• Journal of Biosystems Engineering
• /
• v.21 no.1
• /
• pp.21-33
• /
• 1996

This study was to obtain basic information needed to develop the effective weed control method for the production of less polluted agricultural products by inducing viability loss of weed seeds in soil with infrared irradiation. Ceramic plates were heated by LPG with the aid of forced air and the infrared produced from plates was used as the heat source for heating soil. The soil heated in this study was sandy loam with four levels of moisture contents (0.5, 5.1, 9.1, 15.0% wb). The temperature distribution was measured at various soil depths when soil was irradiated with infrared for different irradiation time (30, 60, 90 sec). The soil depths with duration time of minimum 3 minutes over $80^circ C$, temperature inducing viability loss of weed seeds, were investigated. When the moisture content of soil was 0.5% and 5.1% wb, the soil depths which can induce viability loss of weed seeds was greatly increased with increasing irradiation time. When 30 seconds of irradiation time was applied on soil with moisture content of 9.1% or 15.0% wb, any depths of soil tested in this study was not reached to the temperature of 8$0^{\circ}C$. Generally, the soil depth being needed for viability loss of weed seeds was decreased with increasing moisture content of soil.

• Journal of Biosystems Engineering
• /
• v.16 no.3
• /
• pp.263-271
• /
• 1991

When grains is subjected to oscillating load, the dynamic viscoelastic behavior of the material will be describe the complex modulus of the material. The complex modulus and therefore the storage modulus, the loss modulus, and the phase angle for the sample should be obtainable with a given static viscoelastic property of the material under static load. The complex relaxation moduli of the rough rice kernel were computed from the Burger's model describing creep behavior of the material which were obtained in the previous study. Also, the effects of cyclic load and moisture content of grain on the dynamic viscoelastic behavior of the samples were analized. The storage modulus of the rough rice kernel slightly increased with the frequency applied but at above the frequency of 0.1 Hz it was nearly constant with the frequency, and the loss modulus of the sample very rapidly decreased with increase in the frequency on those frequency ranges. It was shown that the storage modulus and the loss modulus of the sample increased with decrease in grain moisture content. Effect of grain moisture content on the storage modulus of the sample was highly significant than effect of the frequency applied, but effect of the frequency on the loss modulus of the sample was more significant than effect of grain moisture content.

• Journal of the Korea Concrete Institute
• /
• v.16 no.5 s.83
• /
• pp.725-731
• /
• 2004

A field test program was conducted for the newly placed concrete pavement of US Interstate Highway 10 between March 26th and 28th, 2003. The test section was located between Van Horn and Sierra Blanca in Hudspeth County approximately 130 km east of El Paso, Texas. The main objective of the test was collecting moisture-related data to validate the models of effective curing thickness, evaporation rate, and moisture-based maturity. Effect of moisture loss on drying shrinkage strain was studied using additional test instrumentation.

• Asian-Australasian Journal of Animal Sciences
• /
• v.5 no.4
• /
• pp.629-634
• /
• 1992

Seventeen Japanese Black steers were used to evaluate the influence of slaughter weight (550 kg, 600 kg or 650 kg), sire (two sires), concentrate feeding (barley or corn) and muscle (six muscles) on the following characteristics: pH value, cooking loss, shear value, moisture and crude fat contents. Crude fat contents were higher, and moisture content and shear values were lower in muscles from the large slaughter weight group 650 kg than those from other slaughter weight groups. Cooking loss, shear value, moisture and crude fat contents differed between sires. Corn feeding increased crude fat content in muscle compared to barley feeding. Muscles containing a large amount of intramuscular fat showed lower shear values and less cooking loss than those containing a small amount of intramuscular fat.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.65-83
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well. 2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air. 3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying. 4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis. 5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time. 6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture. 7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation. 8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise. 11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss. 12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method. 13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated. Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year. 14. Required fan horsepower and energy for the intermittent fan operation were 3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation. 15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use. 16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.64-64
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well.2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air.3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying.4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis.5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time.6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture.7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation.8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise.11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss.12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method.13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated.Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year.14. Required fan horsepower and energy for the intermittent fan operation were3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation.15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use.16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.229-232
• /
• 1997

A free space transmission method using standard gain horn antennas in the frequency range from 9.0 to 10.5GHz is applied to determine the dielectric properties of grain such as rough rice, brown rife and barley. The dielectric constant and loss factor, which depend on the moisture content of the wetted grain are obtained from the measured attenuation and phase shift by vector network analyzer. The effect of density fluctuation, which is an important parameter governing the dielectric properties of grain, on the dielectric constant and loss factor is presented. A new density-independent model in terms of measured attenuation and moisture density is proposed for reducing the effects of density fluctuation on the moisture content measurement.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.8-12
• /
• 2022

Water loss is one of the typical but challenging problems in water management. To reduced water loss or increase water efficiency, the pilot projects were implemented in the TTD's irrigation area. Modern soil moisture technology and local level water user training were conducted together as a mean to achieve improved water efficiency. In terms of technology, soil moisture sensors and monitoring system were used to estimate crop water requirement to reduce unnecessary irrigation. This was found to save 16.47% of irrigated water and 25.20% of irrigation supply. Further improvement of water efficiency was gained by means of local level water user training in which stakeholders were engaged in the network of communications and co-planning. The lessons learnt from the TTD pilot project was translated into good water management practices at local level.

• Advances in concrete construction
• /
• v.13 no.6
• /
• pp.423-431
• /
• 2022

Although the influence of moisture content on the mechanical properties of concrete has been studied for a long time, research related to its influence on the damping and energy dissipation property of concrete structure is still very limited. In this paper, the relationship between damping property and moisture content of concrete using cyclic uniaxial compression is firstly presented, and the mechanism of the influence of moisture content on concrete damping and energy dissipation capacity is analyzed. Based on the experimental research, moisture-related damping and energy dissipation model is proposed. Results show that the dissipated energy of concrete and loss factor increase as the moisture content increasing. The energy dissipation coefficient reflecting the influence of stress level of concrete under cyclic load, decreases first and then increases as the moisture content increasing. The mechanism of moisture-related energy dissipation behavior can be divided into the reactive force of water, the development of the internal micro cracks and the pore water pressure. Finally, the proposed moisture-related damping and energy dissipation model are verified.

• Journal of Fashion Business
• /
• v.7 no.2
• /
• pp.69-81
• /
• 2003

Among the various properties of textile fabrics, the moisture-related properties are important for the textile processes or the apparel comfort characteristics. Alkaline hydrolysis results in pitting on the surface of fibers and increases the amount of hydroxyl and carboxyl end groups of the PET molecules on the fiber surface. The purpose of this study is to investigate the moisture-related properties of PET fabrics treated with quaternary ammonium compound/alkaline solution. The wetting and wicking properties of the PET fabrics were measured using the following experiments: contact angle, surface free energy, work of adhesion, vertical wicking height, moisture regain, and frictional static voltage. It was concluded that by the alkaline hydrolysis process, surface hydrophilicity and reactivity were considerably improved especially at lower levels of weight loss% and that the pitting of the fiber surface resulted in at higher levels of weight loss% was disadvantageous in moisture-related properties of PET.