• ETRI Journal
• /
• v.37 no.6
• /
• pp.1165-1175
• /
• 2015

This paper presents an advanced sensorless permanent magnet (PM) brushless motor controller integrated circuit (IC) employing an automatic lead-angle compensator. The proposed IC is composed of not only a sensorless sine-wave motor controller but also an isolated gate-driver and current self-sensing circuit. The fabricated IC operates in sensorless mode using a position estimator based on a sliding mode observer and an open-loop start-up. For high efficiency PM brushless motor driving, an automatic lead-angle control algorithm is employed, which improves the efficiency of a PM brushless motor system by tracking the minimum copper loss under various load and speed conditions. The fabricated IC is evaluated experimentally using a commercial 200 W PM brushless motor and power switches. The proposed IC is successfully operated without any additional sensors, and the proposed algorithm maintains the minimum current and maximum system efficiency under $0N{\cdot}m$ to $0.8N{\cdot}m$ load conditions. The proposed IC is a feasible sensorless speed controller for various applications with a wide range of load and speed conditions.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.109-116
• /
• 2005

The high performance drives of the slotless Permanent Magnet Brushless DC(PM BLDC) motor can be achieved by the current control, where the currents flow according to the rotor position and the current phase is suitably controlled according to the operational condition. Rotor position information can be provided by Hall-IC or sensorless algorithm. So, the Hall-ICs are set up in this motor to detect the main flux from the rotor. Instead of using three Hall-ICs and encoder, this paper uses only two Hall-ICs for the permanent magnet rotor position and the speed feedback signals, and uses a micro-controller of 16-bit type (80C196KC). Also because of low resolution obtained by using Hall-IC even low-cost and simple structure, to improve the wide range of speed response characteristic more exactly, we propose the rotor position signal synthesizer using PLL circuit based on two Hall-ICs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.7
• /
• pp.563-566
• /
• 2009

This paper presents a motor drive IC for automotive applications. The drive IC is dedicated to control and drive external MOSFETs which directly drive 3-phase motor with a high current. In case of driving high-side power switches, the bootstrap topology is widely used. however, it requires three bootstrap diode and three capacitor respectively. And it needs a minimum charging time to maintain high-side voltage. The motor drive IC uses a charge-pump circuit for all three high-side voltage with various protection schemes for automotive applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.41-42
• /
• 2009

This paper presents a motor drive IC for automotive applications. The drive IC is dedicated to control and drive external MOSFETs which directly drive 3-phase motor with a high current. In case of driving high-side power switches, the bootstrap topology is widely used. However, it requires three bootstrap diode and three capacitor respectively. And it needs a minimum charging time to maintain high-side voltage. The motor drive IC uses a charge-pump circuit for all three high-side voltage with various protection schemes for automotive applications.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.341-344
• /
• 2000

본 논문에서는 stepper motor 나 BLDC motor를 구동하기 위하여, 최신 microcontroller, PC, control IC board 등으로 구성된 새로운 시스템을 설명하는데 목적이 있다. 이 시스템에서는 인터넷으로 전송되는 microcontroller program를 이용하여 SPDS(smart power development system)을 구동시키고, 이로 인하여 dedicated drive IC를 제어하여 stepper 또는 BLDC motor를 구동시키게 되며, 원격지에 있는 사용자의 motor를 제어함을 목표로 하고 있다. 본 논문에서 사용된 drive IC 는 SGS-Thomson 제품으로써 stepper motor 용으로 L6205/6/7/8, 그리고 BLDC motor 용으로 L6235 이다. SPDS는 ST92F120 16-bit microcontroller를 사용하고 있다. 이 논문에서는 인터넷 Protocol Converter에 의한 프로그램 전송, Operating System Program 및 Driver Software Program의 생성 및 구성, Drive IC의 구성 및 특징, SPDS 의 hardware 및 software 의 구성 등에 대하여 설명한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.686-692
• /
• 2002

본 논문은 Pyroelectric Sensor의 신호를 입력으로 받아 Stepping Motor 제어신호를 출력하는 Controller를 VHDL을 이용하여 ALTERA사의 EPM7128SLC84-7 CPLD칩으로 구현하여 자동문을 제작하였다. 동작은 센서부에서 사람을 감지하여 출력한 신호를 CPLD에서 받아들여 Stepping Motor구동부 회로의 제어신호로 사용하여 문을 동작시켰다.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.665-669
• /
• 2004

Generally, Slotless PM BLDC drive system is necessary that the three Hall-ICs evenly be distributed around the stator circumference and encoder be installed in case of the 3 phase motor. So, the Hall-ICs are set up in this motor to detect the main flux from the rotor, and the output signal from Hall-ICs is used to drive a power transistor to control the winding current. However, instead of using three Hall-ICs and encoder, we used only two Hall-ICs for the permanent magnet rotor position and for the speed feedback signals, and also for a microcontroller of 16-bit type (80C196KC) with the 3 phase Slotless PM BLDC whose six stator and two rotor designed. Two Hall-IC Hc and $H_B$ are placed on the endplate at 120 degree intervals, and with these elements, we can estimate information of the others phase in sequence through a rotating rotor.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1176-1187
• /
• 2015

This work proposes a highly efficient sensorless motor driver chip for various permanent-magnet synchronous motors (PMSMs) in a wide power range. The motor driver chip is composed of two important parts. The digital part is a sensorless controller consisting mainly of an angle estimation block and a speed control block. The analog part consists of a gate driver, which is able to sense the phase current of a motor. The sensorless algorithms adapted in this paper include a sliding mode observer (SMO) method that has high robust characteristics regarding parameter variations of PMSMs. Fabricated SMO chips detect back electromotive force signals. Furthermore, motor current-sensing blocks are included with a 10-bit successive approximation analog-to-digital converter and various gain current amplifiers for proper sensorless operations. Through a fabricated SMO chip, we were able to demonstrate rated powers of 32 W, 200 W, and 1,500 W.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.598-599
• /
• 2017

In motor application, High efficiency is important. So Design engineer select small gate resistor for lower switching. But There is side effect with small gate resistor. It makes large dv/dt and system request large EMI filter. It makes price increase. This paper introduce about gate drive IC which have solution both of lower loss and EMI issue.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.312-316
• /
• 1987

A simple hybrid circuit to control the two-phase AC motor of the nut-runners which employ the tightening torque control system is described in this paper. The circuit has emphasis on the low-cost implementation. The circuit constitutes of the V/F converter using a timer IC, the pulse width modulator using the fastening torque signal and the two-phase logic sequencer.