• Corrosion Science and Technology
• /
• v.18 no.6
• /
• pp.232-242
• /
• 2019

In this study, hydrophobically modified fumed silica was added to the PVDF coating to improve corrosion protection performance. Two types of silane modifiers, trimethylchlorosilane (TMCS) and hexamethyldisilazane (HMDZ), were used for hydrophobic modification of the fumed silica. The composition of modified fumed silica was analyzed by Fourier transform infrared, X-ray photoelectron spectroscopy, and elemental analysis. The dispersion of modified fumed silica in the PVDF coating was observed by the transmission electron microscopy, and the hydrophobicity of PVDF coating was analyzed by the water contact angle. Surface properties were examined by the field emission scanning electron microscopy and scanning probe microscopy. Potentiodynamic polarization was conducted to confirm corrosion protection performance of PVDF coating in terms of hydrophobically-modified fumed silica contents. As a result, the average surface roughness and the water contact angle of the PVDF coating increased with modifier contents. The results of the potentiodynamic polarization test showed an increase of the E_corr values with increase of the hydrophobicity of PVDF coating. Thus, it clearly indicates that the corrosion protection performance of PVDF coating improved with the addition of the hydrophobic-modified fumed silica that prevents the penetration of moisture into the PVDF coating.

• Korea-Australia Rheology Journal
• /
• v.16 no.4
• /
• pp.175-182
• /
• 2004

Colloidal coating solution was prepared to enhance the hydrophilic property of the film surface. Water and ethanol were used as the dispersion media and (glycidoxypropyl) trimethoxysilane (GPS) as a binder in the colloidal silica coatings. Ethylene diamine was added to the colloidal silica solution as the curing agent. The colloidal silica solution was regarded as a hard-sphere suspension model with low volume fraction of the silica particles. Rheological properties of the silica suspensions modified with GPS have been investigated as a function of pH and concentration. The acidic solution showed high viscosity change by fast hydrolysis reaction and adsorption of the organic binders on the surface of silica particles. However, the hydrolysis was slow at the basic condition and the binders combined with themselves by condensation. The viscosity change was smallest at pH 7. The viscosity increased with the curing time after adding ethylenediamine, and the increase of viscosity at low pH was higher than that at high pH. The hydrophilic properties of the coating film were investigated by the contact angle of water and film surface. The smallest contact angle was shown under the strong acidic condition of pH 2.

• Journal of the Korean Ceramic Society
• /
• v.45 no.2
• /
• pp.87-89
• /
• 2008

A nano structured silica aerogel thin film was manufactured from inexpensive sodium silicate (water glass) using an ambient pressure drying method. High purity silicic sol was prepared by passing a water glass solution through an ion exchange resin, and the gel films were prepared on a modified glass substrate via dip coating. The dip coating conditions, such as coating time and solvent, were optimized. The optical and physical properties of the obtained silica aerogel thin film were characterized using a UV-visable spectrometer and a scanning electron microscope.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.3
• /
• pp.282-289
• /
• 2010

In preparation of silica aerogel-based hybrid coating materials, the combination of hydrophobic aerogel with organic polar binder material is shown to be very limited due to dissimilar surface property between two materials. Accordingly, the surface modification of the aerogel would be required to obtain compatibilized hybrid coating sols with homogeneous dispersion. In this study, the surface of silica aerogel particles was modified by using both surfactant adsorption and heat treatment methods. Four types of surfactants with different molecular weights and HLB values were used to examine the effect of chain length and hydrophilicity. The surface property of the modified aerogel was evaluated in terms of visible observation for aerogel dispersion in water, water contact angle measurement, and FT-IR analysis. In surface modification using surfactants, the effects of surfactant type and content, and mixing time as process parameter on the degree of hydrophilicity for the modified aerogel. In addition, the temperature condition in modification process via heat treatment was revealed to be significant factor to prepare aerogel with highly hydrophilic property.

• Particle and aerosol research
• /
• v.9 no.4
• /
• pp.209-219
• /
• 2013

We have used the modified diffusion flame burner to synthesize silica coated iron oxide nanoparticles having enhanced superparamagnetic property. Silica-encapsulated iron oxide particles were directly observed using a high resolution transmission electron microscope. From the energy dispersive X-ray spectroscopy (EDS) and zeta potential measurements, the iron oxide particles were found to be completely covered by a silica coating layer. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) measurements revealed that the iron oxide core consists of ${\gamma}-Fe_2O_3$ rather than ${\alpha}-Fe_2O_3$. Our magnetization measurements support this conclusion. Biocompatibility test of the silica-coated iron oxide nanoparticles is also conducted using the protein adsorption onto the coated particle.

• Nano
• /
• v.13 no.12
• /
• pp.1850137.1-1850137.9
• /
• 2018

A series of silica surface-capped with hexamethyldisilazane (denoted as $H-SiO_2$) were prepared by liquid-phase in-situ surface-modification method. The as-obtained $H-SiO_2$ was incorporated into acrylic amino (AA) baking paint to obtain AA/$H-SiO_2$ composite extinction paints and/or coatings. $N_2$ adsorption-desorption tests were conducted to determine the specific surface area as well as pore size and pore volume of $H-SiO_2$. Moreover, the effects of $H-SiO_2$ matting agents on the physical properties of AA paint as well as the gloss and transmittance of AA-based composite extinction coatings were investigated. Results show that $H-SiO_2$ matting agents possess a large specific surface area and pore volume than previously reported silica obtained by liquid-phase method. Besides, they have better dispersibility in AA baking paint than the unmodified silica. Particularly, $H-SiO_2$ with a silica particle size of $6.7{\mu}m$ and the dosage of 4% (mass fraction) provides an extinction rate of 95.2% and a transmittance of 79.3% for the AA-based composite extinction coating, showing advantages over OK520, a conventional silica matting agent. Along with the increase in the silica particle size, $H-SiO_2$ matting agents cause a certain degree of increase in the viscosity of AA paint as well as a noticeable decrease in the gloss of the AA-based composite extinction coating, but they have insignificant effects on the hardness and adhesion to substrate of the AA-based composite coatings. This means that $H-SiO_2$ matting agents could be well applicable to preparing low-viscosity and low-gloss AA-based matte coatings.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.2
• /
• pp.185-195
• /
• 2011

Carbon nanotube(CNT) plays an essential role in various fields of nano based science and technology. Recently, silica coated CNT composites are interested because they are useful for the optical, magnetical, and catalytic applications. In this report, carboxyl groups were introduced on the MWCNT using nitric acid. In order to maximize the silica encapsulation efficiency, carboxyl groups of MWCNT reacted with a silane coupling agent were used to prepare silica coated MWCNT. Due to their strong interaction between modified MWCNT and TEOS. Silica layer with a controllable thickness was achieved. Silica coated MWCNT were further utilized as the template for the synthesis of hollow silica nanotubes after $800^{\circ}C$ calcination.

• Journal of the Korean Solar Energy Society
• /
• v.36 no.5
• /
• pp.1-8
• /
• 2016

In this paper, we evaluated the effect of a silica-based Anti-Reflection(AR) coating for PV modules. The coating technique can be easily applied to large-scale PV modules at room temperature with improvements of the optical properties that is qualified by the optical transmission measurements on the coated cover glass of the modules. The power improvement of the large-scale PV modules shows the increasing about 2.4% at standard condition of the coating technique on average. To improve the AR coating effect of the PV modules, we have characterized the individual PV modules by the measurements of DC power output, modified performance ratio(PRm) and the regression. The results show that the significant improvements of the AR coating effect are 6.4%, 5.5% and 4.5% of increasing of the performances by using the measurements of DC power output, modified performance ratio(PRm) and the regression, respectively.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.07a
• /
• pp.129-132
• /
• 2003

Silica/SUS composite membranes were prepared for CO removal from products of methanol steam reforming. A support was prepared by coating Ni powder of sub-micron and SiO$_2$ sols of particle size of 500nm and 150nm in turns on a porous stainless steel (SUS) substrate. Silica top layer was coated on the modified support using colloidal sol with nanoparticle. As a result of mixture gas permeation test of silica composite membrane using H$_2$(99%)/CO(1%), CO concentration of 10000 ppm was reduced to under 81 ppm, which is acceptable in PEMFC anode gas specification. Permeation mechanism through the membrane was mainly molecular sieving.

• Elastomers and Composites
• /
• v.53 no.3
• /
• pp.175-180
• /
• 2018

Solution-styrene-butadiene rubber (SSBR) composites were manufactured using four kinds of fillers: silica-silane coated carbon black (SC-CB) hybrid, starch-SC-CB hybrid, pure silica, and pure starch. The influence of filler type on the mechanical properties of the rubber matrix was studied in this work. SC-CB was prepared by silane-graft-coating using vinyl triethoxy silane and carbon black, which enhanced the dispersion effect between the rubber matrix and the filler, and improved the mechanical properties of the compounds. The morphology of the composites was observed by field-emission scanning electron microscopy (FE-SEM). The thermal decomposition behavior of the composites was determined by thermogravimetric analysis (TGA), and the crosslinking behavior of the composites was tested using a rubber process analyzer (RPA). The hardness, tensile strength, swelling ratio, and gas transmittance rate of the composites were evaluated according to ASTM. The test results revealed that with the addition of SC-CB, the hybrid fillers, especially those blended with silica, showed a better reinforcement effect, the highest hardness and tensile strength, and stable thermal decomposition behavior. This implies that the silica-SC-CB hybrid filler has a notable mechanical reinforcement effect on the SSBR matrix. Because of self-crosslinking during its synthesis, the starch-SC-CB hybrid filler produced the most dense matrix, which improved the anti-gas transmittance property. The composites with the hybrid fillers had better anti-swelling properties as compared to the neat SSBR composite, which was due to the hydrophilicity of silica and starch.