• Journal of Advanced Navigation Technology
• /
• v.27 no.6
• /
• pp.815-820
• /
• 2023

In this paper, the design method of a miniaturized chipless RFID tag using a modified bent H-shaped slot was proposed. The proposed modified bent H-shaped slot was appended on the rectangular conductor plate printed on one side of a 20 mm × 50 mm FR4 substrate with a thickness of 0.8 mm. The resonant dip frequency of the bistatic RCS for the proposed modified bent H-shaped slot was compared with the cases when the H-shaped, U-shaped slot, and bent H-shaped slots were added, respectively, on the conductor plate. The simulated resonant dip frequencies for H-shaped, U-shaped, and bent H-shaped slots were 5.907 GHz, 4.918 GHz, and 4.364 GHz, respectively. When the proposed modified bent H-shaped slot was added, the resonant dip frequency was decreased to 3.741 GHz, and, therefore, the slot length was reduced by 36.7% compared to the H-shaped slot case. Experiment results show that the resonant dip frequency of the fabricated modified bent H-shaped slot was 3.9 GHz.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.11
• /
• pp.70-77
• /
• 1996

In this paper, a modifed TE$_{113}$/TM$_{012}$ triple-mode bandpass filter is implemented by using a modified inter-cavity iris in which the number of slots are reduced upto 50%. In a coventioanl iris two prirs of slot apertures are used to independently couple three resonant modes between two adjacent cavities. However, if transverse magnetic polarizability of a pair of veritcal slot apertures is used to control weak horizontal TE$_{h}$-TE$_{h}$ mode coupling, the width of novel iris slots would substitute for the slot length of the conventional iris, causing to eliminate the horizontal slot apertures. The measured data of two filters, which are the modified filter and ocnventional one, are compared. Experimental result shows that the characteristics of the novel triple-mode filter matches well that of the conventional filter.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.7
• /
• pp.1363-1368
• /
• 2015

Aperture-coupled circular polarization microstrip array antenna is proposed in this paper. The proposed antenna is useful for 2.4GHz ISM band and its aperture shape is a modified H-slot. The optimal design parameters for the antenna structure is found by using electromagnetic analysis tool HFSS repeatedly. The HFSS simulation results, such as return loss, axial ratio, radiation pattern and gain of the proposed array antenna are compared with results of the single antenna. It is able to verify that the proposed array antenna is valuable enough to be used in various applications as well as 2.4GHz ISM band.

• Journal of Biosystems Engineering
• /
• v.31 no.3 s.116
• /
• pp.175-181
• /
• 2006

Nursery pig building is imperative to provide environmental conditions favorable to maintenance of piglet health and the efficiency of growth rate. To meet the ultimate goal, it is necessary to apply proper ventilation design and construction to a confinement livestock building. This study was conducted to investigate the performance of a modified ventilation system in terms of devised slot-inlet (modification I) and exhaust fan (modification II) to improve air change rate in a confined nursery pig building, with dimension of 5.9 m(W) ${\times}$ 12.6 m(L) ${\times}$ 2.2 m(H) in an Darby Genetic Station. The experiment was carried out in August, especially when the outdoor peak temperature were above $30^{\circ}C$ and the measured indoor environmental factors were temperature, air velocity, humidity and ammonia concentration which have been known to affect the piglet health and growth. There was no difference in indoor temperature between the original and modified ventilation systems, however the air velocity and ammonia concentration in confined nursery pig building with modified ventilation system were, in most cases, better performance than original ventilation system. Therefore, it was concluded that the slot-inlet system that kept indoor environmental factors pertinent and had an economic advantage, should be considered as a ventilation system for decreasing sensible heat from piglet in confined nursery pig building during extreme summer season.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.9
• /
• pp.1642-1648
• /
• 2017

Ultra-wideband antennas are desired for several applications including satellite communications, radars, remote sensing system, telescopes, and microwave imaging systems. There are many types of wideband antenna structures, but the tapered slot Vivaldi antenna is advantageous in terms of cost, weight, scan angle capabilities, end-fire radiation, and ease of feeding and system integration. In this paper, a modified antipodal Vivaldi antenna is presented. A novel AVA with H-shaped parasitic patches has the capacity to improve the radiation characteristics in the whole operation frequencies. A prototype of the modified antenna with RT/duroid 5880 substrate of a relative dielectric constant (${\epsilon}_r$) of 2.2, and a thickness of 31mil is fabricated and experimentally studied as well. It measures a ${\mid}S_{11}{\mid}$ of less than -10dB and gain of 9-12dBi over 7.8-52.5GHz which shows reasonable agreement with the simulated one.

• Journal of Biosystems Engineering
• /
• v.7 no.2
• /
• pp.72-85
• /
• 1983

Rice whitening is performed by basically two different whitening actions known as abrasive and frictional. The former adopted in the emery stone abrasive type whiteners and the latter in the jet-air friction type. Comparative milling yields and whitening efficiencies between the whitening system consisting of jet-air friction type whiteners only and the system consisting of both abrasive- and jet-air friction-types have not yet been rigorously defined. This study was to examine the effect of combined operations of abrasive- and jet-air friction-type rice whiteners on milling yields and whitening efficiencies. The small capacity commercial units of the abrasive- and friction-type whiteners were used for the experiments. The combinations of whitening treatments were: 1) Once in the abrasive type and then two to three times in the friction type, 2) twice in the abrasive and then two to three times in the friction type and 3) three to five times in friction type. In these tests, counter pressures for the friction type whiteners were established differently as required to get about the same degree of whitening at the end of predetermined numbers of the repeated operations. The speed of emery stone and the slot angle of the screen were also the factors varied in the abrasive type whitener. Sheukwang rice variety having 13.05% M.C. was used in the tests. The dependent variables were the milled- and head-rice recoveries and electricity consumption. The results of the study are summarized as follows: 1. It was found that in the whitening systems consisting of abrasive- and friction-type whiteners slot angle of the screen, the rotational speed of emery stone roller had significant effect on the milling yields and whitening efficiency. In general, the increase of the emery stone roller speed from 690 to 950 rpm presented a positive effect on milling yield, and one-pass abrasive milling combinations had higher milling yields than two-pass abrasive milling combinations. 2. It was apparent that if the slot angle of the screen and the speed of emery stone roller are modified and set at an optimum level, the combination whitening system consisting of abrasive- and friction-type whiteners is better than the pure frictional whitening system consisting of jet-air friction type in terms of milling yields and efficiencies. 3. In the rice whitening system consisting of abrasive- and jet-air friction-type whiteners, the best whitening performance was obtained when the slot angle of the screen and the rotational speed of emery stone roller were $45^{\circ}$ and 950rpm, respectively, for the one-pass abrasive milling combinations. However, for the two-pass abrasive mi11ing combinations, the best performance was obtained with $75^{\circ}$ of slot angle and 950 rpm of the emery stone roller speed. 4. As compared with pure frictional whitening systems, the combination systems produced more milled rice by 0.8-1.0% point and more head rice by 0.5-1.5% point, and consumed less electricity by 0.15-0.20 KwH per 100kg of milled rice when the abrasive whiteners were operated in the modified conditions as described in item 3 above. Further study is recommended to find out optimum operational and design conditions of abrasive type whiterners.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.220-223
• /
• 2009

Metallic bipolar plate for molten carbonate fuel cell(MCFC) is composed of the shielded slot plate and the center plate. Among these, the center plate plays an important role in gas sealing. Therefore, manufacturing of the center plate is considered one of the key issues in MCFC. The center plate is manufactured by bending process. In bending process, springback and recoiling are two main problems. By using the modified punch shape with 'step', springback and recoil are reduced. The aim of this article is to find the effect of modified punch shape. So, the bending stress along thickness direction and material direction were investigated using FEM.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.2
• /
• pp.70-76
• /
• 2000

A numerical study on the viscous flow around a 2-dimensional circulation control foil is carried out for application on the field of naval architecture and ocean engineering. The governing equations are the RANS and the continuity equations. The equations are discretized by finite difference method and MAC method and the pressure poisson equation is calculate by a SOR method and an O-type non-staggered boundary fitted coordinate system which is overlapped near the slot is used to improve the numerical accuracy. Turbulence is approximated by a modified Baldwin-Lomax turbulence model. In the present paper, the Coanda effect on a 2-dimensional foil of a 20% thickness ellipse with modified rounded trailing edge has been numerically studied. The change in drag and lift of the foil with various jet momentums are calculated and compared to the experimental results to show good agreements.