• The Transactions of the Korean Institute of Power Electronics
• /
• v.2 no.2
• /
• pp.49-56
• /
• 1997

Switched Reluctance Motors(SRMs) have a considerable inherent torque ripple due to the driving characteristics of pulse current waveform and the nonlinear variation inductance profile. This paper describes a current shape characteristics to effect a torque ripple reduction, and one pulse mode switching control method is proposed to minimize torque ripple of a switched reluctance motor regardless of speed and load condition by regulating tow parameters, such as, advance angle and exciting voltage. The experiments are performed to verify the capability of proposed switching method on 6/4 salient type SRM.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.591-595
• /
• 2000

In this paper we proposed a new sensorless drive system for the trapezoidal type brushless DC motor which does not use any mechanical position or speed sensor and applicable to the systems requiring a constant speed and torque such as Fan. For this a novel indirect rotor position sensing technique based on a detailed analysis of the terminal voltage characteristics is proposed in this paper. And a sensorless drive system for the brushless DC motor is implemented using a 87c196mc fo the main microprocessor and a power FET for the inverter. The experimental results will show the validity of the proposed indirect sensing method and the practical use of the sensorless drive

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.615-619
• /
• 2000

This paper presents an implementation of digital motion control system of Surface Permanent-Magnet Synchronous Motor(SPMSM) vector drives with a direct torque control(DTC) using the 16bit DSP TMS320F240 The DSP controller enable enhanced real time algorithm and cost-effective design of intelligent control for motors which can be yield enhanced operation fewer system components lower system cost increased efficiency and high performance The system presented are stator flux and torque observer of stator flux feedback model that inputs are current and voltage sensing of motor terminal and angle for a low speed operating area two hysteresis band controllers an optimal switching look-up table and IGBT voltage source inverter by using fully integrated control software. The developed control system are shown a good motion control response characteristic results and high performance features using 1.0Kw purposed servo drive SPMSM.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.705-708
• /
• 2000

Switched Reluctance motors(SRM) attract much attention in motor because they are reliable and inexpensive. With advance in power electronics and high-speed processors the performance of SRM has been enhanced greatly. But they require rotor position information to operate, In many systems rotor position sensors are undesirable and have disadvantages. To overcome the disadvantages include by position sensors a number of sensorless methods for SRM's have been proposed by researchers. This paper describes a method for indirect sensing of rotor position in SRM's pulsewidth modulation voltage control. The method required no priori knowledge of motor parameters excepts for the number of stator and rotor poles. The detection method uses the change of the derivative of the phase current to detect the position.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.203-206
• /
• 2000

This paper presents a torque ripple reduction technique of direct torque control(DTC) for high power induction motors driven by 3-level inverters with the inverter switching frequency limited around 0.5-1kHz level. It is noted that conventional DTC algorithms to reduce torque ripple are devised for applications with relatively high switching frequency above 2-3kHz. A new DTC algorithms especially for low switching frequency inverter system illustrates relatively reduced torque ripple are devised for applications with relatively high switching frequency above 2-3kHz. Anew DTC algorithm especially for low switching frequency inverter system illustrates relatively reduced torque ripple characteristics Simulation and experimental results show the effectiveness of the proposed control algorithm

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.311-318
• /
• 2005

이 논문은 다른 종류의 유도전동기 구름베어링 손상을 유도전동기 고정자 전류신호해석을 통하여 검출하고 실시간으로 손상을 진단하는 알고리즘을 개발하였다. 유도전동기 구름베어링의 손상을 검출하기 위하여 정상적인 베어링을 갖는 유도전동기, 축정열에 불량을 가지고 있는 전동기와 베어링 외륜에 구멍을 가지고 있는 2가지 종류의 비정상 베어링을 갖는 유도전동기 3set를 실험시스템을 구축하였다. 또한 유도전동기의 구름베어링시스템의 비정상적인 상태에서 고정자전류을 검출하기 위하여 TMS320F2407 DSP 칩을 이용하여 데이터 획득보드를 개발하였다. 이 고정자전류신호를 해석을 통하여 베어링 손상을 검출하기 위한 방법으로 FPT, 웨이브렛 분석 및 내적에 의한 평균신호패던에 의한 분석결과를 제시하였다. 특히 내적에 의한 신호분석을 통하여 베어링 손상 여부를 실시간으로 진단할 수 있는 새로운 알고리즘과 분석방법을 제시하였다.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.101-103
• /
• 2003

This paper presents the speed control of Brushless DC Motors using PI control. PI control is implemented by software using digital signal processor(DSP) TMS320F240 from Texas instruments. Considering the cost of BLDC Driver A. B. C phase hall IC's signal is used instead of incremental encoder. The Present paper describes, how to control a speed of BLDC Drive.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.107-109
• /
• 2003

Single phase induction motor is directly used usual source, it can be a source of an appliance such as mechanical fan, refrigerator, washing machine, etc. Especially capacitor-run single phase induction motor is suitable to make more inexpensive and high efficient products because it is more high efficiency, and good to start than other single phase induction motors. Generally, voltage and current of capacitor-run single phase induction motor transfer to the part of positive phase and negative phase based on two motor theory. In this paper, we simulate the torque characteristics to capacitance variation from single phase induction motor's equivalent circuit. Through the test using the real motor, we compare and investigate the maximum torque of run state related with capacitance and the adequacy of the converted model.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.123-125
• /
• 2004

This paper presents the application of response surface methodology (RSM) to design optimization for two types of synchronous reluctance motors (SynRMs); one has 12 slots with distributed winding, and the other has 6 slots with concentrated winding, to improve the ratio between torque ripple and average torque. The usefulness of RSM in optimization problem of SynRM is verified as compared with the results of finite element analysis. In the end, the optimized two SynRMs are compared with SynRM currently used in air-conditioning compressor in connection with torque performance and loss.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.116-118
• /
• 2003

The Slotless Permanet-magnet linear synchronous motors (PMLSM) have been developed for factory automation, transportation applications, wafer steppers, conveyance system, and so on[1]. The current analysis and design are treated in air-cored PMLSM. The main purpose of this paper is to provide a general design and analysis framework for the iron-cored linear permanent-magnet machines. Based on field solution using two dimensional analytical technique the magnetic field required magnet volume size, optimal winding thickness size, winding flux linkage and thrust will be discussed.