• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.428-433
• /
• 1997

This paper presents a new control strategy for the position and force control of flexible manipulators. The governing equation of motion of a two-link flexible manipulator which features piezoceramic actuators bonded on each flexible beam is derived via Hamilton's principle. The control torque of the motor to command desired position and force is determined by a sliding mode controller on the basis of the rigid-mode dynamics. In the controller formulation, the sliding mode controller with perturbation estimation(SMCPE) is adopted to determine appropriate control gains. The SMCPE is then incorporated with the fuzzy technique to mitigate inherent chattering problem while maintaining the stability of the system. A set of fuzzy parameters and control rules are obtained from a relation between estimated perturbation and actual perturbation. During the commanded motion, undesirable oscillation is actively suppressed by applying feedback control voltages to the piezoceramic actuators. These feedback voltages are also determined by the SMCPE. Consequently, accurate force and position control of a two-link flexible manipulator are achieved. Computer simulations are undertaken in order to demonstrate the effectiveness of the proposed control methodology.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.76-85
• /
• 1998

Recently, Genetic Algorithm(GA) is widely adopted into a search procedure for structural optimization, which is a stochastic direct search strategy that mimics the process of genetic evolution. This methods consist of three genetics operations maned selection, crossover and mutation. Contrast to traditional optimal design techniques which use design sensitivity analysis results, GA, being zero-order method, is very simple. So, they can be easily applicable to wide area of design optimization problems. Also, owing to multi-point search procedure, they have higher probability of converge to global optimum compared to traditional techniques which take one-point search method. In this study, a method of finding the optimum values of suspension parameters is proposed by using the GA. And vehicle is modelled as planar vehicle having 5 degree-of-freedom. The generalized coordinates are vertical motion of passenger seat, sprung mass and front and rear unsprung mass and rotate(pitch) motion of sprung mass. For rapid converge and precluding local optimum, share function which distribute chromosomes over design bound is introduced. Elitist survival model, remainder stochastic sampling without replacement method, multi-point crossover method are adopted. In the sight of the improvement of ride comfort, good result can be obtained in 5-D.O.F. vehicle model by using GA.

• Journal of Korean Physical Therapy Science
• /
• v.15 no.3
• /
• pp.55-63
• /
• 2008

Background : The Purposes of this study were to understand difference between free walking and obstacle over walking through the naked eye and motion analysis device, and to review merits of obstacle walking training as item of functional assessment in clinical situations. Methods : All participants were male and performed 3 types of walking methods: free walking, obstacle over walking with low block(height=10cm, width=8cm), and obstacle over walking with high block(height=20cm, width=8cm). All walking were performed 3 trials respectively. Results : In the naked eye, initial contact with toes occurred more than heel strike in obstacle over walking, and the flexion angle of hip and knee were increased in obstacle over walking. On interpretations though motion analysis device, cadence, gait speed and weight accept were significant statistically(p<.05). Cadence and gait speed were decreased, and weight accept duration was increased in obstacle over walking. Rotation among three pelvic motions was significant statistically(p<.05), flexion among three hip motions was significant statistically(p<.05) and flexion among three ankle motions was significant statistically(p<.05). Rotation and flexion among three ankle motions was significant statistically(p<.05). Conclusion : Both the naked eye and interpretations of the device presented many difference between free walking and obstacle over walking. In overcrossing obstacles, many participants appeared walking strategy by perform initial contact with toes. Knee flexion was most significant statistically(p<.05) in obstacle over walking with 20cm block.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.8
• /
• pp.729-734
• /
• 2015

Improvement in the control strategy for continuous casting is a crucial requirement to enhance the slab's quality and to increase productivity. The mold oscillator adopts the dual cylinders due to its heavy weight, so the synchronized motion of two cylinders is an important aspect when precise control is needed. The conventional method uses the master-slave control applied to the valve input reference, but the synchronization performance should still be improved. This paper proposes a novel synchronization algorithm for dual cylinders used in a mold oscillator. The master-slave concept is applied to the target reference position, that is, the slave target reference position is controlled to match the slave cylinder's position with the master cylinder's position. In the simulation based on a Simulink model, the proposed algorithm shows a better synchronization performance in aspect of the mean of the absolute error and the peak synchronization error.

• Journal of Information Technology Applications and Management
• /
• v.21 no.3
• /
• pp.1-17
• /
• 2014

In this study, various characteristics of R&D related economic variables were studied to analyze complexity of science and technology activities in Korea, as reliance of R&D activities of the private sector is growing by the day. In comparison to other countries, this means that it is likely to be fluctuated by economic conditions. This complexity characteristic signifies that the result of science and technology activities can be greatly different from the anticipated results - depending on the influences from economic conditions and the results of science and technology activities which may be unpredictable. After reviewing the results of 17 variables related to science and technology characteristics of complex systems intended for time-series data - in the total R&D expenditure, and private R&D expenditure, numbers of SCI papers, the existence of chaotic characteristics were. using Lyapunov Exponent, Hurst Exponent, BDS test. This result reveals science and technology activity of the three most important components in Korea which are; heavy dependence on initial condition, the long term memory of time series, and non-linear structure. As stable R&D investment and result are needed in order to maintain steady development of Korea economy, the R&D structure should be less influenced by business cycles and more effective technology development policy for improving human resource development must be set in motion. And to minimize the risk of new technology, the construction of sophisticated technology forecasting system should take into account, for development of R&D system.

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.135-141
• /
• 2002

This paper presents an implementation of high-dynamic performance of position sensorless motion control system of Reluctance Synchronous Motor(RSM) drives for an industrial servo system with direct torque control(DTC), The problems of DTC for high-dynamic performance and maximum efficiency RSM drive due to a saturated stator linkage flux and nonlinear inductance curve with various load currents, The accurate estimation of the stator flux and torque are obtained using stator flux observer of which a saturated inductance Ld and Lq can be compensated by adapting from measurable the modulus and angle of the stator current space vector. To obtain fast torque response and maximum torque/current with varying load current, the reference command flux is ensured by imposing Ids=Iqs. This control strategy is proposed to fast response and optimal efficiency for RSM drive. In order to prove rightness of the suggested control algorithm, the actual experiment carried out at ${\pm}$20 and ${\pm}$1500 rpm. The developed digitally high-performance control system are shown some good response characteristic of control results and high performance features using 1.0kW RSM of which has 2.57 Ld/Lq salient ratio.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.7
• /
• pp.730-736
• /
• 2012

Latest, many researchers do research on wearable robot. The purpose of the researches is very diverse, it will improve efficiency in the industry, taken to replace the many workers in the military field and taken to assist bodily functions run out by aging. However, there is no clear Differentiated strategy depending on the purpose for design and control of the wearable robot. Although a common purpose is to drive the robot by the sensor signal (intent signals), the optimization about the mechanism and control studies must be done according to the user's physical ability and purpose. In this study, the study's first phase for the development of wearable robotic gait rehabilitation, gait characteristics were analyzed elders and hemiplegia patients using a 3D gait analysis system (VICON512). As a result, asymmetric gait characteristics of the hemiplegia patients were found compared with the normal elderly.

• Safety and Health at Work
• /
• v.13 no.3
• /
• pp.315-325
• /
• 2022

Background: Firefighters are required to carry self-contained breathing apparatus (SCBA), which increases the risk of musculoskeletal disorders. This study assessed the newly recruited firefighters' internal forces and potential musculoskeletal disorders when carrying SCBA. The effects of SCBA strap lengths were also evaluated. Methods: Kinematic parameters of twelve male subjects running in a control condition with no SCBA equipped and three varying-strapped SCBAs were measured using 3D inertial motion capture. Subsequently, motion data and predicted ground reaction force were inputted for subject-specific musculoskeletal modeling to estimate joint and muscle forces. Results: The knee was exposed to the highest internal force when carrying SCBA, followed by the rectus femoris and hip, while the shoulder had the lowest force compared to the no-SCBA condition. Our model also revealed that adjusting SCBA straps length was an efficient strategy to influence the force that occurred at the lumbar spine, hip, and knee regions. Grey relation analysis indicated that the deviation of the center of mass, step length, and knee flexion-extension angle could be used as the predictor of musculoskeletal disorders. Conclusion: The finding suggested that the training of the newly recruits focuses on the coordinated movement of muscle and joints in the lower limb. The strap lengths around 98-105 cm were also recommended. The findings are expected to provide injury interventions to enhance the occupational health and safety of the newly recruited firefighters.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.3
• /
• pp.311-322
• /
• 2015

Objective : The purpose of this study was to investigate the effects of landing height and knee joint muscle fatigue on the movement of the lower extremity during cutting after landing. Method : Subjects included 29 adults (age: $20.83{\pm}1.56years$, height: $172.42{\pm}9.51cm$, weight: $65.07{\pm}10.18kg$). The subjects were asked to stand on their dominant lower limb on jump stands that were 30 and 40 cm in height and jump from each stand to land with the dominant lower limb on a force plate making a side step cutting move at a $45^{\circ}$ angle with the non-dominant lower limb. The fatigue level at 30% of the knee extension peak torque using an isokinetic dynamometer. Results : The results showed that the difference of landing height increased maximum range of motion and angular velocity of hip, knee, and ankle joints in the sagittal plane, and in the angular velocity of motion of the hip joint in the sagittal plane. The maximum range of motion of the knee joint in the sagittal plane and the frontal plane decreased on landing from both heights after the fatigue exercise. The angular velocity of the hip joint in the sagittal plane, and the maximum range of motion of the hip joint in the transverse plane decreased for both landing heights after the fatigue exercise. The angular velocity of the hip joint in the frontal plane decreased for the 30 cm landing height after the fatigue exercise. On the other hand, the angular velocity and maximum range of motion of the ankle joint in the sagittal plane for both landing heights, and the angular velocity and maximum range of motion of the ankle joint in the frontal plane increased on landing from the 40 cm height after the fatigue exercise. Conclusion : Different landing heights of 30 and 40 cm and 30% fatigue of peak torque of knee extensor found a forefoot and stiff landing strategy, when cutting after landing. These results might be due to decline in the shock absorption capability of the knee joint and the movement capability related to cutting while increasing the contribution of the ankle joint, which may cause increased ankle joint injuries.

• Journal of the Korean earth science society
• /
• v.26 no.6
• /
• pp.461-468
• /
• 2005

The purpose of this study is to investigate the abilities of 6th grade students to assess the relationship between spatial capability, concept of celestial motion, and science process skills, which can help find a better teaching strategy for students in understanding the concept of celestial motion. The results are as follows. First, in terms of level of accomplishment of these three skills, male students show higher level of accomplishment than female students, but significant differences are found. Second, according to the analysis of the effect of spatial capability and concept of the movement of heavenly bodies, the former has a stronger influence on the students' cognition of celestial motion. Minor elements of spatial capability that influence the conception of celestial motion are device analogy, calculation of wood cut, and revolving light. Third, spatial capability is very influential on the level of accomplishment in science process skills. Among the minor elements of spatial capability that is influential to science process skills, calculation of wood cut is the highest, especially when various elements are interactively related to each other.