• Fisheries and Aquatic Sciences
• /
• 제2권2호
• /
• pp.149-154
• /
• 1999

Response Surface Methodology was applied for optimizing the processing parameters of ultrasound treatment in order to produce low-molecular alginate. The use of ultrasound significantly reduced viscosity of alginate solutions. Suggested parameters of ultrasound treatment for maximum reduction of alginate molecular weight were: specific intensity, 115.81 $W/cm^2$ at 20kHz frequency; treatment time, 35.55 min; temperature, $20.08^{\circ}C$; alginate concentration, $2.5\%$. Low-molecular alginate obtained by ultrasound had two peaks on Sepharose CL-6B gel filtration. The viscosities of control, fraction I, and fraction II at $0.1\%$ concentration and $25^{\circ}C$ were 3.07, 1.23, and 0.82cps, respectively. Molecular weights of control, fraction I, and fraction II alginates were 336,500, 70,400, and 52,800 daltons, and their solubilities were 3, 6, and $14\%$, respectively. The lower molecular weight of alginate, the lower the alcohol precipitation and the higher $Ca^{2+}$ ion binding capacities. Heavy metal ion binding capacities of alginates were high in the following order of Pb, Cd, Zn, and Co.

• BMB Reports
• /
• 제29권6호
• /
• pp.540-544
• /
• 1996

Ferritins from germinated pumpkin seeds were isolated by ammonium sulfate precipitation (0.55 saturation), ion-exchange chromatography on DEAE-cellulose, and gel filtration chromatographies on Sephacryl S-300 and Sephadex G-100. Pumpkin ferritin contains less iron than soybean ferritin. Pumpkin ferritin cross-reacted with anti-soybean ferritin antiserum made in rabbit, and showed two distinct antibody reactive bands, both of equal intensity. The pumpkin ferritins corresponding to the two bands were separable by centrifugation in a sucrose gradient (20~50%). The molecular weights of the native pumpkin ferritins based on the estimation of sucrose gradient centrifugation, gel filtration on Sephacryl S-300 and non-denaturing polyacrylamide gel electrophoresis appeared to be: 530~580 KD (the large molecular weight pumpkin ferritin) and 330-360 KD (the small molecular weight pumpkin ferritin) The large molecular weight pumpkin ferritin contains less iron. Both pumpkin ferritins cross-reacted with anti-soybean ferritin antibody with a spur formation suggesting partial antigenic recognition.

• Nutritional Sciences
• /
• 제2권2호
• /
• pp.65-70
• /
• 1999

Feeding rats a diet containing bean-hull causes hypertropy in their parotid glands due to the high tannin content. The amount of feedintake of rats led bean-hull was higher than that of rats fed a standard diet. However, the increase in body weight of rats fed bean-hull was lower than that of rats fed a standard diet, which resulted in significantly low feed efficiency of the bean-hull containing diet. Within one week, parotid glands significantly enlarged and a series of proline-rich proteins (PRPs) were produced, which were similar to those induced by feeding high-tannin sorghum with flight differences in molecular weights. Even though the direct comparison between PRPs produced by the bean-hull containing diet and those induced by the high sorghum diet is not appropriate due to laboratory inconsistences, several new PRPs were produced by high tannin diets in both experiments. Differences in molecular weights of PRPs induced in two different tannin sources must be funker investigated to be fully characterized. These morphological and biochemical changes have now been demonstrated to occur in response to the ingestion of tannins, presumably to diminish the anti-nutritional effects of tannins.

• 한국생물공학회:학술대회논문집
• /
• 한국생물공학회 2005년도 생물공학의 동향(XVII)
• /
• pp.287-292
• /
• 2005

The crude polysaccharides(C-CPF, C-CPM, C-CPB) derived from fruiting body, mycelia and mycelia free broth of cordyceps militaris were obtained by ethanol precipitation of hot water extracts. After a batch fermentation of C. militaris was carried out in a 5 L jar vessel, endo-polysaccharide and exo-polysaccharide were obtained. They were demonstrated as the hetero polysaccharides which were composed of glucsose, galactose and mannose by performed with HPAEC(high pH anion exchange chromatography) and conformation of random coil by its complex forming ability with congo red reagent. They were purified by ion exchange (DEAE-cellulose) and gel filtration chromatography. They were monitered by phenol-sulfuric acid method and Bradford method. The NO induction activities of crude polysaccharides and purified polysaccharides derived from mycelia free broth were enhanced rather than LPS(lipo polysaccharide) which was used as a general NO inducer. These effects presumably contibute to the antitumor activities. The homogenieties and molecular weights of polysaccharides were determined by using Sepharose CL-6B. The yield, molecular weights and NO induction activities of C-CPFN Fr.III, C-CPMN Fr.III, C-CPBN Fr.II were 0.387, 0.408 and 0.153, 127 K 210 K and 36 K, 40.79%, 88.72%, and 104.17%, respectively.

• 폴리머
• /
• 제37권2호
• /
• pp.135-140
• /
• 2013

Poly(methyl acrylate)-poly(acrylonitrile) 공중합체의 응력완화 실험은 용매기를 부착한 인장 시험기를 사용하여 여러 온도의 공기 중, 증류수, pH 3, 7, 11 용액에서 실행하였다. Ree-Eyring and Maxwell 모델로부터 얻은 완화스펙트럼 식에 실험적인 응력완화 곡선을 대입하여 poly(methyl acrylate)-poly(acrylonitrile) 공중합체의 완화스펙트럼을 얻었다. 완화스펙트럼의 계산은 Laplace 변환법을 사용한 컴퓨터 프로그램을 이용하였다. 이들 시료의 완화스펙트럼은 유동단위의 분자량과 자체확산 분포와 밀접한 관계가 있음을 알 수 있었다.

• 한국염색가공학회지
• /
• 제33권3호
• /
• pp.147-152
• /
• 2021

Bulk polymerization was used to produce poly(vinyl acetate) with different molecular weights, which were then saponified to prepare poly(vinyl alcohol) (PVA) with different molecular weights. With P_n of 2,060 and 3,240, the optimum film formation concentrations of PVA were found 7.5wt.% and 6.5wt.%, respectively. The drawing characteristics of the PVA film prepared at the optimum film formation concentrations were experimented, as well as the thermal characteristics of the PVA film based on the drawing ratio were observed. When the drawing velocity was fixed, it was found that the drawing ratios of all samples decreased as the heat band gap increased, and the melting temperature of the PVA film slightly increased as the drawing ratio increased regardless of the P_n of PVA.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제48권2호
• /
• pp.86-97
• /
• 2024

Alkaline- or salt-assisted extractions have been widely used to extract edible insect proteins, however, there is a need for extraction techniques that balance cost-efficient production as well as preserving the protein properties. Mealworm proteins (Tenebrio molitor larvae) were extracted using three different extraction methods-alkali (AMP), salt (SMP), and water (WMP)-and then physicochemical and techno-functional properties were examined. AMP had high yield, protein, and amino acid contents, whereas WMP had high moisture, ash, and fat contents. SDS-PAGE showed a wide range of molecular weights in WMP whereas mostly low molecular weights were observed in AMP and SMP. AMP had poor protein solubilities compared to SMP and WMP across all pHs. AMP had enhanced water-holding capacity and emulsion stability, whereas WMP had improved oil-holding capacity and foaming properties. WMP formed a gel with and without the transglutaminase. The physicochemical and techno-functional properties demonstrated that water-soluble mealworm protein was superior to alkali-and salt-soluble mealworm proteins. Considering the cost efficiency and minimal impact on the environment as well, a cold press juicer could be utilized for mass production of mealworm protein compared to the conventional methods of protein extraction using alkali and salt.

• 한국재료학회지
• /
• 제29권12호
• /
• pp.812-817
• /
• 2019

A zinc-air battery is one of most promising advanced batteries due to its high specific energy density, low cost, and environmental friendliness. However, zinc anodes in zinc-air batteries lead to several issues including self-discharge, corrosion reaction, and hydrogen evolution reaction (HER). In this paper, viscosity of electrolyte has been controlled to suppress the corrosion reaction, HER, and self-discharge behavior. Various viscosity average molecular weights of poly(acrylic acid) (PAA) are adopted to prepare the electrolyte. The evaporation of electrolytes is proportional to the increase in molecular weight. In addition, enhanced self-discharge behavior is obtained when the gelling agent with high molecular weight is used. In addition, the zinc-air cell assembled with lower viscosity average molecular weight of PAA (M_v ~ 450,000) delivers 510.85 mAh/g and 489.30 mAh/g of discharge capacity without storage and with 6 hr storage, respectively. Also, highest capacity retention (95.78 %) is obtained among studied materials.

• Macromolecular Research
• /
• 제13권2호
• /
• pp.147-151
• /
• 2005

The main objective of this study was to modulate pH-sensitive polymers (poly($\beta-amino esters$)) by controlling their molecular weight during their synthesis. These pH-sensitive and biodegradable polymers were synthesized by Michael-type step polymerization. 1,4-Butane diol diacrylate was used as the unsaturated carbonyl compound and piperazine as the nucleophilic compound. Various molecular weight polymers were obtained by varying the mol ratio of piperazine/1,4-butane diol diacrylate. The synthesized polymers were characterized by $^{1}H-NMR$ and their molecular weights were measured by gel permeation chromatography(GPC). The dependence of the molecular weight on the mol ratio was evaluated by the titration method. Also, the pH dependent turbidity of the polymers was determined by UV-Vis spectrophotometry. This pH dependent property of the polymers could be very useful for preparing drug carriers that are sensitive to pH.

• Korean Chemical Engineering Research
• /
• 제56권3호
• /
• pp.343-348
• /
• 2018

Each of the two polycarbonates (PC) of different molecular weights was blended with acrylonitrile-butadiene-styrene (ABS) under high-shear rate processing to afford PC/ABS. Sizes of ABS dispersed phases and mechanical properties of PC/ABS blends were investigated and high-shear rate processing of PC/ABS was carried out by changing screw speed and processing time. Prepared specimens were examined by scanning electron microscope (SEM) to observe morphology changes. Sizes of ABS dispersed phases in PC/ABS blends were observed to decrease gradually as screw speeds increased. Tensile strengths and elongations of specimens were investigated by universal testing method (UTM) to study the influence of molecular weight of PC exerting on PC/ABS blends. As a result, PC1/ABS blends (PC1: higher molecular weight PC) exhibited more strengthened properties than PC2/ABS (PC2: lower molecular weight PC). The tensile strength of PC1/ABS showed an increasing tendency when the screw speed increased, and the elongation did not show a significant decrease, but increased slightly with increasing shear time at a constant screw speed of 1000 rpm.