• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.106-106
• /
• 2000

This study is to embody automatic inspection system of motor body panel by visual system. since it is inefficient to examine the adhesion condition of components with the naked eye, picture processing algorithm is presented to replace the existing manual inspection process with an automatic inspection process. The developed automatic inspection system presents the examination method of the adhesion condition of components with a ixed camera, which leads to an increase of the productivity and a reduction of manufacturing cost.

• Corrosion Science and Technology
• /
• v.2 no.5
• /
• pp.247-251
• /
• 2003

The corrosion forms of automotive body panels are various. One of the representations is a corrosion pitting and its propagation on the lapped portion by galvanic corrosion. But it has been difficult in correlation analysis about the corrosion propagation rate and mechanism of pitting and the actual automotive body in field. This present study interprets experimentally the rust pitting occurrence mechanism on the lapped panels through experimental methods. And field car investigation was executed for correlation analysis with experimental results. This paper compares corrosion propagation rate by pitting on hot-dip galvannealed steel sheets with corrosion forms in the automotive field condition. The research fundamentals which make it possible to predict the pitting occurrence and propagation on the lapped panels in the actual vehicles are given.

• International Journal of Automotive Technology
• /
• v.8 no.1
• /
• pp.67-73
• /
• 2007

This study analyzes the interior noise that is generated during acceleration of a passenger car in terms of car body structure and panel contribution. According to the transfer method, interior noise is classified into structure-borne noise and air-borne noise. Structure-borne noise is generated when the engine's vibration energy, an excitation source, is transferred to the car body through the engine mount and the driving system and the panel of the car body vibrates. When structure-borne noise resonates in the acoustic cavity of the car interior, acute booming noise is generated. This study describes plans for improving the car body structure and the panel form through a cause analysis of frequency ranges where the sound pressure level of the rear seat relative to the front seat is high. To this end, an analysis of the correlation between body attachment stiffness and acoustic sensitivity as well as a panel sensitive component analysis were conducted through a structural sound field coupled analysis. Through this study, via research on improving the car body structure in terms of reducing rear seat noise, stable performance improvement and light weight design before the proto-car stage can be realized. Reduction of the development period and test car stage is also anticipated.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.51-56
• /
• 2000

This study is to implement automatic inspection system of motor body panel by visual system. since it is inefficient to examine adhesion condition of components with the naked eye, image processing algorithm is presented to replace the existing manual inspection process with an automatic inspection process the developed automatic inspection system presents tile examination method of the adhesion condition of components with a pixed camera, which leads to an increase of the productivity and a reduction of manufacturing cost

• International Journal of Korean Welding Society
• /
• v.3 no.1
• /
• pp.2-7
• /
• 2003

Laser welding application for car body manufacturing has many advantages in the stiffness and the lightness of vehicle, the productivity of assembly line, and the degree of freedom in design. This presentation will express the innovation of car body manufacturing including parameter optimization, process modeling, and system integration. In this application the investment for systems was cut down dramatically by real time switching over the laser path between two welding stations. Points of technical discussion are as follows; optimization of parameters such as laser power, robot speed and trajectory, compact and useful design of jig & fixture to assure welding quality for 3 sheet-layer zinc-coated steel, system integration between 4㎾ Nd:YAG laser device and the other systems, on-line real time welding quality monitoring system, perfect safety standards for high power laser, minimization of consumption costs such as arc lamp, protective glass for optic, etc. This application was successfully launched mass production line in 2001. The laser-welded line of side panel consists of 122 stitches totally. And the length is about 2.4m.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.175-181
• /
• 2007

The objective of this study was to develop formability evaluation techniques in order to apply aluminum sandwich panel for automotive body parts. For this purpose, newly adopting formability evaluation (using limit dome height and plane strain test) was carried out in order to secure the fundamental data for the measurement of sheet metal forming and the establishment of optimum forming conditions of the aluminum sandwich panel. The results showed that there were good agreements between the old formability evaluation method and the new method which was more simplified than that of old one. From the results of these formability evaluation, the formability of sandwich panel was higher than that of aluminum alloy sheet alone which was the skin component for the sandwich panel. Also, it was found that sandwich panel could reduce the weight and could have the same flexural rigidity simultaneously when it was compared to the automotive steel sheet.

• Journal of Welding and Joining
• /
• v.34 no.1
• /
• pp.21-25
• /
• 2016

The automotive vehicle is made through the following processes such as press shop, welding shop, paint shop, and general assembly. Among them, the most important process to determine the quality of the car body is the welding process. Generally, more than 400 pressed panels are welded to make BIW (Body In White) by using the RSW (Resistance Spot Welding) and GMAW (Gas Metal Arc Welding). Recently, as the needs of light-weight material due to the $CO_2$ emission issue and fuel efficiency, new joining technologies for aluminum, CFRP (Carbon Fiber Reinforced Plastic) and etc. are needed. Aluminum parts are assembled by the spot welding, clinching, and SPR (Self Piercing Rivet) and friction stir welding process. Structural adhesive boning is another main joining method for light-weight materials. For example, one piece aluminum shock absorber housing part is made by die casting process and is assembled with conventional steel part by SPR and adhesive bond. Another way to reduce the amount of the car body weight is to use AHSS (Advanced High Strength Steel) panel including hot stamping boron alloyed steel. As the new materials are introduced to car body joining, productivity and quality have become more critical. Productivity improvement technology and adaptive welding control are essential technology for the future manufacturing environment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.481-484
• /
• 2005

The AutoForm previously used the membrane element and it accomplished sheet metal forming analysis. The membrane analysis has been widely applied to various sheet metal forming processes because of its time effectiveness. However, it's well known that the membrane analysis can not provide correct information for the processes which have considerable bending effects. In this research it tried to compare the analysis results which use the shell element which is applied newly in the AutoForm commercial software with actual experimental results. The shell element is compromise element between continuum element and membrane element. The Finite element method by using shell element is the most efficient numerical method. From this research, it is known that FEA by using shell element can predict accurately the problems happened in actual experimental auto-body panel.

• Journal of the korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.19-26
• /
• 1981

자동차제조에 있어서의 용접은 신뢰성 양산과 생력화에 대응하여 접합 조립하는 방법으로 특이한 분야를 형성하여 발전되었다. 예를 들면, 자동차의 생산은 기본적으로 양산체제를 갖추고 있 어서, 일반적으로 노동집약형 산업이라고 불리어지며 그 제조공정을 보면 stamping press 공정과 같이 용접공정도 비교적 장치산업적인 분야로 빠르게 자동화나 성인화 내지 무인화로 진행되고 있다. 자동차용접은 사람이 portable spot welder로 한점씩 용접하지만 양산에 대비한 합리화와 안정화를 위하여 다점용접 (multi spot weld)라는 자동화공법의 도입이 불가피하며 금일의 자 동차생산에 있어서 상식화가 되고 있다. 이것은 한개의 차체라면 차형의 대조 또는 press panel의 수에 따라 차이가 조금 있으나 약 4-5 천점의 점용접이 필요하기 때문에 여러 가지 반송장치와 조합하여 대규모의 line설비로 발전되어 가고 있다. 이와 같이 용접공정의 자동화는 생산성을 높이는 반면에 전용성이 높기 때문에 설계변경에 대한 초기투자의 용접설비 대부분을 갱신하여야 하는 새로운 투자의 필요문제가 증대되었다. 이러한 전용설비에 대한 유연성을 가미한 자동차로 지향되어, 그 한 방법으로 산업용 robot가 도입되었다. 근래에 와서는 자동차제조에 있어서 새 로운 용접기술을 합리적으로 효과있게 적용하는 기술이 금후의 연구과제라 하겠다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.66-72
• /
• 2014

A kinematic analysis method has been used as analysis method for dynamic behavior of moving parts of vehicle, especially hood part. Such analysis method, however, has its limitations in terms of design technology, including, over travel of hood that occurs due to lack of considerations of compliance characteristics, such as flexible components of hood's weather strip and over slam bumper. Therefore, it is necessary to develop a modeling which reflects compliance of flexible components of hood and elastic characteristics of panel for improvement of design process. In this thesis, a finite element method as mentioned earlier, is developed to represent over travel of hood. Also optimization process applying sequential approximate optimization is suggested to prevent over travel. The over travel analysis method and optimization process, which are developed through the research, would make it possible to design with high quality and credibility. Furthermore, it is expected that the time for design would be reduced and the design quality also improved.