sampling time. Some numerical simulations with the assumption of using a pulse width modulation(PWM) voltage source inverter are performed to verify the proposed method.

• Fire Science and Engineering
• /
• v.30 no.2
• /
• pp.106-113
• /
• 2016

Ultra-high pressure positive displacement pump can discharge high pressure water with mass volume, which depends on periodic changes in volume that made by rotation motor. Its high efficiency of discharge is one of the most strong point of positive displacement pump. Due to its simple system structure, it can be miniaturized and lightened. Positive displacement pump can discharge high pressure with stable flow rate, irrespective of pressure fluctuate. This is the reason that positive displacement pump was used instead of centrifugal pump. In this study, shutoff operating system was developed for positive displacement pump to secure safety of high pressure operate. This shutoff system contains controller system, electronic clutch, and relief valve, and each part is mutual supplementation. Speed test was carried out in order to check operation of controller program and electronic clutch and fluid flow, venting experiment of the relief valve. It was confirmed that segment system of ultra-high pressure positive displacement pump is operated.

• Journal of Biosystems Engineering
• /
• v.26 no.2
• /
• pp.163-168
• /
• 2001

A manipulator for test-cup attachment modules, which was a part of a robot milking system, was developed to reduce cost and labor for cow milking processing. A Cartesian coordinate manipulator was designed for the milking process, because it was quite flexible and can be constructed more economically than any other configuration. The manipulator was made use of DC motors, screws for power transmission, a RS422 interface system for the transmission of coordinate values and a one-chip microprocessor, 89C52. Performance tests of the manipulator were conducted to measure experimentally the precision of all axes. Some of the results are as follows. 1. The Cartesian coordinate manipulator was designed and built. Dimension of the three perpendicular axes (X, Y, and Z) and one arm’s axis(W) to pick up and transfer the modules were 700㎜$\times$450㎜$\times$550㎜$\times$650㎜. The arm’s axis moved the teat-cup attachment module, which attached four teat-cup to four teats, detached four teat-cup from four teats, was designed and manufactured by using CAD, CAM and CNC. 3. After 10 replications of exercising the manipulator, mean precision values(positioning error) of X, Y, Z axes wee 0.48㎜, 0.20㎜, 0.19㎜, respectively. Therefore, we conclude the axes to have a precision better than 0.5㎜, had no problem to operate correctly the milking manipulator.