• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 E
• /
• pp.1670-1674
• /
• 1998

Now and then there are many electrical accidents between cable and line post insulator which is degraded by long time using, causing leakage current on the surface of insulator. In this paper it is denied that the 22.9 KV-y distribution lines are protected by binding cover which is needed from fog or rainy moisture, surges occurring by swiching or lightening pulse. It is analyzed to investgate the unballanced transfer characteristics and reflection coefficient by using bidding cover and non-cover. It was tested the radio interference voltage in the test room. In the factory it was tested the amount of leakage current causing on the surface of insulator in the state of no load and 70(%) load.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1871-1873
• /
• 2000

There are many electrical accidents between bare wire and line post insulator which is degraded by long time using, causing leakage current on the surface of insulator. In this paper it is presented that the 22.9 Kv-y distribution lines are protected by binding cover which is needed from fog or rainy moisture, surges occurring by switching or lightening pulse. It is analyzed to investigate the unbalanced transfer characteristics and reflection coefficient by using binding cover and non-cover. It was tested the radio interference voltage in the test room and electric field strength by calculation between binding cover and non-cover. In the factory the leakage current causing on the surface of insulator was tested in the state of light load and heavy load.

• 대한기계학회논문집B
• /
• 제33권8호
• /
• pp.629-634
• /
• 2009

In this paper, drying mechanism is analyzed for improving the energy efficiency of an electric clothes dryer which consumes more electric power than other appliances. For the purpose, characteristic curves of the dryer such as temperature, relative humidity, evaporation rate, mass transfer coefficient, remaining moisture content curves are experimentally obtained. Based on the experimental results and analysis of drying mechanism, the effect of power of a heater and heat loss on the power consumption of an electric clothes dryer are systematically presented. These results demonstrate the feasibility of controlling heat loss at the heater as well as the backduct component to decrease the power consumption of an electric clothes dryer.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2262-2267
• /
• 2008

In this paper, drying mechanism is analyzed for improving the energy efficiency of an electric clothes dryer which consumes more electric power than other appliances. For the purpose, characteristic curves of the dryer such as temperature, relative humidity, evaporation rate, mass transfer coefficient, remaining moisture content curves are experimentally obtained. Based on the experimental results and analysis of drying mechanism, the effect of power of a heater and heat loss on the power consumption of an electric clothes dryer are systematically presented. These results demonstrate the feasibility of controlling heat loss at the heater as well as backduct component to decrease the power consumption of an electric clothes dryer.

• Transactions on Electrical and Electronic Materials
• /
• 제13권6호
• /
• pp.273-277
• /
• 2012

The vacuum drying process for drying of paper in current transformers was modeled with an aim to develop an understanding of the drying mechanism involved and also to predict the water collection rates. A molecular as well as macroscopic approach was adopted for the prediction of drying rate. Ficks law of diffusion was adopted for the prediction of drying rates at macroscopic levels. A steady state and dynamic mass transfer simulation was performed. The bulk diffusion coefficient was calculated using weight loss experiments. The accuracy of the solution was a strong function of the relation developed to determine the equilibrium moisture content. The actually observed diffusion constant was also important to predict the plant water removal rate. Thermo gravimetric studies helped in calculating the diffusion constant. In addition, simulation studies revealed the formation of perpetual moisture traps (loops) inside the CT. These loops can only be broken by changing the temperature or pressure of the system. The change in temperature or pressure changes the kinetic or potential energy of the effusing vapor resulting in breaking of the loop. The cycle was developed based on this mechanism. Additionally, simulation studies also revealed that the actual mechanism of moisture diffusion in CT's is by surface jumps initiated by surface diffusion balanced against the surrounding pressure. Every subsequent step in the cycle was to break such loops. The effect of change in drying time on the electrical properties of the insulation was also assessed. The measurement of capacitance at the rated voltage and one third of the rated voltage demonstrated that the capacitance change is within the acceptance limit. Hence, the new cycle does not affect the electrical performance of the CT.

• Journal of the Korean Wood Science and Technology
• /
• 제44권3호
• /
• pp.370-380
• /
• 2016

제주도 지역에서 소나무재선충병 피해를 받은 곰솔 원목의 이용확대를 위하여 열처리를 수행하였다. 열처리는 처리 원목의 중심부가 소나무재선충의 사멸온도인 $56^{\circ}C$를 30분간 유지하여야 한다. 곰솔 원목의 초기함수율과 말구지름은 각각 46% ~ 141%, 180 mm ~ 500 mm의 범위이고, 기본비중과 전건비중은 각각 0.47, 0.52이었다. $105^{\circ}C$ 조건에서 함수율과 말구지름에 따라 열처리에 소요되는 시간은 7.7 h ~ 44.2 h의 범위로 측정되었다. 다양한 함수율 및 지름을 갖는 곰솔 원목의 열처리 소요시간을 예측하기 위하여 열처리 진행 중 처리목 내부의 온도분포를 유한차분법을 적용한 2차원 열전달 해석을 통하여 제시하였다. 열전달 해석을 위한 목재의 열적 특성은 함수율에 따른 열전도계수와 비열을 적용하였으며, 자연대류와 강제대류를 합한 형태의 혼합대류에 의한 혼합대류계수를 적용하였다. 실험값과 예측 값의 오차는 3 ~ 45%의 범위로 분석되었다. 곰솔 원목에서 초기함수율이 50%이고, 말구지름이 200 mm, 300 mm, 400 mm인 경우, 예측된 열처리 소요시간은 각각 10.9 h, 18.3 h, 27.0 h이었다. 초기함수율이 75%일 때, 지름에 따라 각각 13.6 h, 22.5 h, 32.8 h이고, 초기함수율이 100%일 때, 지름에 따라 각각 16.2 h, 26.5 h, 38.2 h이었다. 이러한 열처리 소요시간의 예측방법에 소나무와 잣나무 등 다른 소나무재선충병 피해목의 물리적 특성을 적용하면, 함수율과 말구지름에 따른 열처리 소요시간을 제시할 수 있을 것으로 판단된다.

• 한국수산과학회지
• /
• 제14권4호
• /
• pp.189-193
• /
• 1981

등온흡습곡선측정시의 건제품이 주어진 대상습도에서 평형에 이르는 시간을 단축시키기 위하여 조절기류를 이용하는 장치를 만들고, 이를 이용하여 $25^{\circ}C$에서 말쥐치 건제품의 등온흡습곡선을 측정하였다. 1. 조절기류를 이용함으로써 주어진 수분활성에서보다 높은 수분활성에 이르는 시간을 평균 45 시간으로 단축시킬 수 있었다. 2. 단분자의 수분함양은 고형물 1kg당 0.092kg이었으며, 건조말쥐치의 제품에 대하여 $8.42\%$였다. Symbols used in the text A : surface, $m^2$ $a_w$: water activity $A_s$ : specific surface, $m^2/kg$ dry matter C : constant related to the heat of adsorption $K_g$ : gas film coefficient of mass transfer, $kg water/hr{\cdot}Pa{\cdot}m^2$ n : number of molecular layers $n_s$ : moisture content, kg water /kg dry matter $n_{sa}$ : mean moisture content, kg water/kg dry matter $n_{se}$ : equilibrium moisture content, kg water/kg dry matter $n_{sm}$ : moisture content for monolayer, kg water/kg dry matter $P_g$ : saturated vapor pressure at wet-bulb temperature, Pa $P_a$ : partial vapor pressure of water in air, Pa $R_d$ : resistance factor against diffusion, $m^2{\cdot}hr/kg$ dry matter $R_s$ : resistance factor against drying, $m^2{\cdot}hr/kg$ dry matter R.H. : relative humidity, $\%$ $\varphi$ : R.H./100

• 한국식품과학회지
• /
• 제18권5호
• /
• pp.351-356
• /
• 1986

단(單)원통형 및 원통형 드럼건조기를 이용하여 잘게 저민 생선으로부터 플레이크를 성공적으로 만들 수 있었다. 생선의 높은 지방함량으로 인해 저민 생선이 드럼에 잘 들러붙지 않는 문제점은 타피오카가루의 형태로 2.5%의 전분을 저민 생선에 첨가함으로서 건조양상에는 영향을 미치지 않으면서 해결될 수 있었다. 제품의 수분함량을 일정한 수준으로 유지할 경우 건고형분(乾固形分)의 생산속도는 드럼간의 간격을 최소로 줄였을때 최고에 도달하였다. 건고형분(乾固形分)의 생산속도는 드럼의 회전속도가 증가할수록 선형적으로 증가하였고 제품의 품질이 손상되지 않는 범위에서 스팀의 압력이 높을수록 증가하였다. 총괄 열전달계수는 드럼의 회전수가 증가함에 따라 증가한 반면에 드럼간의 간격이 커짐에 따라 증가하지는 않았다. $MR\;=\;A\;\exp(\;-k{\theta})$로 표시되는 가장 보편적인 건조 모델식이 드럼건조에도 적용될 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제18권4호
• /
• pp.41-52
• /
• 1990

Experimental external collector type solar lumber dryer with $1.6m^2$ of collector area and $1.0m^3$ of maximum dryer capacity was designed and constructed to investigate the conditions inside and outside the dryer and collector. The efficiency of collector was calculated and numbers of drying-days and collector areas required to dry $0.2m^3$ and $1.0m^3$ of pine and oak at various an flow rate inside collector were estimated for eight cities in Korea. Average temperatures of collector-inlet and -outlet air and heat absorber were $52.5^{\circ}C$ $57.9^{\circ}C$, and $71.1^{\circ}C$. respectively at 4m/sec of an flow rate inside collector on sunny day in summer. Overall heat transfer coefficient of collector was 4.875W/$m^2^{\circ}C $ and collector efficiency was 52%. Estimated numbers of drying-days required to dry $0.2m^3$ of pine and oak from 80% to 15% moisture content at various air flow rate inside collector were 38 and 66 days. respectively. Areas of collector required to dry $1.0m^3$ of lumber at desired safe drying rate were estimated as $13.7m^2$ for pine and $16.0m^2$ for oak.

• 한국식품저장유통학회지
• /
• 제6권3호
• /
• pp.319-323
• /
• 1999

본 연구는 키위를 이용하여 새로운 가공식품을 개발하고자 삼투건조로 전처리하여 열풍, 진공, 동결건조한 후 삼투처리 유무에 따라 각각의 품질특성을 비교 평가하였다. 수분함량은 무처리 및 삼투처리한 키위를 열풍 진공, 동결건조 하였을 때 무처리가 삼투처리한 경우 보다 낮았다. 건조방법에 따른 vitamin C의 함량은 무처리보다 삼투처리가 낮았으며 건조시간에 따른 vitamin C의 함량변화는 동결, 진공건조시 완만한 감소를 보이는 반면 열풍건조한 경우는 많은 감소를 보였다. 수분의 이동을 나타내는 확산속도는 무처리의 경우 열풍건조가 가장 빨랐으나 삼투처리 후에는 진공건조가 가장 빠르게 나타났다. 세 가지 건조방법 모두 삼투처리가 빠른 건조 양상을 보여 효과적인 전처리 방법임을 확인 할 수 있었다. 품질변화 특성은 열풍, 진공 동결건조 모두 2차 반응속도식이 품질변화예측 모델식으로 적합한 것으로 나타났다.