• 펄프종이기술
• /
• 제29권3호
• /
• pp.17-25
• /
• 1997

Natural water-soluble polymers such as starch, casein and carboxy methyl cellulose(CMC) have been limited in their uses. However, the proper water retention of coating colors can not be obtained without addition of these polymers. Furthermore, the coating runnability and the physical properties of coated paper were not also satisfied. Therefore, the objective of this study was to synthesize the water retention and flow modifiers which can improve the water retention and flow properties of coating colors. We have measured physical properties of flow modifiers and coating colors which included flow modifiers. The viscosity of flow modifiers was very low at acid pH, and rapidly increased at about pH 7, and gradually reached to equilibrium at alkali pH. Such an increase comes from the molecular weight of flow modifiers and the amount of acrylic and methacrylic acids. The viscosity of coating color containing the flow modifiers was lower than that containing CMC. However, both of them had little difference in water retention. The water-phase viscosity of synthetic modifier containing coating color was either higher or similar compared to that of CMC containing coating color. The high shear viscosity of coating colors was low. Therefore, it can be concluded that the synthetic flow modifiers are very useful for improvement of flow properties and water retentions.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.917-917
• /
• 2003

The auditory experiments based on the subjective annoyance responses were undertaken for the establishment of the adverb modifiers of the heavy-weight impact noises. The standard heavy weight impact noise, impact ball noise and adult walking noise were recorded by dummy head at a newly-built apartment and were presented to the subjects by headphones. The levels of the three impact noises were varied from 30 to 60㏈(A) and the subjects matched one of the adverb modifiers to each level of the noise sources. As a result, seven scale modifiers were established and the intervals between the modifiers were found as equal. In addition, it was found that the lower annoyance noise limits for the heavyweight impact, impact ball and walking were 40-45㏈ (L$\sub$I, Fmax. AW), which is 6㏈ lower than in the previous study. The background noise level was as low as 21㏈(A) in the test booth, therefore, the testing conditions need to be concerned for evaluation of floor impact noise.

• 폴리머
• /
• 제31권1호
• /
• pp.68-73
• /
• 2007

도로 포장용 아스팔트의 성능을 개선하기 위하여 유화중합법으로 반응성 고분자 개질제들을 합성하였다. Styrene, methyl methacrylate (MMA) 및 isoprene과 아스팔트의 아스팔텐 성분의 carboxyl group과 반응시키기 위하여 epoxy ring을 가진 glycidyl methacrylate(GMA)를 단량체로 사용하였다. 단량체의 조성을 다양하게 변화시켜 개질제들을 중합하고, 중합된 개질제와 아스팔트의 상용성을 검토하였다. 혼합이 잘 되는 개질제들에 대하여 시차주사열량계 (DSC)로 $T_g$를 측정하였다. 합성 후 epoxy ring의 존재 여부와 아스팔텐과의 반응성을 알아보기 위해 푸리에 변환 적외선 분광기(FTIR)를 이용하였고, 핵자기공명법(NMR)으로 개질제 분자 구조의 해석을 행하였다. 아스팔트와 혼합이 잘 이루어지는 개질제들은 $T_g$가 $37.5{\sim}56.5^{\circ}C$ 사이이며, isoprene의 비율이 30 wt%이었다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.21-24
• /
• 2003

In general, to enhance physical properties of PET-layered silicate nanocomposites $(P_{et}LSNs)$, it has been well known that the organic modifiers should introduce into gallery regions. However, the organic modifiers in$(P_{et}LSNs)$ may result in thermal decomposition by melt processing at high temperature, and it necessarily lead to deteriorate various physical properties of final products. Therefore, in this study, $(P_{et}LSNs)$ excluding and including organic modifiers were prepared by solution method $(S-P_{et}LSNs_{eom} and S-P_{et}LSNs_{iom})$ and we (focused on the effects of the organic modifiers in $P_{et}$ LSNs with exfoliation structure on the crystallization behaviors, the optical transparency, the thermal stability and the mechanical property. The absence and existence of organic modifiers in $S-P_{et}LSNs_{eom} and S-P_{et}LSNs_{iom}$ were investigated by EA and TGA, and nano-structure of silicate layers in $S-P_{et}LSNs$ was evaluated by using WXRD, SAXS and TEM. $S-P_{et}LSNs_{eom} and S-P_{et}LSNs_{iom}$ were mixed with neat PET as masterbatches by melt method $(M-P_{et}LSNs_{eom} and M-P_{et}LSNs_{iom})$, and also neat PET was mixed with organically modified layered silicates (OLS) by conventional direct melt method $(D-P_{et}LSNs) at 270^{\circ}C$. As results, it was found that $M-P_{et}LSNs_{eom}, M-P_{et}LSNs_{iom}, and D-P_{et}LSN$ showed a exfoliated structure and exhibited faster crystallization rate, better thermal stability and mechanical property than those of neat PET due to the dispersed and detaminated silicate layers in PET matrix. Whereas, considering organic modifiers effect, $M-P_{et}LSNs_{eom} and D-P_{et}LSN$ exhibited slower crystallization rate, poorer optical, thermal and mechanical properties, in comparison to $M-P_{et}LSNs_{eom}> due to the thermal decomposition of organic modifier in $D-P_{et}LSNs$ during melt method.

• 한국주조공학회지
• /
• 제11권4호
• /
• pp.314-322
• /
• 1991

In this study, Na, Li, Sb, Sr were added as the modifiers to improve the mechanical proper ties of Al-Si alloys and their effects were compared one another Thermal analysis was carried out to measure the degree of undercooling, that is, the basic mechanism of modifying effect. The measurements of holding time and analyses of components of Al-Si alloys were carried out to compare the fading of the modifiers. Greater degree of undercooling was measured from the modified alloy than the normal alloys. In the modified alloy, the shape of Si was changed into a fine fiber phase or a lamellar phase from the coarse plate phase. There are not modifying effect of Sb below the $1.5^{\circ}C$ /sec of cooling rate. As the cooling rate increases, similar effects appears in the non-modified alloys like the modified alloys. Na and Li were faded in short time and were difficult to control on the melt, but Sb and Sr were scarcely faded for 6 hours of holding and were easy to control on the melt. Na and Sr are the good modifiers in terms of microstructure. Sb is the best modifier, but Na, Li are the inadequate modifiers in terms of fading.

• Archives of Pharmacal Research
• /
• 제23권2호
• /
• pp.163-166
• /
• 2000

The effects of modifiers such as methanol, water diethylamine in methanol (10 v/v %), and diethylamine in water (10 v/v %) were investigated at three different concentrations (1, 5, and 10 v/v %) of the modifiers in supercritical $CO_2$ (SC-$CO_2$) in order to enhance the supercritical fluid extraction (SFE) efficiency of cephalotaxine from Cephalotaxus wilsoniana Leaves. Among the modifiers employed, methanol basified with diethylamine was found to greatly enhance the extraction efficiency relative to any other modifiers employed. The results suggest that cephalotaxine in plant matrices may be readily changed from SC-$CO_2$-insoluble salt to SC-$CO_2$-soluble free base by basified modifiers. In addition, SC-$CO_2$modified with basified methanol could enhance the extraction efficiency of cephalotaxine more than 30% when compared to the conventional organic solvent extraction.

• 폴리머
• /
• 제27권6호
• /
• pp.589-595
• /
• 2003

서로 다른 종류의 유기 개질제가 층간에 삽입된 세 종류의 몬모릴로나이트 (MMT)를 사용하여 불포화 폴리에스터 (UP)/MMT 나노복합체를 제조하고 유기 개질제의 화학적 구조와 각 성분들의 최종 혼합시간이 최종 나노복합체의 형태구조와 각종 물리적 특성에 미치는 영향을 조사하였다. 최종 혼합 시간은 MMT의 종류에 관계없이 나노복합체의 형태구조와 각종 물성에 별다른 영향을 미치지 못하는 것으로 확인되었으며, MMT의 유기 개질제에 두 개의 수산화기가 포함된 Cloisite 30B의 경우에는 나머지 두 종류의 MMT에 비해 형태구조나 고무 평탄 영역에서의 전단 모듈러스 및 굴곡강도 등은 우수한 것으로 나타났다 하지만 인장 강도나 열분해 거동, 유리 전이 온도 등은 별다른 차이를 보이지 않았으며, 또한 MMT의 함량에 따른 각종 특성의 선형적인 증가도 관찰되지 않았다.

• Tribology and Lubricants
• /
• 제8권2호
• /
• pp.7-13
• /
• 1992

Wear experiments were conducted using the SRV machine on the lubricated conditions of the several temperature and load. Oil samples were prepared by adding several friction modifiers into both paraffinic base oil and engine oil. Friction and wear characteristics of the oils were determined and are discussed in connection with the friction modifiers contained, the testing temperature and the load applied. From the study, it was found the MoDTC and the MoDTP, added into the engine oil, caused drastic increase in wear and had a tendendy to lose the friction-reducing property on some specific conditions of temperature and/or load, though they had the good property on other conditions. Ashless friction modifiers and dispersed $MoS_2$ investigated showed the good friction-reducing property, but the loads, where they became active, were different.

• Earthquakes and Structures
• /
• 제22권1호
• /
• pp.83-94
• /
• 2022

In recent years, some studies have identified and quantified factors that can increase or decrease the seismic vulnerability of buildings. These modifier factors, related to the building characteristics and condition, are taken into account in the vulnerability assessment, by means of a numerical estimation resulting from the quantification of these modifiers through vulnerability indexes. However, views have differed on the definition and the quantification of modifiers. In this study, modifier parameters and scores of the Risk-UE Level 1 method are adjusted based on the Algerian seismic code recommendations and the reviews proposed in the literature. The adjusted modifiers and scores are applied to reinforced concrete (RC) buildings in Boumerdes city, in order to assess probable seismic damage. Comparison between estimated damage and observed damage caused by the 2003 Boumerdes earthquake is done, with the objective to (i) validate the model involving influence of the modifier parameters on the seismic vulnerability, and (ii) to define the relationship between modifiers and damage. This research may help planners in improving seismic regulations and reducing vulnerability of existing buildings.

• Elastomers and Composites
• /
• 제57권4호
• /
• pp.215-221
• /
• 2022

In this study, high-penetration asphalt with low greenhouse gas emissions was used in the asphalt mixing process to reduce the carbon emissions during the reaction due to its capacity to be produced even at low temperatures. In effect, cationic, anionic, and non-ionic dispersants were added and mixed in different feeding ratios, seeking an effective dispersion of the modifiers (SIS, PS, TPEE, and SEBS) into the high-penetration asphalt matrix and forming an asphalt binder with a melting point of 120 ℃. The compatibility of the modifiers and the high-penetration asphalt was examined using SEM and DSC techniques, and the role of NDP-1 as a dispersant was carefully investigated with respect to dissolution time. The analyses showed that: (1) the dispersibility of the asphalt binder is good when the non-ionic dispersant is used; (2) as the concentration of the non-ionic dispersant increases, the dissolution time decreases and the domain size contracts; (3) the ND70-PS has the shortest dissolution time, the lowest agglomeration rate, and a single Tg value.